DSE Training : DSE 4520/4510 how to program from front panel without laptop | dse configuration
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2024
- DSE Training : DSE 4520/4510 how to program from front panel without laptop | dse configuration
BUY here : amzn.to/3PfSIae
DSE7420 MKII Original - Made in UK |
BUY here : amzn.to/3P0AgSI
DSE4520 MKII Auto Mains (Utility) Failure Control Module
BUY here : amzn.to/3R5p2iu
New Original Deep Sea DSE3110 Generator Controller DSE 3110 Diesel Generator Genset Controller
BUY HERE : amzn.to/3sJBEBM
Generator Controller, DSE6120 Deep Sea Electronic Generator Controller
BUY here : amzn.to/3sGY1b4
Original Deep Sea Controller DSE7320 Generator Genset Auto Start Control Module New Electronics
about video :
here are the steps on how to manually program a DSE 4520 controller through the front panel:
Make sure that the DSE 4520 is turned off.
Press and hold the Menu button until the Programming menu appears.
Use the Up and Down buttons to select the parameter that you want to program.
Use the Enter button to change the value of the parameter.
Repeat steps 3 and 4 for all of the parameters that you want to program.
Press and hold the Menu button to exit the programming menu.
Turn on the DSE 4520.
The changes that you made will be saved to the DSE 4520's memory.
Here are some of the parameters that you can program on a DSE 4520:
Start and stop settings
Battery monitoring settings
Load control settings
Fault reporting settings
For more information on how to program a DSE 4520, please refer to the DSE 4520 Operator Manual.
Here are some additional tips for programming a DSE 4520:
Be careful not to change any parameters that you are not familiar with.
If you make a mistake, you can always restore the DSE 4520 to its factory settings by pressing and holding the Reset button for 10 seconds.
I hope this has been helpful. If you have any questions, please leave a comment below.
@DieselGeneratortraining
#dse4510 #configuration #dsetraining
Other videos of DSE 45xx series :
dse 4510/4520 electrical wiring diagram explained
• Dse 4510/4520 wiring d...
dse 4510/4520 wiring diagram explained Hindi Urdu
Dse 4510/4520 laptop configuration
• Dse 4510/4520 pc suite... - วิทยาศาสตร์และเทคโนโลยี
th-cam.com/video/yBtMaPMOXbE/w-d-xo.html
Very informative thx engenior
Thank you for the help!
Nice video sir, this controller they have cooldown for stopping the genset, thanks
Yes, you are right
HI please can you show me how to remove the due service light.
thank you so much for this lessons. I have a 20kva diesel generator but does not have a DSG controller, it uses a key switch.. How can I add a DSG controller to the generator
Glad it helped
THANKS FOR WHAT EXACTLY ? ALL THE videos is that he reads whats on the screen like any 10 yo can do
please how do I enable fuel level on this panel?
Fuel solonoide ko dg off krwany k liye Kon c setting use krni ho gi
Where can I connect the two sensor wires for remote start from my ats panel to dse4520 controller?
Hello do you change parameters while generator is running?
Which number connect to ats? In eicher already I see remote wire connecting so where i connect help me plz
HI Can you explain DSE 9130 and HMI 211 connected with PCC 1302
Me also want this ....
When load high need second generator automatic on off & synchronized
Me too want a video about PCC1302 and HMI211
Tnk u
please how do i configure my 4510 for a 40kva generator. i am particular about the ampere settings.
Thank you so much
You're most welcome
My office generator with the DSE control panel is experiencing a fault. The stop button is blinking continuously and generator can't start. How can i clear or reset it
Thank you from Ethiopia. I faced a problem that the generator shuts down in 10 seconds by displaying low oil pressure alarm on the screen. Oil is changed and its level is okay, oil viscosity is okay, oil pressure sendor is okay. The generator is new, run only 65 hours. The generator type is perkins 45KVA and the controller is DSE4520. Please help me!
Thank you for your help in advance!!!
We had same issue with a 150kVA Perkin generator in Pakistan at around 1050 hrs. We changed the oil pressure sensor but it didn't fix the issue. We replaced this control panel with a new unit, and the issue resolved.
Sign from 931 to 940 shows and generator not started plz guide
What is the meaning of service alarm
Hello, my 45KVa generator shows warning alarm signal on the screen and can’t start
how do you read a fault on the controller
How to reset oil filter maintain alarm
Ok sir thanks super 🎉 🎉🎉
What can i do if it isunable to start
How to set a remote start on input 14
Thanks you bro
Nice
Thanks
How I can rest the engine hours in the madeul
Why u need to reset brother
As wr wb
Does this Control panel (DSE4520) has password??
From factory no password
Hi. Do I connect Gen start signal from Inverter to Digital Input 1 and 14? Is any programming required?
Hi, have you found the way to do it pls. could you share pls
I want to know how to adjust the running hours of the generator
Without laptop
10 kva 3 phase gen can change only 1 phase use without unbalance load
Deep see 4520 Not show u hz metr
Salf cutoff prgram
Sir Mary paas 4520 lga Howa Hy lakin amp show ni ho rha plz help me
Three phase generator hai ya single aur current transfer lagay huway hai k nahi 😐
@@DieselGeneratortraining 3 fhase hy transfer ni lgya howa
CT laganay hongay phir current show hoga
@@DieselGeneratortraining ct aue conacshon bhai kr diy han fir bhi ni àaya
OK wait karain ek video banata ho phir ajai ga
How to clear error code on dsc4510?
How to check the continue on in automode
Hi
My Gernater start than 5 secend off
My generator is getting off in 5 sec when i on the generator, and again itself automatically starts the generator and getting off.. Like a cycle.. Please help me
Please always share in details what is the engine ,alternator controller n alarm on screen
@@DieselGeneratortraining it's a 4510 MKll controller and engine is Leroy's somrey
Check battry voltage may be battry voltage less than 12 v
Hy
Mashallah
G