Hi Ingus, Thanks for your videos. They've given me a lot of insight into how to better setup my VFDs and get the most out of them. Great job! All best.
Thank you for the video. I’m completely new to VFDs, and I got one of these second hand. The instructions are good, but going back and forth is sometimes confusing. This is a great how to set up guide, wish I’d googled earlier!
Awesome video. Have a question. I have one of these on a two stage air conditioning unit. 1st stage blower runs at 30hz 2nd stage blower runs at 60hz When there is no call for blower my vfd will run 20hz constantly. Can you help me understand that please?
Hi! Great video. I am stuck with getting the motor spin higher than 3 hz. I can tune it on PU btween 0.5 and 3 ish hz but setting to let say 50 it still run around 3 hz. Can't find it online.
Magandang gabe Po maraming salamat po sa magandang Nakita ko Po na tutorial sa iyo laking tolung Po eto sa akin Po masi may kinabet Po Ako na tolad din Po sa inyo na prequincy inverter sa cobior Ng keyampo sana magawa ko na Po siting lang Po Ng inverter Ang kulang thank you Po ulit god bless
Hi, thanks for the video. Do you have a video where you explain how to download the parameter with a laptop? So I can have the parameter on my computer if someday the variador broke and i have to install a new one. Thanks
Hello, Great introduction, I'm totally new to vfd's and i have a couple of questions: Is there a way to control the frequency with the wheel in a 'live' way, without the need to press the set button? Can you please explain what the connectors on the rght of the rj45 port (the screw terminal and the white one) Also the 4 screw terminals on the bottom on the left and the mini usb on the top. Thanks!
Hello Teo. Regarding set for speed, i have never been able to alter that, so believe that is the only way. The white terminal is for additional boards that you can add to the drive, i.e ethernet, mobus, can and so on, mainly for communications. The screw terminal is were you would secure the additional board. The mini usb port is for connecting to laptop for use on RF Configurator. Check out the channel for RF configurator video, wary handy tool. And the 4 screw terminals on the bottom if I understood the correct ones are used for DC brake connection. Hope that answers your question.
Hi There. Glad you like the videos. It is to do with your control mode. Check out full manual page 110 onward regarding parameters you need to change to unlock the ones you are after.
I have the same FR-700 and it is showing error E. IHI , Can you help me to remove this error, This happened after the power failure and when the power came back then the lift stoped working,. I did a couple of shutdowns and restart but did not help. Pls, help me out.
Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
Hi Ingus, Thanks for your videos. They've given me a lot of insight into how to better setup my VFDs and get the most out of them. Great job! All best.
Thank you for the video. I’m completely new to VFDs, and I got one of these second hand. The instructions are good, but going back and forth is sometimes confusing. This is a great how to set up guide, wish I’d googled earlier!
great video series . excellent stuff
Omg thanks we appreciate it . Have a great day sir
Great video👍🏾
Thank you!!!
Thank you good sir. This is a big help.
Your wary welcome, Glad it helped.
Awesome video.
Have a question.
I have one of these on a two stage air conditioning unit.
1st stage blower runs at 30hz
2nd stage blower runs at 60hz
When there is no call for blower my vfd will run 20hz constantly.
Can you help me understand that please?
Hi! Great video. I am stuck with getting the motor spin higher than 3 hz. I can tune it on PU btween 0.5 and 3 ish hz but setting to let say 50 it still run around 3 hz. Can't find it online.
Magandang gabe Po maraming salamat po sa magandang Nakita ko Po na tutorial sa iyo laking tolung Po eto sa akin Po masi may kinabet Po Ako na tolad din Po sa inyo na prequincy inverter sa cobior Ng keyampo sana magawa ko na Po siting lang Po Ng inverter Ang kulang thank you Po ulit god bless
Hi, thanks for the video.
Do you have a video where you explain how to download the parameter with a laptop? So I can have the parameter on my computer if someday the variador broke and i have to install a new one. Thanks
Hello, Great introduction, I'm totally new to vfd's and i have a couple of questions:
Is there a way to control the frequency with the wheel in a 'live' way, without the need to press the set button?
Can you please explain what the connectors on the rght of the rj45 port (the screw terminal and the white one)
Also the 4 screw terminals on the bottom on the left and the mini usb on the top.
Thanks!
Hello Teo. Regarding set for speed, i have never been able to alter that, so believe that is the only way. The white terminal is for additional boards that you can add to the drive, i.e ethernet, mobus, can and so on, mainly for communications. The screw terminal is were you would secure the additional board. The mini usb port is for connecting to laptop for use on RF Configurator. Check out the channel for RF configurator video, wary handy tool. And the 4 screw terminals on the bottom if I understood the correct ones are used for DC brake connection. Hope that answers your question.
❤
Very good
Hello sir what to do if vfd gets blinking in run mode while rs485 communication is going on
Hii sir you can tell me push button speed increase and decrease peramiter Mitsubishi E700
I love your video but I'm having a challenge with my drive... It skips from p80 to p82... How do I get that fixed sir?
Hi There. Glad you like the videos. It is to do with your control mode. Check out full manual page 110 onward regarding parameters you need to change to unlock the ones you are after.
How to see the running motor current in drive
Hi sir e700 drive already setting to parameter and communication line also i will start to jog mode and 2 wire mode my thinking is correct
Please check out the 2 wire control video.
My vfd is showing e. Oc1 without motor what can be the problem
PLEASE LET ME KNOW WHY ER6 FAULT IN ABOVE DRIVE
I'm using a d700 3phase inverter... I.e, single phase to 3phase drive
menu EXT cant move to PU, pls help sir
Hi there. Check parameter 79. For it to work it needs to be 0. But be careful, often it is changed for a reason.
How to take backup of vfd drive (mitsubishi)
Hi there. Please check your fr configuration video on my canal, that should give good idea how to do that.
I have the same FR-700 and it is showing error E. IHI ,
Can you help me to remove this error, This happened after the power failure and when the power came back then the lift stoped working,.
I did a couple of shutdowns and restart but did not help.
Pls, help me out.
Hi Mustafa, i cant seam to find this kind of error on Error list.
Eurror 5A?
Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
Hi There, your video is very interesting, pls make some more videos on Error IHI or THT
I have subscribed to your channel already,
My error code E.THT
Hindi