First mistake: Your output straw needs to be wider, the input and output cannot be the same thickness or you've got the same pressure on both ends when the water starts flowing out, and that will do absolutely nothing. Also, the output has to be as close to the bottom as possible, and the container cannot be flexible or it negates any vacuum created by the water flowing out. You also absolutely must have more water flow out at the start to create the vacuum than the amount of water that will be coming in. You have 3 forces working together, atmospheric pressure, vacuum, and gravity. Gravity acts as a constant input of energy in this device.
Noop input straw can be any size, output straw can be any diameter, sholt or long, does nor matter. For this „pump“ to work, the water level in the source must be highervthan the output, then it works - as a siphon.
But bottle se pani nikal ne ka bad air pressure kam ho jata hai, is liye pani ko khich sakta hai lekin air to pani ka niche to nahi a sakta , so I think isiliye pani ko upar ki pipe se khichta hai, lekin kahi lickage nahi hona chahiye, aur bottle se nahi hogi , bottle sikur jayenge, I think hard material se ho sakta hai
the weight of the water in the outflow pipe must be greater than in the inflow pipe. It is necessary to increase the diameter of the outflow pipe and lengthen it and at the end reduce it to the diameter of the inflow pipe, because the water will flow at the same rate as in the inflow pipe
No, you do not want to reduce it to the diameter of the inflow pipe. If you do that you have made the pipe wider on the other end for no reason. The resistance would be the same as if the whole pipe were the same size as the inflow pipe. Think about it this way, if you tried to poop through a straw, it would be difficult. If you made the straw wider on the end that goes in your butt, the poop still has to go through the same size hole on the other end, and so it makes no difference.
You must just have a much bigger water Volume at the output Pipe...only then it might work...so connect a second bottle at the water outlet and fill it additionally with water....
Exacto no funciona lo he probado de muchas maneras y la única que si funciona es dejar el tubo de abajo mas grande, pwro al final por salir mas agua que la que absorbe, se queda vacía dentrp de poco tiempo.
its working at my end, u need to close both pipes open end and remove inlet pipe's opening last.its not again physics water can move from down to up also, just link/connection of water should be created at perfect timings
You have bottle too full & intake submerged. Atmospheric pressure blocking flow. To force water up straw, youd need suction caused by the gravity pulling water. But the suction is blocked by the water being over the top of the yellow straw in the bottle. When you uncapped it pressure/atmospheric pressure released & gravity brought all water to level.
@@ayeecanosa7760 if your imagination is big enough you can apply it in real life situations! like, change the liquid or make it 10 times as big et cetera
Ultimately ... At one point of time the storage will be empty ... Bigger pipe at output means more water going out than the input ... At one point the storage will be empty
@@MaheshYadav-je7lt it will be the same coz the more water going out, the more pressure to suck the water in the input. Unless you have a leak in your bottle that will suck air in.
What if you take the orange straw the outflow and extend it into the reservoir breaking the water tension would it create a circulation if it does create a circulation one could put a turbine at the elbow to create electricity possible
@@apelila081 yeah but when the water started to flow out from orange pipe you can see the air moved inside as it was not fixed, you have to stop the air from moving inside the bottle to make the vacuum work
Energy can be neither be created nor destroyed. We know that. Thats why we make two hole. One output and 1 input. Trying to re used the energy cost in the output to input it but there is a height difference so the out put should be larger that it will become equivalent than it will work
Soon after you filled the water and released your finger, air bubbles entered the bottle from the outlet side. Hence your arrangement was not airtight and hence the result is not conclusive. Please repeat the experiment with complete air tight arrangement and observe the result. Your set up was neat and clean; good.
to make that thing work is all about the right computation of water volume inside the bottle, the right size of bottle, and with a help vacuum plus the right height of the bottle above the ground just to work the law of gravity... to make it simple.. water volume/bottle size, intake pipe/length/size, output pipe/length/size. The last and the most important is you must completely sure that it is air tight, meaning the only way that can past through the bottle with water and past through out is the intake and output pipe.. correct me if Im wrong or if there is missing with my explanation P.S. I made that thing work with the help of science and math and im using it now in my fish tank..
