ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2024
- This video demonstrates the simple way to control the direction of a DC motor which in this case a 12V car power window. Two relays were used to build the required circuit and in this video, a 2-channel RF wireless remote control relay module was the perfect choice to do that. The connection is so simple; everybody with or without basic electronic knowledge can build the circuit in minutes and use it right away. This video intends to give some basic idea on building a bidirectional motor control circuit and you can apply it in your own project/application.
For those who are having trouble catching up the connection for 2-direction motor control in the video, you may refer to this diagram: goo.gl/Fnsf4B. Just ignore the Arduino side as the relays themselves will be activated through button click. However, if you in case to build Arduino controlled 2-direction motor control, then this may be the diagram you are looking for.
The Arduino code to make the motor run forward and backward continuously with 2 seconds of duty cycle: goo.gl/iN7sfr.
Circuit diagram: goo.gl/rxqDrg.
Demonstration video: • DC Motor Forward/Rever... .
The Arduino code to make the motor interact with input from serial communication: goo.gl/ZqecCP.
Circuit diagram: goo.gl/u5AQKg.
(Updated on 26 Feb 2019): For 8 channel relay module: goo.gl/admrPB (pin connections are described in the code introduction).
(New - Updated on 29 November 2017) The Arduino code to make the motor interact with input from serial communication + manual push buttons: goo.gl/iPjDhZ, with help of circuit diagram: goo.gl/fLeJpF.
For those who don't want Arduino in the diagram, refer this circuit: goo.gl/kjjoKU, with truth table included.
(Updated on 1 March 2018) For those who are interested to use limit switch in the circuit (such as for linear actuator motor control), refer this circuit: goo.gl/C5ATjB for LOCAL controlled single limit switch version and this circuit: goo.gl/83mynM for LOCAL controlled double limit switch version. And for REMOTE controlled double limit switch version, see here: goo.gl/gZVRp2. Hope that helps :)
(Updated on 29 November 2018): If you want to make the motor turns forward until a limit switch is pressed, then wait for let say 1 hour before going reverse until another limit switch is found, then wait 1 hour again and repeat the process again like more or less shown in this video: • Forward/Reverse Direct... , here is the code: goo.gl/dnHLkR.
B/G Music: "Dalam Air Terpandang Wajah" - Legendary Tan SRi P Ramlee
Thanx so much
Your explanation was perfect Sir!
Thank so much Sir I'm have trouble putting this code unto my sketch, what is the proper way to put a title to this code so the board will recognize it , I'm so anxious to get back controlling my renovated 4wheels robot, thank you so much for your patience, I'm 86 year old and a bit slow in understanding all of this new stuff sometimes Jerry
can i do the same with a roller shutter?
As long as it uses DC motor, the answer is yes.
Nudge Me can use ac to dc converter is it? Btw mane nak beli ni rf bos? Tq reply
Can use AC to DC converter for the receiver unit only, not for the motor. The motor always needs to be DC.
did that years ago also made the motor to be slower or faster, its not rocket science
Thankyou!!
You are the best. I have been finding out how to do 2 direction on a RC relay switch and you are the only one that did it and explain it perfectly with diagrams. Thank you very much. Keep up the good work!
+Ethan Chang Thank you very much! I'm very pleased to hear that.
Complimenti veramente bravo ma se dovrei i mettere 2 finecorsa microswitch alla scheda per il motorino come faccio? ho provato in tanti modi, ma se avrei uno schema forse ce la potrei fare grazie
Can u make it to the smalliest relay
Bhai video chahe lambi ho Jaye lekin voice and video speed slow rakha karo
Friend, please, you're so kind, you can give me an electrical plan of the last function where the direction of the engine is changed... I'm from Colombia, here the language is Spanish, that's why I need a translator
pause and play, pause and play, pause and play, pause and play, pause and play, all day LoLz
thanku bro
Can you show this but with a linear actuator and a powerbank with usb cables 😁
I want a diy so i can make it at home.
hello How to control dpdt with rf 4-channel 433mhz wireless remote control
It's so informational, i'm using 2 channel modul (not remote control) and linear actuator for auto open and close my motorcycle seat.
Great video!!! Thank you!!
Kl mau di tambah kan limit switch wiring diagram nya ada Gan..🙏🙏🙏
Mau tanya dong bang..
Ini buat pake dinamo motor listrik bisa ga?
Hi
Can u write down the link to purchase this exact board please?. Thx
Hi, I bought the remote controller set here: goo.gl/JvQfTk
Forgi to let me
Can someone please write it down where to place the wires on a relay module to make a motor go back and forth
Rubbish to quickly I can’t fallow
Thank u so much..I was struggling with wiring for 5 days and i found your video and u saved me.Thanks again.!
You welcome, shen!
Itu kabel namanya apa ya? Yg di konekkin ke modul
Boss, boleh draw diagram dia tak?
apakah relay di ganti dengan yg 6v bisa ??
Awesome video! Keep up the good work!!
