closest thing to dark mode is right there in "Inactive Backlight". You choose the level of brightness. then there is a nightlight setting too. The T9 has it also. 10% is the minimum brightness.
@@davewelike understood. I will be putting these in my 2 zones. Seems similar similar to my setup. Like that I can do temp in bedroom and not the hallway. Lol. I probably waste a lot of energy trying to cool my halfway
@@craiggrant693 exactly. Makes more sense to do the bedroom temperature than a place you're not in. Especially if you close the door. Blocks air from getting into the hallway. I find the bedroom to be much cooler than the hallway. Plus when I leave the ac turns up automatically. So I've already noticed a reduction in my electricity bill. Compared to last time this year I've saved $20.
Does your thermostat show a higher temperature (+2 to +3 F) compared to the remote? I have six remotes and they have the correct room temperatures. But the thermostat seems to run warmer than the remotes. I placed remotes 12” on either side of the thermostat and use those as the temperature source. Seems to be a common issue with this thermostat!
Have you had problems with the sensors not reporting the temperature change fast enough? For example when I turn the ac on and watch the thermostat temp I can see it change from one degree to another however the sensor nearby doesn’t report it till several minutes later which is so strange and makes me think prioritizing the sensor will lead to extended run times. Even tested it by putting it in the fridge which runs at 37 however it took forever to change ( half an hour an it barely read 51 after starting at 78)
I guess I never tested like that. I had other temperature reading sensors and they all generally were around the same numbers. Maybe the battery power is too low or too far away from the main sensor?
Mine is changing temperature on its own. It started after I set a vacation schedule 2 weeks ago. I have it set to 75° when I wake and 71° at night. However, once it change to 73° in the morning. In another instance I came home and it was 71°, when it should be 75°. I unabled the adaptive feature, replaced the batteries in the remote sensor. If it’s still doing that, I’m thinking just give it a hard reset. How do you do a hard reset? Thanks!
I have our T10 thermostat set to go to a night time schedule at 10:00 p.m. with a temperature setting of 62 degrees. The daytime temperature is set to 68 degrees. If I move the day time temperature to 69 degrees the system should at 10:00 p.m change to the sleep schedule but it often does not and I have to manually set it back to 68 degrees and then it will change to the sleep mode. Also for wake it is set to go on at 7:00 a.m. and heat to 68 degrees but it goes on before with a message that states something like heating to recovery schedule??? What is that and how do I turn it off?
It's a setting in the thermostat, but you have to have an HVAC system with an integrated humidifier or dehumidifier in order for it to actually do something. Just enabling the option doesn't magically make it work.
I just had a new HVAC system installed and they also installed this thermostat. The program setting will not work with the sensor. If we set the program then the unit runs constantly. The technicians answer was to just not use the program setting because most people don't use it anyways. I want to use it. He called Honeywell and was on the phone with them and still could not figure it out. What do you think about this?
question for you or anyone, this is our second cooling season now on this t-stat, and for some reason, it makes the system run forever. like today here in PA, we just turned on the ac, it was i think 77 or 78 in the room the tstat is in, we have it set to come on a certain time at 75, and drop to 77 like later in the evening to sleep, it has ran for over 3 hours to cool to the 75, never got there. i actually watched it go to 75, then right back to 77, and now its at 76, and we pushed it up to 76 to get it to stop running and it didn't stop. any suggestions what is going on? why when it reached the desired temp it doesn't shut off, so frustrating for a new system, and it just runs all the time, my electric bills in almost $400 per month. thanks
@@davewelike they just were out 2 weeks ago to do yearly service for it, and stated everything looked great. humidity is saying 62%, its set to zero on the setting there is a pipe from the new unit hooked up to outside air pvc pipe
closest thing to dark mode is right there in "Inactive Backlight". You choose the level of brightness. then there is a nightlight setting too. The T9 has it also. 10% is the minimum brightness.
How does the T10 compare to the Honeywell Vision Pro 8000?
Great job. Very thorough.
Thanks!
Great job with the detail review. Did you attempt to setup Apple Homekit and see how it works with other smart devices? Thank you for taking the time.
I have Android. 😵💫
@@davewelike understood. I will be putting these in my 2 zones. Seems similar similar to my setup. Like that I can do temp in bedroom and not the hallway. Lol. I probably waste a lot of energy trying to cool my halfway
@@craiggrant693 exactly. Makes more sense to do the bedroom temperature than a place you're not in. Especially if you close the door. Blocks air from getting into the hallway. I find the bedroom to be much cooler than the hallway. Plus when I leave the ac turns up automatically. So I've already noticed a reduction in my electricity bill. Compared to last time this year I've saved $20.
Does the app show if the fan is running
How do you get it to go below 70 degrees?
Can the T10 respond remotely to Humanity changes and allow me control my compressor at a set percent and temperature?
