Dear Sir, thanks for showing snippets of your lathe build. Excellent job. I liked the way you produced a headstock shaft with a bore, not solid. Do you happen to have plans… a) For further development like motorising drives and b) Actual plans for making another model of your design?
Interesting project but using pillow box bearings could be a problem they are totally inaccurate. Too much slop in that type of bearing should use a pair of angular contact ball bearings 72xx be type works for me!
Hi, purpose of the smaller rail set is for making cone and other stuff under some angle, whole plate with rails rotates around bolt in middle. Also so i can adjust paralelnes of machine. Thank you for watching! 😁
Really a nice job. All the right pieces including some that were not scrap. Very rigid. Two things we almost never see in this kind of DIY project: cost and precision. It would be very interesting to see the money spent on scrap metal and purchase parts, separated. Test precision by placing a ground round bar between centers and run a test indicator down the bar once along the top and again along the side.
Hello, total cost was around 600-700$ Chuck was 150$, rails around 250$, pulley around 25$ each and steel parts at scrapyard 150$ and a lot of screws... Best option for sure is to buy regular lathe😅 but i have realy small workshop and i dont need too high presition for my projects. Also regular cheapest normal sized lathe in my country is anywhere from 3000 to 5000$😅😅 Also thank you for commeting have an nice day!
@@davidwillard7334 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran
И не говоря о том, что в самоделке нихрена не отшлифовано и не отфрезеровано, никакой проверки на биение и параллельность, нет нормальной продольной и малой продольной подачи, нет ходового и винта и валика, нет нормалтной регулировки скоростей, нет лимбов
Where fine big huge piece of scrap like that? All the scrap I can find is just that, SCRAP. Not massive long untouched beams and sheets. Big stuff like that is not able to do anything with because it's part of a machine which hasn't been cut apart. Has to be cut small to be able to be put in some of the equipment at my local scrap yard. Your either very lucky or decieving us and buying the metal
так этот станок без претензии на высокую точность, а значит и шабрить там смысла нет! рез чистый без биений, без дроблений, а что еще надо от самодельного станка...Там пришабривать бесполезно так как от сварки вся рама винтом и горбатая.
They told me that this system is not good as a lathe but only as a cnc. Working with steel it is very easy for everything to break because it has no cutting power and the system is destined to last very little as well as not being safe for safety. I am trying to partially replicate your project but everyone is not recommending it to me. Do you have any work that is a bit more strenuous in order to appreciate that everything works fine? Thank you in advance :)
Sounds like the factors you are discussing are rigidity and dampening. Yes, this type design would have poor dampening. However it lends itself to be epoxy granite filled which will solve that. Secondly is the cross slide. This setup will have limitations on the depth of cut you can take. You will need to be weary of tool pressure. Other ideas to improve rigidity would be square linear rails, 30-35mm would likely do or even better yet box ways but this requires a way to precision grind and/or scrape.
Veoma dobro odradeno! Pohvale mladom gospodinu!
"Very well done! Kudos to the young gentleman!"
Nice, but Maybe finish up all welding? 🤔Seems to be tacked at some places, it could be much more stable when welding it up
Those are some good pieces of "scrap" metal✌️😂🤣💚🇬🇧🌱
Yeah I thought that. They don't look anything like the "scrap metal" I come across.
Excelente trabajo!!! Muchas gracias!!!
Excellent
Dear Sir, thanks for showing snippets of your lathe build. Excellent job. I liked the way you produced a headstock shaft with a bore, not solid.
Do you happen to have plans…
a) For further development like motorising drives and
b) Actual plans for making another model of your design?
Yeah, right - "scrap" metal - shiny rollers and guides from China.
Yeah? What, you want him fabricating linear rails himself?
@user-cg3em4cw4f No, just get quality stuff from Japsn, Korea, or the USA, which actually is built to specification and won't make a mess of his jobs.
@@dnomyarnostaw Ah, I took it as one of those comments complaining that technically the rollers weren't scrap. My bad, definitely true.
Главный параметр любого станка - это ЖЕСТКОСТЬ , а алюминиевые направляющие не могут обеспечить необходимую жесткость ....
AND SUCH A HOME-MADE MACHINE CAN BE MUCH MORE THAN MANY PURCHASED. I KNOW FROM EXPERIENCE
Complimenti spettacolari...ma ti ricordo che il tornio ha anche la contropunta..la farai a suo tempo?
Very good
Good work,you can be proud of your work, looks nice.
Very well thought out, designed and put together. You made it so anyone can make one. I'm curious though, do you ever plan on making plans available?
Svaka čast
Interesting project but using pillow box bearings could be a problem they are totally inaccurate. Too much slop in that type of bearing should use a pair of angular contact ball bearings 72xx be type works for me!
Good point……he does have a Precise lathe for close tolerance work so it doesn’t matter this is just a video not a do the build like this or else!
@@scor440 I can't stop laughing due to your comment 😂👍
Could you provide a link to the bearing you mention? I’d like to see how much more precise it is, and the price difference of course! Thanks!
Great thinking outside the box
Nice job. We shared this video on our homemade tools forum this week 😎
Svaka ti cast!
what is the name of the aluminum elbow for the sliding rail? and where to buy it? You made it very well. thanks.
Excelente diseño, y muy bien heho el montaje, muy ptofesional, 👍👍
Good Work. Much better quality can be achieved using couple of tapper roller bearings in head stock!!