Kalo d kasih speed control bisa ngga gan
bummer....video is sped up so much and wires not always visible so can't tell what is really going on. is a simple wiring diagram available
Hello, you can refer to this line in the video description above:
"For those who are having trouble catching up the connection for 2-direction motor control in the video, you may refer to this diagram: goo.gl/Fnsf4B. Just ignore the Arduino side as the relays themselves will be activated through button click. However, if you in case to build Arduino controlled 2-direction motor control, then this may be the diagram you are looking for."
Hi sir please I want 4channel connection
How about 4 channel with 2 DC motor
Can u send me diagram off connection to motor with cut switch plz sir
Sir can I use micro cut switch in cut pont to project etc
how to add end of course to this project?
I want urjent connection sir please
bang kalo buat setater motor bisa gak
Car lock unlock me use kar sakte hein 🤔
Link pembelian mana??
hello how are you connecting the cables for the motor to raise
Teşekkürler
i luv background song
Tq helpfull for me👍
I owe you one man. This has been a very useful video. Thank you!
Sir your link cannot open
I want that kit buying like
Can limit switches be used with this board?
Whats the range on that system
I need this circut
Any luck. I need it also
Beli dmn bang?
Hi,i have bought two but it is disturbing each other,how i want to do it,tq
If the frequency is same the interference will happen but remote A should not be controlling the receiver B. Try to pair again each of the remote controller with the correct receiver. Refer the instruction manual how to do that, something using the push button on the receiver.
Pakai dinamo apa bang & brp rpm
Ini power window motor, voltan 12V
@@nudgeme4844 bisa bolak balik ya?
Hi sir i want to buy Full kit for my project
Just found this amazing item on AliExpress. Check it out! MYR2.35 95％ Off | GERMA 433Mhz Universal Wireless Remote Control Switch DC 12V 2CH RF Relay Receiver Module + 2 CH RF 433 Mhz Remote Transmitter
a.aliexpress.com/_mOfg7n8
Where can I buy this 2 chanel RF controller..?? I can find something similar at the ebay but not exactly the same.
Hello, you may try searching it on aliexpress.com
many 2 ch rf controller but none with jumpers..
Tanya gan......
Itu bekerja di frekwensi radio 433Mhz ya.....
Lha seandainya transmiter / remot di gantikan pake radio ht uhf dengan frekwensi yang sama 433Mhz apakah bisa...?
Ye arcat kahan sy mly ga jnab
Itu arduino kah
Hi everyone,
I would like to be able to receive the signal from a controller with an HCS301 (MICROCHIP KeeLoq) in the transmitter and with a PICxxx or an ATMELxxx in the receiver.
There is a library for ARDUINO about receiving
hello, I want this 2-CH RF Wireless RC Relay, but I want for 240V can I find it somewhere?
Hi, you can find it on AliExpress. Example: tiny.cc/f7fzcz
How much it's rpm
Blooody helll my brother...!!! I am searching exactly this solution, but i did not know that i can do this short impuls reverse polarity with two receivers with SPST relays...!?
Thank you a looot...!!!!
You saved me...!!!!
+Evil Max You are welcome :)
Bhai plz I need ur help
I have dual relay 12v model kr1202-4. And 1 remote. i reset original remote by presing a+b buttons and my remote not work anymore, please help me?! What should I do....
Please, Do not ignore my question:
How to use limit switch, arduino and relay with high current 12V DC motor?
I want to use 12v dc wiper motor to power a heavy duty DIY linear actuator.
The actuator move forward and reverse and must stop at a precise posistion.
I can control the motor manually with 6 pin (forward/reverse/stop) button, but it will not stop in the wanted position.
I cannot use limit switches directly to stop the motor because the motor is full loaded and run with more than 10amp to 15amp which will burn the micro limit switches.
The question is:
I want to use the same thing in this video but with adding limit switches and using simple 6 pin (forward/reverse/stop) button without any remote control, I mean I will click manually on the go left button, the actuator will move left and will stop automaticaly when reaching the left limit switch, I will also click manually on go right button, the actuator will move right and stop when reaching the ight limit switch.
I am tottaly a beginner, but I think that the motor will be powered with 12v/20amp power supply, and the limit switches will take current from the arduino so they will not be damaged. (Please correct me if I am wrong).
Please, let me knwo if that is possible, if so, how to do it.
I will be glad if explain that to me and give a diagram or a video if you please.
Thank you very much.
Thank you. Could you please share the circuit diagram of the connection?
Hi nudge me, i wired exactly the same way as you did, but the wires connecting NO/NO, NC/NC keep burning out, tried three times same thing , luckily the unit didnt burn, any ideas what could be wrong.
Hi, try to use thicker wires than the ones I used in the video as I used those thin wires just for demo only. And before that, it is worth to test out your motor first to tell it is working or not. Connect both terminals of your motor directly to battery terminals and see either it can turn to one side and switch terminal to turn to another direction. Hope this helps.