What’s the diff what is your budget?event the 9t9
Is this stat better than the honeywell rth9600
Does your thermostat show a higher temperature (+2 to +3 F) compared to the remote? I have six remotes and they have the correct room temperatures. But the thermostat seems to run warmer than the remotes. I placed remotes 12” on either side of the thermostat and use those as the temperature source. Seems to be a common issue with this thermostat!
I haven't noticed that. My issue is my bedroom gets coldest fast so I set priority to that room so it doesn't get too cold in that room.
Have you had problems with the sensors not reporting the temperature change fast enough? For example when I turn the ac on and watch the thermostat temp I can see it change from one degree to another however the sensor nearby doesn’t report it till several minutes later which is so strange and makes me think prioritizing the sensor will lead to extended run times. Even tested it by putting it in the fridge which runs at 37 however it took forever to change ( half an hour an it barely read 51 after starting at 78)
I guess I never tested like that. I had other temperature reading sensors and they all generally were around the same numbers. Maybe the battery power is too low or too far away from the main sensor?
THM04R3000 vs THM5421R1021
What is the difference between these EIMs?
Mine is changing temperature on its own. It started after I set a vacation schedule 2 weeks ago. I have it set to 75° when I wake and 71° at night. However, once it change to 73° in the morning. In another instance I came home and it was 71°, when it should be 75°. I unabled the adaptive feature, replaced the batteries in the remote sensor. If it’s still doing that, I’m thinking just give it a hard reset. How do you do a hard reset? Thanks!
Delete your account and add the thermostat to your new account. Would that be considered a reset? If not contact support.
Why does it say "Do not connect W wire" on the lid that snaps over the wires????
I have our T10 thermostat set to go to a night time schedule at 10:00 p.m. with a temperature setting of 62 degrees. The daytime temperature is set to 68 degrees. If I move the day time temperature to 69 degrees the system should at 10:00 p.m change to the sleep schedule but it often does not and I have to manually set it back to 68 degrees and then it will change to the sleep mode. Also for wake it is set to go on at 7:00 a.m. and heat to 68 degrees but it goes on before with a message that states something like heating to recovery schedule??? What is that and how do I turn it off?
Don't know what could be going on. Definitely contact their support.
How long does the sensor battery last?
I haven't changed it yet and it still works.
I purchased this thermostat but can't see humidification option in the main menu for some reason
I only have the dehumidity setting upstairs and it's not available downstairs. Must be a wiring thing. Ask Honeywell.
It's a setting in the thermostat, but you have to have an HVAC system with an integrated humidifier or dehumidifier in order for it to actually do something. Just enabling the option doesn't magically make it work.
Where does it show the actual room temp not just the cooling to temp?
Click on the screen and the first temperature listed first is room temperature.
Interesting I never see it change and my AC seems to run more often since the upgrade.
I just had a new HVAC system installed and they also installed this thermostat. The program setting will not work with the sensor. If we set the program then the unit runs constantly. The technicians answer was to just not use the program setting because most people don't use it anyways. I want to use it. He called Honeywell and was on the phone with them and still could not figure it out. What do you think about this?
By setting the program do you mean setting the schedule? I only use home and away settings.
@@davewelike yes setting the schedule.
I wonder if he wired it correctly. Have you tried to call Honeywell to confirm?
Unfortunately with Honeywell thermostats you can only use geofencing or scheduling. Not both at same time.
I can not view my outdoor temp on the home screen. It used to be there and disappeared.
Did you enter your Address in the app?
question for you or anyone, this is our second cooling season now on this t-stat, and for some reason, it makes the system run forever. like today here in PA, we just turned on the ac, it was i think 77 or 78 in the room the tstat is in, we have it set to come on a certain time at 75, and drop to 77 like later in the evening to sleep, it has ran for over 3 hours to cool to the 75, never got there. i actually watched it go to 75, then right back to 77, and now its at 76, and we pushed it up to 76 to get it to stop running and it didn't stop. any suggestions what is going on? why when it reached the desired temp it doesn't shut off, so frustrating for a new system, and it just runs all the time, my electric bills in almost $400 per month. thanks
Have you checked the ac itself to see if it is functioning normally? Also what is your humidity setting set to? Are you intaking air from the outside?
@@davewelike they just were out 2 weeks ago to do yearly service for it, and stated everything looked great. humidity is saying 62%, its set to zero on the setting
there is a pipe from the new unit hooked up to outside air pvc pipe
@@robwinemiller9712 your dehumidify % is set to zero? Set it to a normal range like 50-60%. That's why your ac keeps running.
@@davewelike I was saying my indoor offsets are set to zero, looks like the factory settings on dehumidifier is set to 60%
@@robwinemiller9712 ask Honeywell if your ac guy can't figure it out.