Sempurna ! Saya sangat menyukainya !!!😍
Good 👍
👍👍👍
Good job making it work with what you can afford or salvage! Kudos!
Making it happen!!!! :)
welldone,
im impressed
Как спустя год ведет себя станок, вылезли ли какие нето болячки?
You are awesome!
What is the purpose of the smaller (300mm) rails? Why it is not enough to have longer (lower) rails in left/right direction?
Hi, purpose of the smaller rail set is for making cone and other stuff under some angle, whole plate with rails rotates around bolt in middle. Also so i can adjust paralelnes of machine. Thank you for watching! 😁
Well done 👏 ,it's a commendable skill
Impressive!
bravo majstore,pozz iz Slovenije
Porque você não ensina como marcar os buracos da chapa p rolamento p dar certo
Maybe he did use some new parts but, what he did was really quite impressive.
Boa tarde) vc faz desse torno pra vender? Valor????
Great job
Buy tabriz lath machine
This is the best machine factory in the world
Iranian lath machine are best
Esta super
En poco tiempo va sacar el doble provecho. Saludos
Parabéns ficou show de bola 👏👏👏👏👏
Estes trilhos, onde consigo comprar? Lojas etc.
Why so many dislikes? You done a great job mate
nice work
Is very good
Show de bola ⚽️muito bom 👍👍👍👍👍
Really a nice job. All the right pieces including some that were not scrap. Very rigid. Two things we almost never see in this kind of DIY project: cost and precision. It would be very interesting to see the money spent on scrap metal and purchase parts, separated. Test precision by placing a ground round bar between centers and run a test indicator down the bar once along the top and again along the side.
You always wonder ! What costs More !??
Hello, total cost was around 600-700$ Chuck was 150$, rails around 250$, pulley around 25$ each and steel parts at scrapyard 150$ and a lot of screws... Best option for sure is to buy regular lathe😅 but i have realy small workshop and i dont need too high presition for my projects. Also regular cheapest normal sized lathe in my country is anywhere from 3000 to 5000$😅😅 Also thank you for commeting have an nice day!
@@davidwillard7334 ⚠️ God has said in the Quran:
🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )
🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 )
🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 )
🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 )
🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 )
⚠️ Quran
That's impressive my dude! Love it... I'll have to check it out in person ;)
Sure, naleti kad god hoces! :)
So washing machine motor powers this? So household voltage?
support to you friend
BG,,mantap,,,itu beli rel nya di mana
Very nice
Good
Where did you buy the ways? How do you lock the tool carriage down?
Assalamu alaykum very good
Congratulations!!! That is a very beautifully built machine.
Respect
Ukuruan panjang dan lebar jarak nya berapa ? Mohon di jawab terimakasih
Indeed scrap metal 😂
Bravooo e super strungul
TOP PARABENS
so where did you find scrap rails and screws?
And Welder ! / Rod ! Too ??
Hello! What kind of bearings?
А регулировки были?
Super 👍👍👍👏👏👏🇵🇱
Эти линейные подшипники очень слабые для станка, там пластмассовые детали, никогда не делайте так . Это не будет долго работать
И шпиндельные тоже.
И не говоря о том, что в самоделке нихрена не отшлифовано и не отфрезеровано, никакой проверки на биение и параллельность, нет нормальной продольной и малой продольной подачи, нет ходового и винта и валика, нет нормалтной регулировки скоростей, нет лимбов
Di ti je ona iz lidla parkside stupna
Senapan pcp bikin bg
Where fine big huge piece of scrap like that? All the scrap I can find is just that, SCRAP. Not massive long untouched beams and sheets. Big stuff like that is not able to do anything with because it's part of a machine which hasn't been cut apart. Has to be cut small to be able to be put in some of the equipment at my local scrap yard. Your either very lucky or decieving us and buying the metal
How much sir
Muito bom
Хотя бы болгаркой пришабрил соприкосновение плоскостей профиля и направляющих, а то просто силой притянул их типа и так сойдёт...
так этот станок без претензии на высокую точность, а значит и шабрить там смысла нет! рез чистый без биений, без дроблений, а что еще надо от самодельного станка...Там пришабривать бесполезно так как от сварки вся рама винтом и горбатая.
ovako seksi video se retko vidja, pozdrav iz srbije
Інтересний станок,а розміри його можна.Дякую...
They told me that this system is not good as a lathe but only as a cnc. Working with steel it is very easy for everything to break because it has no cutting power and the system is destined to last very little as well as not being safe for safety. I am trying to partially replicate your project but everyone is not recommending it to me. Do you have any work that is a bit more strenuous in order to appreciate that everything works fine? Thank you in advance :)
Sounds like the factors you are discussing are rigidity and dampening. Yes, this type design would have poor dampening. However it lends itself to be epoxy granite filled which will solve that. Secondly is the cross slide. This setup will have limitations on the depth of cut you can take. You will need to be weary of tool pressure. Other ideas to improve rigidity would be square linear rails, 30-35mm would likely do or even better yet box ways but this requires a way to precision grind and/or scrape.
Convert into...CNC
okay, that SBR rails are scrap metal..
this lathe need tailstock)
that don't look like scrap metal to me..
Great video, disappointing that you say made from scrap but then you stick brand new inline rails on there.
Scrap huh,what is that about $5000 worth of scrap.if I had that kind of scrap I’d just go buy new lathe’s
What's the precision of your lathe?