Уже третий сезон убираю снег с помощью отвала и снегоуборщика. 1. Отвал у меня тоже ворочается вправо, влево , но на один бок убирать гемор(очень медленно, 48 раз проход по одному месту).2- Сделал отвал похожий на ковш: увеличил вдвое высоту(такой же как на видео стал) и приварил боковины. Реально быстро и эффективно грести снег только прямо( но сразу скажу, что усилий приходится прилагать совсем не мало, сам мотоблок не поедет, буксует , не знаю как на гусиницах). Сгребаешь в большие кучи, а потом либо меняешь отвал на насадку-снегоуборщик, если снег еще не слежался (около половины поможет перекидать, потом все равно лопата), либо сразу лопату в зубы и вперед - пахать. 3. Одна насадка-снегоуборщик тоже не вариант( желателен полный штиль, снег 20 см, не сырой) . Но лучший и верный друг все равно ЛОПАТА. При любых раскладах работу заканчиваешь с ее помощью. Зато тренировочка еще та! И главное: вспотел, спина начала подмерзать, иди и переоденься в сухое. Тогда труд на пользу.
MIO standard Osjek, HONDA. Odlicni motokultivatori, a ideja ti super i ne kosta puno, jer ima i kupiti otiginal... da nije hladno odmah bi iskopirao ideju jer imam isti. Bravo. Pozdrav iz Srbije!
Excellent build! Just one bit of advice. If you were to put more of a curve on the blade it would get under the snow and roll it off to the side easier.
Great build.. Few things i saw.. Your mount braket should have a cross support in the triangle . you need a 220V welder but as this is a walk behind it should be good.. Plasma cutters are awesome as well.. also a strip of steel in front of your rubber cutting edge would strengthen as well... excellent build though
A nice build. I wish I could weld like that and may soon learn how to. Your device reminded me of a plow my father built many years ago and attached to a Standard Twin tractor. If you're interested there are several videos of Standard Twins on TH-cam. it's a smaller garden tractor with large wheels on the front and on my dad's version smaller wheels on the back. I've used it for many years to plow snow. However, even though it is much heavier than your tiller it was still difficult to use with heavy or deep snow. Having the blade angled like that pushes the machine to the side quite easily. And with the blade perpendicular to the axis of travel simply not enough traction. Even with chains on the large tires, probably 40 inch tall and weighing in the neighborhood of 150-200 lbs each ( I can barely stand one up vertically from a laying on the ground position. My dad added lead weights to each tire.) and the added weight of the tractor itself it does not have the ability to push a lot of wet heavy or deep snow. Even though there is probably in the neighborhood of, I suspect, at least 500 lbs distributed over the two front tires that drive it. It works though for lighter snowfalls! Well, worked, the motor finally gave up. I'm guessing that you have found that it's not very effective for anything other than light to moderate dry fluffy snow plowing. You should have contacted me before you built it! I could have cautioned you. But then you wouldn't have had the fun of building and testing it. Again, nice build.
Nice work ! Watch your neighbors for when they put gas grills out for garbage - those stainless steel lids are Great for making snow plows for; tillers, and even in front of snow blowers for light snow & slush. (make sure your plow will clear augers - if used accidentally. 😉
Your idea is very good! Maybe you can improve your device, for example, you can place two bags of sand on both sides of the cultivator to make it heavier, then the wheels of the cultivator will not slip. Thank you for this great idea!
Well Done. A shorter height blade and more weight over tires might help. I made a similar pusher that attaches to the front of the rear half of a snowblower.
He made something for little money that proves the concept. He used various tools, while making the plow... a reward unto itself. What did you make, today?
Might uses this idea on my snowblower, when the snow is slushy and it clogs up the snowblower.. use the power of the six-speed snowblower to push the heavy slushy snow off the driveway, convert it into a snow plow. Maybe just bolt on a metal snow shovel blade. ❄️🤔
Cool idea. 1. Thinking ... hmmmmm wonder if I could do that with my tiller. 2. Rear Tiller ... I could just remove the tines in the winter. 3. Would have to find some scrap steel and learn to weld. 4. Wonder could the drive wheels be slowed down? Or could I find tire chains for grip hmmmmm. Wondering .... Why something like this doesn't exist today. You buy a rototiller and it's used, what at most, twice a hear .. To prep the garden and to end the garden ..... It should have a mower attachment / and this a snow pushing attachment or even blower.