All these non-stop electricity-free pumps won't work without turning bottles upside down, human intervention is needed or in this case, opening the cap. That is what you have the pump for, to push water to climb up to and do its cycle. You cant have just 2 straws or hose connected and expect the water to climb up, go back or be sucked back in to continue the cycle. Those who say this works without any human intervention after setup must do a step by step unedited, unfiltered video because a lot are claiming 'non-stop', that is, until you need to turn the bottles lol.
bro the hight for the water to rise from the source and the width of the bottle is not enough to create the suction and the top yellow straw is spose to be much more higher than the water inside the bottle the water volume is incorrect thats why it dosent work
Outflow water level should be below the reservoir water level, then water will flow irrespective of the diameter of inlet or out let pipe, 👍 this is law of water level. ಇಂಚ ಉಂಡು 👌
भाई, मेने ये एक्सपेरिमेंट कर के देखा हे, और ये चल भी रहा हे, ऊपर वाली पाइप के नीचे तक ही पानी रहना chaiye, पानी और हवा के दबाव से fauntan सही काम कर रहा हे।
Thank you for help and informing us because I also getting try to this experiment so you post this video I thankful to you for do this experiment for us public
the tank shall be bigger so their is more gravitational force acting upon the water molecules.. also when straw will be deep inside.. the water pressure phenomena will act alongside the higher gravitational force due to more molecules
Great Bottle have a Suction. The deeper is the water need more suction. The outlet is higher it need less vacuum. So the water will flow to the deeper level.. You people so fulled with the weight of the water. It's not count... The vacuum measured by cm².. Fake
@@raimundoaquino8202 se observar neste vídeo ele deixou a água quase no nível da capitação ... é preciso estar a cima e a saída fechada ,só liberar depois de tudo certo para acontecer a sucção da água 🤷🏼♀️
First mistake: Your output straw needs to be wider, the input and output cannot be the same thickness or you've got the same pressure on both ends when the water starts flowing out, and that will do absolutely nothing. Also, the output has to be as close to the bottom as possible, and the container cannot be flexible or it negates any vacuum created by the water flowing out. You also absolutely must have more water flow out at the start to create the vacuum than the amount of water that will be coming in. You have 3 forces working together, atmospheric pressure, vacuum, and gravity. Gravity acts as a constant input of energy in this device.
Which colour straw should be wider.. Yellow or orange??
@@yusra1519 The one that is the output, flowing out of the bottle.
If use a bigger pipe for the output and a smaller pipe for the input, is the water coming in enough to replace what is coming out?
No it’s not. That’s what makes it not eternal. But from what I understand it can work for some time
Noop input straw can be any size, output straw can be any diameter, sholt or long, does nor matter.
For this „pump“ to work, the water level in the source must be highervthan the output, then it works - as a siphon.
