1980-1982 Yamaha RD350LC 4LO Rebuild. Part 2. How to replace fork seals and fork oil.
ฝัง
- เผยแพร่เมื่อ 28 ส.ค. 2024
- www.itchingtoride.co.uk
You can follow Itching to ride on Facebook, Instagram and TikTok.
How to replace fork seals and fork oil on Yamaha 1980-1982 RD350LC 4LO and RD250LC 4L1.
You can now get 10% off parts and clothing at Orwell Motorcycles. You can use this discount code in store or on there website.
Discount code ITR10.
www.orwell.co.uk
01473 257401
Ipswich
Suffolk
IP2 0AQ
Motorcycle. Motorbike. Rebuild. Strip down. 15W oil. GoPro Hero 9. How to Change fork seals fork oil on Yamaha RD350lc RD250lc.
thank you
CLASS, THANK YOU, HELPED ME OUT OF A MUDDLE :)
Thanks for the video !! I found it easier to take the top clips out with the forks still on the bike. One of the caps wouldn't come out, but I soaked it in WD40 and it popped out overnight.
That was lucky. Can be a nightmare getting them out sometimes. Thanks for watching 😬👍
@@itchingtoride To put the seals in the right way up, is the top of the seal the face with the wider rim? I did one this way (put in the same way as it came out), but then the other fork had the seal the other way round, and this fork had lost nearly all its fork oil. Thanks.
@@ljckclark8973 Hello. I cannot remember what way round they were now. I just put them in the way they come out. Sorry I cannot help. If you have a Haynes manual it should show you in there.
@@itchingtoride NP and thanks
Well done!
Thanks 👍
🏍👍👍👍
Nice tutorial mate👌 think I will just bring them to you 😆
It would be a lot easier mate 😆
Thanks mate I've been looking for information how to do my Yamaha fzr 250 2kr your fork same as mine
Stan Stephens tuned 350 lc was mentor
The yammy 350 rd lc greatest bike if it's ofvtune esdy from 125lc 250 lc 350 lc then 350 YPVS YAMAHA RD350LC two stroke greatest ever !!
I’m restoring an RD250B and have sprayed the engine blocks and heads, what’s the best way to restore the polished edges on the cooling fins? Many Thanks
Hello. I have never worked on a air cooled 250. So never done it mate. Probably wet and dry then Autosol.
If I put the oil level at 75 mil instead of 195mil it means that I will pour no more 140cc of oil but more, right? In the manual it says to use 10w / 30 engine oil and not hydraulic oil for forks; what kind of oil did you use and what alcohol content? I read that someone improves the fork by putting shims under the closing cap of about 3cm, have you ever tried it?
Hello. Use 15W fork oil and do the oil level to 75mm. Yes you will use more oil than 140cc but that’s ok. It say use 10w/30 engine oil because that’s what they used years ago. Now there are better oils to use. I haven’t put shims in before so so that’s up to you if you try that 😬👍
@@itchingtoride Ok thanks, so the advice would be to put more oil, about how much?
Just keep putting it in untill the level is at 75mm 👍
Have you got any tips on how to remove the top cap that pushes down the spring ? My one has rusted and won’t push back up after pushing it down to remove the clip !! Cheers
Hello. Yes I have had it happen a couple of times. I welded a bolt to the cap and used a slid hammer to pull it out. Good luck 😬👍
@@itchingtoride ok ! Thank you , I will give that a go !
If you don’t have a welder you could drill a hole in the cap a put a thread in it. Then Use a slide hammer. You can buy new caps 😬👍
@@itchingtoride Thank you ! That sounds a better option for me as I haven’t tried my hand at welding as yet!
What oil u put in and how much thanks
Hello. I used 15W fork oil. Don’t know how much I used. I just filled it up until the level was at 75mm.
Hi thank for getting back your video help me out
That’s good 😬👍