Configuring VoIP Phones in Cisco Packet Tracer
ฝัง
- เผยแพร่เมื่อ 18 ม.ค. 2017
- Do you want to know how to configure VoIP (Voice over IP) phone systems? Have you always wondered how to configure Telephony Services on a router to run VoIP on your networks? Have you wondered how to configure DHCP for your VoIP network?
Take my Cisco CCNA iOS Administration Labs Course for $10.00
www.udemy.com/cisco-ccna-rs-2...
Take my Subnetting - Become a subnet master Course for $10.00 (Best selling online subnetting course)
www.udemy.com/subnetting-beco...
DONT FORGET TO SUBSCRIBE AND LIKE THIS VIDEO!
LIKE US ON FACEBOOK:
/ learntechtraining
For more Courses visit www.learntechtraining.com
Buy the Cisco CCNA RS Complete Study Guide Here: goo.gl/8SpGcN
Buy the Cisco CCNA Voice Study Guide Here:
goo.gl/uy6qoU
![ช่วยพาฉันผ่านเวลา - วสันต์17 [Official MV]](http://i.ytimg.com/vi/HFnntWoqc54/mqdefault.jpg)
I spent an hour on this lab until I came to your video which helped me figure it out in 8 minutes. The lab had the wrong source IP when configuring telephony on the router. SMDH! I was using the data vlan DFG. Thanks a bunch! Great video!!!
Great Job! Thank you for taking the time to make this lesson. I didn't mind the speed as I am able to pause the video and I appreciate you keeping the lessons lean and concise.
Straightforward and informative. I like it was complete and short.
This page is an absolute gold mine
multumim Ana Han! You the best! - From C3buc with love
thanks,
I searched a lot, finally got what i need! Thank you for this video (Y)
It's really amazing and easiest way to get knowledge. For VOICE VLAN. Thanks a lot...
So you were tabbing instead of entering in the command line parts for excluded address and encapsulation i feel so silly haha, very good video!!! thanks so much for helping not only me but my whole classroom to understand better the class of networks and computers :)
You are so fast programming!!! good ability i hope i get like that one day,
good vibes
FYI, when using Packet Tracer, if you hold the control key down when selecting the straight through cable, you will not have to re-select it each time you make a connection.
thanks a lot
Even 5 years later, this comment comes in handy.
Just completed the lab - thank you very much speed was fine for me
This makes everything look pretty simple and easy to understand
Great session and .........speed doesn't matter.
I think you saved my time also. Somebody may take 20-40 minutes(i have no doubt at capabilities of others too, it's the way of teaching) to explain in "SLOW" mode but you explained everything very nicely and smoothly.
Thank you.
Thanks for the video.. the command line or terminal works best for me for sure. Easy to track the moment you get to know the structure.
Huge thanks for this! I wasn't understanding the class I had too clearly but with your example it's making a lot more sense :D
Absolutely amazing video.
Thank you.
Just incase someone is trying out the video in packet tracer and wonder why it is promoting them to configure the MAC address, I learnt from a few people in the comments section that we simply have to plug out the power supply to the phone and plug them in again. Do this twice and wait for the phone to be registered.
Repeat the same procedure for the other ip phones after typing the button 1:n command.
Great video! 👏🏾
Where n is a number of the phone.
If you have three phones like in the video then n can be 1,2 or 3.
this saves me haha.. ive been struggling to find the solution for that configure the ephone MAc address thanks a lot
Very good tutorial. Thanks LearnTech. I subscribed to your channel in under three minutes.
You have earned my subscription with this one bro. Many thanks !
Thank you for the lesson, it was clear and brief, and to the people who complain about the pace, first its a video so you can rewind on the part you miss, plus you should have some basic knowledge on both R&S and voip before executing such labs. Good luck all
Thank you so much for the wonderful comment! I don’t take negative feedback any less than the goods after teaching as long as I have been ive learned that everyone learns differently. Hopefully my work helps to continue educate everyone.
Thank you for another great video. God bless and good luck, Mike
Great video. Simple explanation!
excellent video, easy and quick to learn :D
this is still great ! building my own network that emulates a school district and wanted to get a VOIP phone up and running.
Great job sir. Thank you very much for your time and sharing the knowledge.
Thanks for posting this video!
