@ubuntulinux7569 Thank you so much for your kind words! I'm glad you found the video helpful and consider me a true legend. It means a lot to me. I strive to provide informative content and help viewers like you with their Wi-Fi network extension needs. If you have any more questions or need further assistance, feel free to reach out. Thanks again for your support!
Awesome video! The diagram says you can potentially recieve wifi from client 100m then send another 100m, potentially bridging 200m. But im guessing the LBE will need to be pointing at the client router to recieve the signal so it could only send it back in the same direction?
@XPXWORD Thank you so much for your positive feedback on the video "How to Extend Your Wi-Fi Network with UBIQUITI LBE-5AC-GEN2"! We're glad to hear that you found it helpful and informative. If you have any questions or need further assistance, feel free to ask. We appreciate your support! 😊
@thorloki2271 Hello! Thank you for watching our video on extending your Wi-Fi network using the UBIQUITI LBE-5AC-GEN2 in client mode with OpenWrt firmware. Regarding your comment, the configuration demonstrated in the video is not in bridge mode but rather in router mode using OpenWrt firmware. In the demonstrated setup, the UBIQUITI LBE-5AC-GEN2 device is configured as a router rather than a bridge. This means that it will assign its own IP addresses to devices connected to its LAN ports or Wi-Fi network, creating a separate network segment. To clarify, in this setup, your desktop's IP address will be assigned by the UBIQUITI LBE-5AC-GEN2 device itself, not by the main access point (AP) of your Wi-Fi network. The UBIQUITI LBE-5AC-GEN2 acts as a router, providing network services and IP addressing for devices connected to it. If you prefer to have your desktop's IP address assigned by the main AP and be part of the same IP subnet as the main network, you would need to configure the UBIQUITI LBE-5AC-GEN2 in bridge mode. In bridge mode, the device will act as a transparent bridge, forwarding traffic from the main AP without performing routing functions or assigning separate IP addresses. Please note that configuring the UBIQUITI LBE-5AC-GEN2 in bridge mode or changing the network configuration may require different settings and procedures. It's important to consult the device's documentation or seek further guidance from the OpenWrt community or UBIQUITI support to ensure the correct configuration for your specific requirements. We hope this clarifies the setup shown in the video. If you have any further questions or need additional assistance, feel free to ask. Thank you for your comment, and we appreciate your support!
@rog9204 Hi.. Kindly adhere to the instructions provided in the video. Ensure that you carefully follow the steps and guidance outlined in the visual content to effectively comprehend and implement the information conveyed. Your cooperation in following the video will contribute to a smoother and more successful execution of the given task or process.
Broo you are a true legend
@ubuntulinux7569 Thank you so much for your kind words! I'm glad you found the video helpful and consider me a true legend. It means a lot to me. I strive to provide informative content and help viewers like you with their Wi-Fi network extension needs. If you have any more questions or need further assistance, feel free to reach out. Thanks again for your support!
Is it possible to configure it as a universal repeater or WISP?
Can the litebeam 5ac gen2 23 5g only be use as a wifi extender? It doesn't have a 2.4 antenna only 5g
Thanks a lot 🙏🏻 from Marrakech
@maroc7889 You are very welcome...
Darti Australie otla3lik dbm?
Awesome video! The diagram says you can potentially recieve wifi from client 100m then send another 100m, potentially bridging 200m. But im guessing the LBE will need to be pointing at the client router to recieve the signal so it could only send it back in the same direction?
My Litebiam Ac gen2 only has 200mw 23 dbi. this is normal? Is there different hardware?
I have a bullet AC, with OpenWRT can I use it as an Access Point for any device (TV, mobile phones, computers) taking advantage of the larger antenna?
Yes....
Very good video 😊
@XPXWORD Thank you so much for your positive feedback on the video "How to Extend Your Wi-Fi Network with UBIQUITI LBE-5AC-GEN2"! We're glad to hear that you found it helpful and informative. If you have any questions or need further assistance, feel free to ask. We appreciate your support! 😊
@@Istoryahetvvlogs 👍😀
Can i use it as a repeater after installing openwrt?
Can we install open rts in lap 120 sector
Thank you good sir
Thanks 😊
Can litebeam 5ac 23 does this?
I made everything the same till 2:30 but cannot open 192.168.1.1 why that happens any idea?
good day sir, can i ask if this is in bridge mode in where you get your desktop ip from the main ap
.
@thorloki2271 Hello! Thank you for watching our video on extending your Wi-Fi network using the UBIQUITI LBE-5AC-GEN2 in client mode with OpenWrt firmware. Regarding your comment, the configuration demonstrated in the video is not in bridge mode but rather in router mode using OpenWrt firmware.
In the demonstrated setup, the UBIQUITI LBE-5AC-GEN2 device is configured as a router rather than a bridge. This means that it will assign its own IP addresses to devices connected to its LAN ports or Wi-Fi network, creating a separate network segment.
To clarify, in this setup, your desktop's IP address will be assigned by the UBIQUITI LBE-5AC-GEN2 device itself, not by the main access point (AP) of your Wi-Fi network. The UBIQUITI LBE-5AC-GEN2 acts as a router, providing network services and IP addressing for devices connected to it.
If you prefer to have your desktop's IP address assigned by the main AP and be part of the same IP subnet as the main network, you would need to configure the UBIQUITI LBE-5AC-GEN2 in bridge mode. In bridge mode, the device will act as a transparent bridge, forwarding traffic from the main AP without performing routing functions or assigning separate IP addresses.
Please note that configuring the UBIQUITI LBE-5AC-GEN2 in bridge mode or changing the network configuration may require different settings and procedures. It's important to consult the device's documentation or seek further guidance from the OpenWrt community or UBIQUITI support to ensure the correct configuration for your specific requirements.
We hope this clarifies the setup shown in the video. If you have any further questions or need additional assistance, feel free to ask. Thank you for your comment, and we appreciate your support!
@@Istoryahetvvlogs thank you for this information, it clarify most of my concern.
Says failed to confirm apply in 90sec
why configurated reset after power off and on again?
Mine was doing the same. It is because of the highest version of openwrt. When replace it with a lower version, the problem solved
hello sir .. can you please share with us instruction notepad file. and thank you so much sir
firmware please
Firm ware 23.05.0 presume that’s the newest firmware
boss pano i set siya permanent kada restart kasi balik setup nanaman
@rog9204 Hi.. Kindly adhere to the instructions provided in the video. Ensure that you carefully follow the steps and guidance outlined in the visual content to effectively comprehend and implement the information conveyed. Your cooperation in following the video will contribute to a smoother and more successful execution of the given task or process.
Why set to AU country.?
Because he's in Australia, I'm in Italy and I'm setting up IT
same question why AU?..