Imam jedan savjet za tebe pošto se baviš sa metalom otiđi ma tečaj za tokara i zavarivača pa si kupi neki manji tokarski stroj i odlican video poz iz Jastrebarskog Čeglje: )❤💪
Works great for that 1/2" of snow you get twice a year I bet. Sorry, not trying to be mean, this is very creative. It'd be much better on something a little more substantial though like an ATV with snow tires or chains. Cheers from the north east.
First time seeing me and you're very talented yes you can buy it for cheever lady but doing it yourself that's a challenge and apparently you like a good challenge keep up the good work
As a tin knocker there is a better way to do that roll on the metal. FIY in the future most hvac shops would have let you just roll it on one of their machines , but if not make a jig. It’s way easier
انت انسان مبدع .. لا بد اختراعاتك تتحول الى مشاريع .. وتأخذ نسبة ارباح منها تحياتي متابع عربي
Bravoo.majstore svaka cast
Уже третий сезон убираю снег с помощью отвала и снегоуборщика. 1. Отвал у меня тоже ворочается вправо, влево , но на один бок убирать гемор(очень медленно, 48 раз проход по одному месту).2- Сделал отвал похожий на ковш: увеличил вдвое высоту(такой же как на видео стал) и приварил боковины. Реально быстро и эффективно грести снег только прямо( но сразу скажу, что усилий приходится прилагать совсем не мало, сам мотоблок не поедет, буксует , не знаю как на гусиницах). Сгребаешь в большие кучи, а потом либо меняешь отвал на насадку-снегоуборщик, если снег еще не слежался (около половины поможет перекидать, потом все равно лопата), либо сразу лопату в зубы и вперед - пахать. 3. Одна насадка-снегоуборщик тоже не вариант( желателен полный штиль, снег 20 см, не сырой) . Но лучший и верный друг все равно ЛОПАТА. При любых раскладах работу заканчиваешь с ее помощью. Зато тренировочка еще та! И главное: вспотел, спина начала подмерзать, иди и переоденься в сухое. Тогда труд на пользу.
Nice to see a young man welding and fabricating!
Odlicna stvar samo tako nastavi poz brate moj 👍👍👍🔥
MIO standard Osjek, HONDA. Odlicni motokultivatori, a ideja ti super i ne kosta puno, jer ima i kupiti otiginal... da nije hladno odmah bi iskopirao ideju jer imam isti. Bravo. Pozdrav iz Srbije!
ovo je originalni hondin motokultivator ali imao sam i mio standart f430 tak nest :D Taj je vukoooo ko lud :D
hehehe poz iz Hrvatske ;)
620y 😀 Jel MIO ne proizvodi vise motokultivatore?
Odlicno samo produzi tako, pozdrav iz Makedonije ;)
poz iz Hrv
To se čekalo.. Čitaš mi misli legendo ❤
hehehe
Excellent build! Just one bit of advice. If you were to put more of a curve on the blade it would get under the snow and roll it off to the side easier.
Great build.. Few things i saw.. Your mount braket should have a cross support in the triangle .
you need a 220V welder but as this is a walk behind it should be good.. Plasma cutters are awesome as well..
also a strip of steel in front of your rubber cutting edge would strengthen as well...
excellent build though
Cool little snow plow that was good idea
A nice build. I wish I could weld like that and may soon learn how to.
Your device reminded me of a plow my father built many years ago and attached to a Standard Twin tractor. If you're interested there are several videos of Standard Twins on TH-cam. it's a smaller garden tractor with large wheels on the front and on my dad's version smaller wheels on the back.