自作聰明改動了正確的設計。所有成功的大型裝置→1來水使用細喉小管，去水使用粗喉大管（水管粗幼的比例是I比4或I比3 ） 2小小瓶子的水平面蹟不夠大→平面太小了，未能產生足夠的空氣壓力 3水柱的深度太短小了 也是重力水壓不足的原因。4重覆檢查水密封，不可漏氣。5最主要的原因 → 不学無術 偷工減料 自以為是 自作聰明 改動設計。
看到有用中文的太高兴了，我这段时间也在关注，这个不用电的抽水容器的制作，我也试了几次都不成功挺郁闷的，按理说他是可行的，可是我没成功，因为都大多数都不是中文频道，所以弄不懂，其中的问题所在。你能发给我一个正确的制作流程吗？你有视频吗？给我一个你的视频连接好吗？谢谢。
But bottle se pani nikal ne ka bad air pressure kam ho jata hai, is liye pani ko khich sakta hai lekin air to pani ka niche to nahi a sakta , so I think isiliye pani ko upar ki pipe se khichta hai, lekin kahi lickage nahi hona chahiye, aur bottle se nahi hogi , bottle sikur jayenge, I think hard material se ho sakta hai
the weight of the water in the outflow pipe must be greater than in the inflow pipe. It is necessary to increase the diameter of the outflow pipe and lengthen it and at the end reduce it to the diameter of the inflow pipe, because the water will flow at the same rate as in the inflow pipe
Great
No, you do not want to reduce it to the diameter of the inflow pipe. If you do that you have made the pipe wider on the other end for no reason. The resistance would be the same as if the whole pipe were the same size as the inflow pipe. Think about it this way, if you tried to poop through a straw, it would be difficult. If you made the straw wider on the end that goes in your butt, the poop still has to go through the same size hole on the other end, and so it makes no difference.
Why not tighten the lid again once it starts going?
Bcoz he just want to mislead people..😂😂
You must just have a much bigger water Volume at the output Pipe...only then it might work...so connect a second bottle at the water outlet and fill it additionally with water....
It ia real. You can make water Flowing from Above to the top.
Here ia example how to do that.
th-cam.com/users/shortsmtLAapZyMFo?feature=share
Exacto no funciona lo he probado de muchas maneras y la única que si funciona es dejar el tubo de abajo mas grande, pwro al final por salir mas agua que la que absorbe, se queda vacía dentrp de poco tiempo.
its working at my end, u need to close both pipes open end and remove inlet pipe's opening last.its not again physics water can move from down to up also, just link/connection of water should be created at perfect timings
You have bottle too full & intake submerged. Atmospheric pressure blocking flow. To force water up straw, youd need suction caused by the gravity pulling water. But the suction is blocked by the water being over the top of the yellow straw in the bottle. When you uncapped it pressure/atmospheric pressure released & gravity brought all water to level.
Why is it important to study this?
@@ayeecanosa7760 if your imagination is big enough you can apply it in real life situations!
like, change the liquid or make it 10 times as big et cetera
The output pipe must be much longer and bigger than the input only then it will work. And the storage must be big
Ultimately ... At one point of time the storage will be empty ... Bigger pipe at output means more water going out than the input ... At one point the storage will be empty
@@MaheshYadav-je7lt it will be the same coz the more water going out, the more pressure to suck the water in the input. Unless you have a leak in your bottle that will suck air in.
@@antipinoypinoyclub6969 right
Not working
What if you take the orange straw the outflow and extend it into the reservoir breaking the water tension would it create a circulation if it does create a circulation one could put a turbine at the elbow to create electricity possible
you should give it a pressure, the water will flow for you
Sir jaha se pani collect horaha usse niche delivery pipe ko lagana hoga.syphon tank jada bàda hoto acha hoga
U need to keep the water level below the upper straw pipe inside the bottle.
Doesn't work either.
@@apelila081 yeah but when the water started to flow out from orange pipe you can see the air moved inside as it was not fixed, you have to stop the air from moving inside the bottle to make the vacuum work
Energy can be neither be created nor destroyed. We know that. Thats why we make two hole. One output and 1 input. Trying to re used the energy cost in the output to input it but there is a height difference so the out put should be larger that it will become equivalent than it will work
Noop. Size of tubes does not matter at all. No siphon can lift any water to a higher level, regardless of tube sizes.
Soon after you filled the water and released your finger, air bubbles entered the bottle from the outlet side. Hence your arrangement was not airtight and hence the result is not conclusive.
Please repeat the experiment with complete air tight arrangement and observe the result.
Your set up was neat and clean; good.