@@nudgeme4844 Thanks for the reply, Cheers mate, will try using thicker wires, i am also using a window motor which is in working order like your one.
You are welcome :)
can i know the wiring diagram?
hello can i know where do you buy the transmitter? im from malaysia
Pozdrav, čuli smo se pred 3 godine, i bez vaše pomoći nebi tako brzo instalirao sklop. Sad trebam e.maill adresu za jedno pitanje ali bi poslao i sliku . Hvala
I need the same thing but no rf ...I need wifi controller ..for door motor same as yours an 2 direction control....is the same way to connect??can you recommend one with wifi 2 Chanel...thanks..in amazon is possible...
Muito bom 👍👈 sucesso aí família 🤝
Obrigado 😁
AASAN TRIKA BTAYEN
Helpful
Hi sir i need your help
Hi all. Please help me I don't know what to do. There is such an assembly through a 4-channel relay and through the switch pedals to the motors. The remote control works great. The pedal in one direction also works fine. And the Problem is that when you press the pedal so that the motor spins in the opposite direction (reverse), there is a short circuit in the relay area and even one relay has already burned out. As an option, I thought to put a switch between the relay and the pedals, that is, either turn the motor through the pedals, or through the remote control, but I would like it without a switch, that is, when I wanted to press the bullet or the pedal. Please help me how to fix this.
Well damn if y'all are really wanting to make one buy a pulse width modulator amazon 20 bucks flip of switch reverses polarity and you can go as slow or fast as you like
Hola a tod@s,
Me gustaría poder recibir la señal de un mando con un HCS301 (KeeLoq de MICROCHIP) en el emisor y con un PICxxx o un ATMELxxx en el receptor.
Hay una librería para ARDUINO sobre recibir la señal de un HCS301 y otra para emitir la señal de un HCS301, pero no lo encuentro... sigo a la búsqueda.
Un saludo a todos
Plzz give link to order remote control circuit
Thanks bro
Great stuff. Thank you. God Bless.
You are most welcome 🤗
Would this work for a remote for my motocaddy digital s1??????
Kha se ho bhai appp
can we use both limit switch and push button
Yes. Refer here: goo.gl/83mynM
Nice sir
Bisa ga itu di tambah jaraknya pkai remot kontrol 3km
Yo I have a 12v 4channel..mine isnt working..av tried all I can
Did you follow all the steps I showed in the video?
@@nudgeme4844 yes I did..mine is a 4channel relay..can you give me a wiring diagram for forward and reverse for a single motor
@@nudgeme4844 I need it urgently for a project..is it possible I utilize only 2 of 4channels for forward and reverse?
Super
Ciao, mi sono iscritto al tuo canale, seguendo il tuo video ho fatto pure io questo progetto, ma voglio aggiungere un regolatore di velocità mi puoi fare uno schema di come collegare un regolatore di velocità? Per fare girare più piano il motore? Grazie.
Bg kalo di buat ke dinamo power window , biar tombol A ( mutar ke kiri ) truss tombol B ( mutar ke kanan ) caranya gimana ya untuk modul 1Ch
Hi thanks for this video it's very helpful can you please explain to me how to connect 2 limit switches because I want to use this to power a wiper motor to move a sliding gate thank you
Hii frnd... i m doing ME diploma in malvan.. i m doing auto sliding gate... have u done it?? ... so plzzz help me
@@rohitparab6614 yeah I did it I connected it to 2 limit switches and I connected a reciver to open it remotely
@@suzukisamurai9362 can u give me circuit diagram.. and what are components u used... plzzz sir.. i need ur help
9423925956 my wp no.
Hi I need to connect this to my garage switch how do I connect it ?
What is the exact module that you have been used, I have found some on AliExpress, but i am not sure that they are the same as one shown in this video
I want to do this setup but instead of using a remote control I want to use a 12volt power trigger. Is there a way to do that with this? Or do I need a different controller?
I wired a manual switch to a linear reversible motor then added this remote but my manual switch burn out immediately. Is there a way to use both ( wireless and manual switch) ? Maybe install diodes?
can we use 4 channel relay board on momentary mode to run two motors with reverse control??
Can two relays be turned on at the same time in the monetary mode??
please answer.
Hii sir... your provided website for circuit diagram of two directional motor control is not working or it shows webpage is not available... plzzz give a circuit dia.
Good video bro.. Anyway nak tanya kalau nak set kan power window motor tu bergerak beberapa sudut darjah dia boleh tak? contoh nya CW 90' lepastu CCW 90' pulak..
Thank you so much. Please next time please with sketch/ plan.
But this is what I search thank you
Hi sir how to put limit switch on this project may I request diagram please..thanks
hi. mi reciver stop working. The blue led indicator not turn on any more. What could be wrong?
assalamualaikum en, boleh saya hubungi en ? untuk bertanya lebih lanjut..
Please give us the links to buy the motor and relay modules
Gui em may cái
Rất hân hạnh được giúp đỡ bạn
Too fast and jerky to follow. please slow down.