I've used it for many years to plow snow. However, even though it is much heavier than your tiller it was still difficult to use with heavy or deep snow. Having the blade angled like that pushes the machine to the side quite easily. And with the blade perpendicular to the axis of travel simply not enough traction. Even with chains on the large tires, probably 40 inch tall and weighing in the neighborhood of 150-200 lbs each ( I can barely stand one up vertically from a laying on the ground position. My dad added lead weights to each tire.) and the added weight of the tractor itself it does not have the ability to push a lot of wet heavy or deep snow. Even though there is probably in the neighborhood of, I suspect, at least 500 lbs distributed over the two front tires that drive it. It works though for lighter snowfalls! Well, worked, the motor finally gave up.
I'm guessing that you have found that it's not very effective for anything other than light to moderate dry fluffy snow plowing. You should have contacted me before you built it! I could have cautioned you. But then you wouldn't have had the fun of building and testing it.
Again, nice build.
Damn. I'm tired just watching him make that. Genius at work!
Young fella, that's some impressive fabrication skills, and a well done vid.
Somewhat easyer than the shovel, a good job jobbed.
Damn dude..... That looks like more work than just shoveling
Exactly, well said.
Svaka čast majstore. Super stvar. Možda samo ne može na brdovitom terenu.👍👍👍 Samo još da napraviš lance za kultivator i ekstra.
Daa obavezno neke lance i togove trebam stavit ;)
Super video and music. Thanks
Good one and no snow on a windy day blowing all over you when you have to go against the wind 💨⚒🛠👍
Nice work ! Watch your neighbors for when they put gas grills out for garbage - those stainless steel lids are Great for making snow plows for; tillers, and even in front of snow blowers for light snow & slush. (make sure your plow will clear augers - if used accidentally. 😉
Your idea is very good! Maybe you can improve your device, for example, you can place two bags of sand on both sides of the cultivator to make it heavier, then the wheels of the cultivator will not slip. Thank you for this great idea!
'
Predobra ideja!😀😀
This guy paid attention in shop class! Nice job.
It's working perfect, well done
Jak widać taki motorek można do różnych robót wykorzystać 👍
You are the best doctor👍♥️
Nice job, as long as you have the right equipment. 👍👍👍👍
Svaka ćast. Imamo isti hoby
;)
Well Done. A shorter height blade and more weight over tires might help. I made a similar pusher that attaches to the front of the rear half of a snowblower.
Odlicna,vido pozz sam nastavi brate
He made something for little money that proves the concept. He used various tools, while making the plow... a reward unto itself. What did you make, today?
I used to have a Bolens yard tractor which did the same thing before I got a snow blower.
9:34 Why didn't he just buy shorter bolts?
@Eric N for short bolts you need to go far :)))
Nice work👍☺
За идею 👍
Ну много минусов, всё таки лучше ручной снегоуборочной машины ни чего пока нет.
Svaka čast bratee
Sve odlično, jedino je kultivator pre lagani
Good Design!! Excellent Job.
imas ti potencijal svaka cast majstor
Good creativity ! Congratulations bro !
Might uses this idea on my snowblower, when the snow is slushy and it clogs up the snowblower.. use the power of the six-speed snowblower to push the heavy slushy snow off the driveway, convert it into a snow plow. Maybe just bolt on a metal snow shovel blade. ❄️🤔
A real professional indeed. Wish I could buy one.
Put it on a riding mower or atv. I hate snowblowers almost as much as snow shovels. They're almost as much work..
A rear v blade would be great, no fishtailing, plus if your handles flipped over and you reversed, now your v blade becomes a v scoop. 😊 good luck 🤞
Svaka cast
Jos si napravis gusjenica i ima da ide ko metak 😁😁 poz
heheh da daa
nice work mate smart idea!!
Респект!!!👍👍👍
Slijedeče Vodena pumpa od trimera☺
agahahaha
Once again...you have done it again...another great idea..great build...great project....very creative...keep those videos coming !
Odlična ideja hvala ti
Hmm, hardening the mold board behind the cutting edge with weld. That's pretty slick. Nice work!
Cool idea.
1. Thinking ... hmmmmm wonder if I could do that with my tiller.
2. Rear Tiller ... I could just remove the tines in the winter.
3. Would have to find some scrap steel and learn to weld.
4. Wonder could the drive wheels be slowed down? Or could I find tire chains for grip hmmmmm.
Wondering ....