मैंने ट्राई किया था पूरी बोतल दब जाती है लेकिन पानी नहीं खींच पाता .
nice have a nice dau
Not fake brother i have tried at home with 500 ml water bottle its really
Haa but hawa ke presser se wapas niche ka paani lena chahiye tha yll ?
Holaaa,Lo hice así mismo y no echa agua,no me funciona ,que puedo hacer?
to make that thing work is all about the right computation of water volume inside the bottle, the right size of bottle, and with a help vacuum plus the right height of the bottle above the ground just to work the law of gravity... to make it simple.. water volume/bottle size, intake pipe/length/size, output pipe/length/size. The last and the most important is you must completely sure that it is air tight, meaning the only way that can past through the bottle with water and past through out is the intake and output pipe..
correct me if Im wrong or if there is missing with my explanation
P.S. I made that thing work with the help of science and math and im using it now in my fish tank..
Can you show me how you do it? i really need this kind of thing
i try all what you sed.but it work not.
Can you show us?
All these non-stop electricity-free pumps won't work without turning bottles upside down, human intervention is needed or in this case, opening the cap. That is what you have the pump for, to push water to climb up to and do its cycle. You cant have just 2 straws or hose connected and expect the water to climb up, go back or be sucked back in to continue the cycle. Those who say this works without any human intervention after setup must do a step by step unedited, unfiltered video because a lot are claiming 'non-stop', that is, until you need to turn the bottles lol.
Sir,
I tried it at my place, not working, will you please upload your work. Thanks
Jab bottle me Pani bharo to adha bharo
Aur phir dekho chalta he ya nehni
Me ek video dekh kar ghar pe try Kia tha
Aur achhe chala
bro the hight for the water to rise from the source and the width of the bottle is not enough to create the suction and the top yellow straw is spose to be much more higher than the water inside the bottle the water volume is incorrect thats why it dosent work
Fake nhi.. yellow straw k level k niche pani bharo..
It works..
সারাটা দিন এটার পেছনে লেগে বসে ছিলাম কিছুতেই হচ্ছে না ঠিক তাই আপনার রিয়েল ভিডিও দেখিয়েছেন
আমি ও
not really... u could try and close the vessel inside which the water is draining in such a way that it is vaccumed
The top tube must be on air, not submerged.
Try again!
no it wont work..
If u remove the yellow straw it will work
Super bro. I would have saw this before trying.. One bottle would have saved
It will work for some long. Until the work done to pump the water reaches equal to the work done to fill the tank
Apka sistem tik nahi huy bhi?
Your a blessing! I finally made one after watching all kind of video's, your's was the one that show me.. Thank You
Outflow water level should be below the reservoir water level, then water will flow irrespective of the diameter of inlet or out let pipe, 👍 this is law of water level.
ಇಂಚ ಉಂಡು 👌
There is no "law of water level".
@@darrylkinslow3357 you know what he meant
@@chainjail4834 Did I? Then what did he mean? Oh, you don't even know...
Then why this bottle needed, just piece of tube can do the job
and one more tip... use silicon glass sealant that we use for our aquarium because it is water resistant than the glue gun
Hi
Tendras entrada de aire en las soldaduras. Corrobora esas penetraciones y funciona..
what you did is wrong... the inlet straw must not be submerged to the water...
but it did work on my tank,you just need a bigger volume of water from the thank so that the pipe submerged sucks the water
भाई, मेने ये एक्सपेरिमेंट कर के देखा हे, और ये चल भी रहा हे, ऊपर वाली पाइप के नीचे तक ही पानी रहना chaiye, पानी और हवा के दबाव से fauntan सही काम कर रहा हे।
You broke my heart. But thanks....