Many thanks for the video, it really useful to me. Actually I have 2911 and EHWIC ESG, I'm thinking to buy another 2960 switch to more easily configure the system.
Thanks 👍 for sharing this valuable information which I was looking for.
Thank you for the video, appreciate it very much
Thanks a lot for this video.It's very helpull for me. Thx again
If you get the Need to configure ephone MAC address or VM station-Id error, just unplug your ephone as soon as you get the error. Make sure that both of the link lights turn red. You might have to unplug it twice. Once both are red just power your ephone back up and wait for it to register, then move on to the next ephone and repeat this process until you’re done with all three of them.
thank you so much
@@bugraates478 still showing unregistered
How do I configure the mac address pls
i hope to be as savvy as U bro ASAP. that was bomb!!! just subscribed too thanks
thank you very much for this wonderful configuration keep doing
I love this. Thanks.
Very helpful, thanks!!
A very good presentation
Very useful, appreciate it
Thumbs up for training on VoIP configuration step by step with Cisco packet tracer. My question is if you have two or three Cisco switches how do you configure Voip and other vlans on the other switches
Hi Keith! Very Informative video, Can you do QoS configuration next? Thank you very much! more power to you guys!
Great video!
Thank you
A very good presentation
OK! i success ! thank you so much !!
i can run VOIP on my CPTracer
wow nice! thanks very much indeed!
Thank you for sharing sir new supporters here
Really Good Video
thakyou very much. helped me a lot
awesome video
this is very good for me
Thank you
great video
good job
wow awesome, thank you
Nice video.
Thanks bro 😎
thanks! this was a good refresher. I am ccnp certified but I have forgotten the basics...how stupid i am now...even the connection between switch and router with subinterfaces i forgot...i just apply vlan ips to switch and communicate
How long did it take you to study for ccnp before taking the exam.
@@davidharrow9025 I was pretty slow. I took over 2 years to prepare of the 3 modules(routing/switching/troubleshooting)
for some reason, his voice is very satisfying !
what if "switchport voice vlan " command is not available on the switch?
should i configure a trunk for each port where a phone+pc are connected?
greAT STUFF
This part is understandable and clear. i am searching for a video on how to create different subnet for computers. you have created 2 dhcp pools but phones and pc's are getting ip from one dhcp. can you extend this video to show how the pcs will get ip from .10 dhcp
just assigned PC to different vlan instead 10 , and make sure that vlan is part of router DHCP.
Thank's
thanks
You’rewelcome. Check out our new playlist series on Data Encapsulation!
Very nisss splein thanks
Hi. Thanks for the video. Where the phones already set to accept DHCP on the Voice VLAN ?
If I have two phones setup like you’ve instructed, is there a way I can program the buttons on the right of the screen so that they will call the other extension?
I have done as really physical and it works perfectly thanks good work.
i'm following the video and have gotten up to the part where you're configuring vlan 50 as the native vlan. i'm getting an "invalid input" error? not sure why...switchport commands for the other vlans are working perfectly.
figured it out, had to exit config-ephone after each one and go back in and do the command sets.
Hi Mr. Keith. I am attempting to register some phones with CME. Where you have the 2960, I have a 3560 in packet tracer and a 3750 in real equipment. Can you get the telephony-service with a layer 3 switch? My top router is from 2800 series in both packet tracer and the real equipment. Forgot to say. I am not using the router on a stick model.
Hi, I am trying to learn packet tracer and this video has helped me, but can you please slow down as it's quite difficult to follow when it's going quickly. Other then that, very informative!
play back at .75 speed. thats what i did.
Thank you for the amazing tutorial can you please confirm if i can use the same configurations for IP telephone in ISR4331 router.
Great video - am not sure if I missed it , when setting up the vlan do you need to know which ports your using for the phones on the switch?
Yes, you will need to assign those ports to the proper vlans for both data and voice.
During DHCP configuration of the phones, the router is supposed to get the MAC address of each phone. If this fails, you get an error saying to enter the MAC address.
The one required is the VLAN1 MAC you can see placing the mouse over the phone in the Topology.
Another option is to unplug the power on all phones. Plug only one, and wait for it to get the IP address from the router. When the phone register, you should be able to ping the IP of the phone.