Why something like this doesn't exist today. You buy a rototiller and it's used, what at most, twice a hear .. To prep the garden and to end the garden .....
It should have a mower attachment / and this a snow pushing attachment or even blower.
Cool idea, but a snowblower would work a lot better 🤷♀️
Svaka cast majstore :D
:D
Imam jedan savjet za tebe pošto se baviš sa metalom otiđi ma tečaj za tokara i zavarivača pa si kupi neki manji tokarski stroj i odlican video poz iz Jastrebarskog Čeglje: )❤💪
Planiram daa :D
I dnt know what say. You are amazing. Wow I ❤️ your video 👍
Works great for that 1/2" of snow you get twice a year I bet. Sorry, not trying to be mean, this is very creative. It'd be much better on something a little more substantial though like an ATV with snow tires or chains. Cheers from the north east.
Man you sometining else♥️
Pozdrav from Chicago
Nice. But all that work! I've bought several plows like that for $40, commercially made, more heavy duty.
Great work Dr, also luv your bike, ♥♡♥
PA STA RECI ? BRAVO !
Good idea, adding weight to the wheels would help.
If its a wet heavy snow like that, that thing is mainly useless without any real weight added to the machine
Ja reko ti neki stranac svaka cast
hahaha hvala punoo
Idei geniale! Bravo!👍👍👍
Small set of tire chains an you got it kid! Nice!
Laonoa😘😘
Bolje bi bilo raditi ovo na imt 539. Svaka ti čast
Mozda budee :D
First time seeing me and you're very talented yes you can buy it for cheever lady but doing it yourself that's a challenge and apparently you like a good challenge keep up the good work
Молодец. Требуются небольшие доработки, но неплохо. Со сваркой потренируйся.
Kupio sam kosilicu od 3hp, pa sad ne znam koji benzin da sipam, mješavinu ili cist benzin, sta mi ti preporucujes?
da u pravu su ;)
20000+. Лопата чистит и это главное.
Odličan video...nego gdje si nabavio ovaj ventilator na ručnom breneru?
ma to ti je glupost ziva nist negrije
Good work.
Interesting video, avtor 💪 💪 💪 💪 thank you All power
Very cool way to have fun in your shop and way more fun than shoveling snow lol thanks for another great vid! :)
Creativity is nice. Doesn't seem to work too well though. Possibly adding rear weights 🤷♂️
BRAVO! Felicitari!
Jel ti te projekte radis iz glave ili pravis nacrte mjere i sve
inace svaka cast!
Nice work young man!!
Nice project.
That was a beautiful job that you made that is really awesome
Well on bro
Svaka čast
:D
From Greece. Very good
I give eem credit, he tried making somthing basically out of nothing 👍
Nice job young man.
THAT IS FRIGGINNN COOL....
Funny thing I made 1 of them about 5 years ago. Neighbor I should put a patient on it. But told him troy bilt already made it. Nice job on urs
To care bas dobar klip ida ima jedno pitanje desi nabavio taj lim i koliko si ga platio
Ma uzmi bacvu od ulja i na pola prerezi
lim je 2mm ali davno ga platio mislim oko 40 eura
@@DShomemade Hvala
I liked your innovation
Pozdrav iz Bribira!!!
Poz iz Virovitice
Buen trabajo DS. Saludos desde Santander.
Super master
Svaka čast za ideju ali moras staviti lance da te ne baca lijevo i desno hahaha
daaaa trebaju lanci a i gume su od kartinga pa su malo izlizane hahahha
Ti si kraljina ceg se ti nes dosjetit
:D
Very good 😚
Snowblower is faster and does a cleaner job nice work though
but why do that? this is more fun!
Snowblower is more money though unless you get the craigslist special😂
As a tin knocker there is a better way to do that roll on the metal. FIY in the future most hvac shops would have let you just roll it on one of their machines , but if not make a jig. It’s way easier
Ratchet straps around a barrel?
Dobro si napravio
Treba jos malo zaobliti. U svakom slučaju bravo
😊