very very thanks Main karne hi bala tha lekin appp ki video dekh kar me Bach gaya❤️❤️❤️😲😲😲😲
Thank you for help and informing us because I also getting try to this experiment so you post this video I thankful to you for do this experiment for us public
Thik kaha bhai apne mai bhi ye TH-cam par dekhkar bana raha tha par nahi chala 😭
You need to have biger ouput sothat the pipe has a greater vaccum force to pull enough water from the source
I have done this and actually work
Jinke fountain chal rhe hai,10 minutes ka video bana kr upload kare,Rs 1000 ka inam diya jayega.fake sabit hone pr FIR karai jayegi
May bhi practical kiya hai success nahi hui
Thanks bro pehele menebhi try keya lekin kam nahi hua
Air has to do less work done then water thats why not flowing
Tools?
the tank shall be bigger so their is more gravitational force acting upon the water molecules.. also when straw will be deep inside.. the water pressure phenomena will act alongside the higher gravitational force due to more molecules
Ye bird k water ka accha system h ..free pump to nahi h.
Dapat hindi singaw ang bote kapag at paglagay ng haus sa bottle singaw yan.hindi effective
fake png yan na try kona yan hindi naman totoo
Free energy mill sakti he
This experiment work with big bottle
It is real but we make it air tite
Fake im trying still not working even different size of output and suction
You tell right because this is really fake
good work dear ,thanks a lot
Water level must have below the top side strip
अगर नीसे बर्तन से बॉटल के अंदर एक और पाइप दल दिया जय तो हो जाएगा
doesn't work that really is air pressure block the folw through pipe
Ha moj ha tenks
Great
Bottle have a Suction. The deeper is the water need more suction. The outlet is higher it need less vacuum.
So the water will flow to the deeper level..
You people so fulled with the weight of the water. It's not count... The vacuum measured by cm²..
Fake
hear is problem ,,plastic botol..when the air force for water down to up this time this botol will be loss his thikness,...
Your right it doesn't work any way you try it
आपणे ये झूट दिखाया येत अच्छी बात है।
कुछ लोग चंद पैशेके लिये ऐसी झुटी बात दिखाते है।
No Brother i have create recently and its working Fine
Good job
thank you for your information because I almost did this for a group project😭😭
Very very nice video. your video helps a lot me and my friends. thank you so much keep it up.👌🏻🤗
Trop d'eau dans la bouteil et le bouchon a la place il faut un plastique souple pour faire pompe😉
बोतल के हिसाब से छोटा पाइप इस्तेमाल करो
you need to cut the orange straw.
In flow pipe need to be above the water line. Not below, or on.
Bro Thanks for truth MA to pagal go Gia Tha try Kar Kar ka
App ne thek kaha Bhai Jan me ne b banaya tha no chala
Thank you for letting us know 🙂🙂☺️
He did it wrong
It works i tried it last night he did it wrong
Mil sakte hay, apky project me galti hay
U right bro its dose no suctioning i did try also ❤u
it really works..
بالکل صحیح کہا یہ کام نہیں کرتا ہے
do it reverse it will work
Aap ne galt tareke se tray kiya he bhaiya
Thank you for your video
The biggest mistake you made was to say it doesn't work!!!
Gajb
Pois o meu deu tudo certo ...vc que não vedou os canudos direito
Verdade que o seu funcionou? Estou muito interessado neste tipo de bomba para oxigenar um tanque de peixes.
@@raimundoaquino8202 se observar neste vídeo ele deixou a água quase no nível da capitação ... é preciso estar a cima e a saída fechada ,só liberar depois de tudo certo para acontecer a sucção da água 🤷🏼♀️
Try again it will work
How
You need a low pressure
Must hai or very very nice 👏👏👌👌👍👍
close cap and show after opening cap
Niche ki stro uper ki stro se badi rakho
Dhakkan kholke wapas bandh karte to hojata
Wrong Experiment but fountain energy is also fake think
Concept is good but you've failed
yea fake , i just tried it , not working , but in another models it is
well fone brother
idk who taught you how to build it but thats definetly not how and this experiment does work if you build it right. you have that set up backwards
Thanks you so much
filter water with it sand in bottle