When I do this I get "Currently not supported in PT"
3:16 I'm having issues it states error under native under letter a. I've copied the transcript exactly
Can you make a video on calling to a physical phone via VoIP call please
08:29, I also like the Telfany service over Telephony service
Good day i had hard time dealing with telephony service in my packet tracer seems it dosnt have a capability to do configuration for ip phone. Help! what should i do?
But I have a seperate DHCP server for address pools so how do I config options and telephony if i'm not in dhcp?
I think he rushed at the end. "type 7960, button 1:1" what are those, a bit of explanation would clarify that. Overall its short and brief !!!
Hi, first of all thank you so much for this , you just saved my project . Second, I'm having a bit of a problem with the 'switchport native vlan 50' command. It generates an 'invalid command' error. Can you please help?
Use switchport trunk native vlan 50
I have a question. How does the router or a dhcp server know which scope to handout to the dhcp requester. I mean the port had voice vlan and data vlan so initially when the phone boots ups its not tagging any packet so why doesnt the pc get ip from voice vlan scope and the phone from data scope?
Thanks a very nice tutorial
But this pops up when I try to reload the system
"Need to configure ephone mac address or VM station-id"
Just unplug and plug the power cable from the ip phones then retry the button 1:1 command. It should register the ip phones.
@@therealafro_cyzk_bw5281 when i try to do that it says the same thing again
@@jazsoul Do u solve it?
@@bernardolopes1868 nope
You can use auto assign instead of button command
Thanks a lot, your video is very useful . I have a cisco C3900 router. when I type telephony-service it dose`t work. can I configure telephony-service in cisco 3900 router?
So can this now be used to call regular telephone lines or are there additional configs required?
hi thank you but can i get extend voip document and how configer the simulation?
Thank you for this video. I have a packet tracer question. How did you get the gui of the telephone to be so large. Mine are small even if I click zoom. I'm thinking it's because of my screen resolution, but thought I'd ask.
great video what is the button, what is button 1: line 1 and ephone-dn 3? thanks
I get what you're trying to achieve, and definitely get a thumbs up, but for the novice it can be very overwhelming. Slow it down, take your time and explain in a little more detail what you're doing.
Just some constructive feedback is all, other than that, good way to show how to get basic IP Telephony working without using Communications Manager. A lot of people may be asking how you configure DNs that stick to the device. Is there a way in the Cisco IOS to fix a DN to a particular device based on MAC address? Or is that more of a CUCM feature?
+PtDa Fool -- Haha, nice name! Anyway, yes, there's a way to direct which extension a particular phone gets. When you create the 'ephone' section, add 'mac-address
So I'm looking on getting some Cisco phones and can you comment if you can every thing I need to do please?
What happens if you dont set up the encapsulations for the 2811? Will the phones and desktops still work?
hi sir, thanks for the tutorial . but one thing that i dont understand when i dial 1020 from ip phone , the phone is connected by there is no ring there what i mean no sound of ring in the ip phone,, what is wrong with my setting ?
Do the VOIP phones strip out the vlan tags before sending the data to the computers?
Thanks for sharing the video,it was helpfull...but the command are not clear please
Hi. Just a quick question. Will this topology work in the real environment without CUCME Installed on the server?
Hey i want to configure voip but i have 2 router and each router is connected to 2 switch is it possible?
Hi why I'm having problem like Configuring CM List on my packet tracer? Thanks in advance
Can i conect if i have router on a stick setup ?
sorry but what can be done with "need to configure ephone mac address or vm station-id" I followed all the steps in the video
i have the same
nice work but too fast to watch and to understand, still having issue ip phones not connected still and vlan has issues
when i do the trunk i get error
i need help.
what if there are 2 switches, how can i give extension to the phone connected to the other switch? they are getting the ip from dhcp but not the number. i must be missing something. the phones on only 1 switch are getting the extension
Need to configure ephone mac address or VM station-id .....that is the sms that i am receiving after configure ephone 1 and button 1:1 or 1:2 . help
i had same problem like you how you solve it
I also have the same problem. And at the end, my IP-Phone doesn't work, the director-number doesn't even appear on the IP-Phone screen. If you someone find a solution for that issue, please post it. Thanks !
@@chriskelly4466 You need to config the PC ip configuration to DHCP
Big like daca esti aici pentru C3buc
where did you get the port 2000? From the dhcp server?