SINGLE-engine | TWIN-engine | MULTI-engine | How to Wire ESC & RECEIVER
ฝัง
- เผยแพร่เมื่อ 16 มิ.ย. 2024
- STL Files: cults3d.com/en/3d-model/gadge...
DC6 Full Build Video: • BUILDING an AMAZING DC...
In this video I am using 30amp ESCs that has a 5v BEC lead to power the receiver. You only need one power lead for your receiver so if you are building a multi engine plane you will need to remove the red power lead from the other ESCs. The brushless motors I am using are 2212 1400kv. The receiver is a AR620 with a NX-10 transmitter.
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmi...
See what else I am working on:
/ troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #itflies
00:00 SINGLE-engine | TWIN-engine | MULTI-engine | How to Wire ESC & RECEIVER
00:14 How to Wire a Single-engine RC airplane ESC, Battery, & Receiver
00:35 What is a BEC for RC airplanes
01:06 How to Wire a Two-engine RC airplane ESC, Battery, & Receiver
02:29 How to Wire a Four-engine RC airplane ESC, Battery, & Receiver
04:49 How to change rotation direction of a brushless motor - วิทยาศาสตร์และเทคโนโลยี
I'm making my first rc plane project from scratch and this video is just what I needed!
Same for me. I was looking for the two motors.
Same for me. I was looking for the 4 motors for my boeing dreamlifter that I am building from scratch!
Same for me, I have experience flying, but not building. I’m making a twin motor plane with a 70 inch wing span. Almost finished with the wing.
This is very good. You made the topic simple and easy to understand. Thank you
Thank you for this video I can now connect up my Hangar 9 B-25 using two batteries with two ESC’s without worry, excellent video!
I've been looking to make a multi-motor/esc project this has an excellent explanation of the process and options. I haven't been able to find any literature that wasn't 20 years old on this subject , or that didn't give erroneous cautions or methods that just didn't make sense. My local hobby shop actually looked at me funny when I mention what and how I'd like to go about my project, you know like dogs do when they aren't sure what's going on. That was my big sign to find information else where. If you ever do turn this into a document I would gladly store it away with all the other articles and books I have on these subjects
So incredibly helpful, thank you!!!
Nice bench set up, might also mention calibrating the escs all together.... (In something like a twin it's important to be getting relevant thrust from each side.)
Good to see you again
This is really helpful. Thanks for sharing!!
Thank you. Very helpfull video.
Very interesting, many thanks.
Great information. Keep up the good work.
excellent video thanks, very helpful and to the point with no bs and real world example :)
Awesome video 👍
Thank you 😄
Nicely done , thank you. If you want to power two motors on one bigger battery, do you mean more volts or more amps ? Both ? Can you plug à 6s battery to 2 escs accepting 2-4 s lipo without burning them ?
Maybe also worth mentioning that the colors on the 3 motor wires are not relevant - in case people have motors/esc with single colored wires.
And maybe also to check the current drawn by multiple motors - make sure the battery can handle it if you use 4/2 motors on a single battery
Thank you for this!
Great video! quick and easy to undersand. Will you make another one with differential throttle in the future?
Thanks, very helpful
I'm going to use multicopter escs now. They are smaller and lighter but don't have a bec. For that application i use a multicopter pdb with integrated bec where i can solder on up to 8 escs depending on your board. Now i only have to solder on a single battery connector and that's it 😉
I prefer leaving the ESC plugs intact and remove the power ("+") contact(s) from the Y harness(es).
Thanks for explanations. Just subbed to your channel..
Good simple description. If multi-motors are connected to separate battery packs, one weak battery pack may result in one ESC going into low voltage cutoff and one motor cutting out. Using a single higher capacity battery pack may have some advantages in smaller models.
Hi, thanks for the video, excellent. I'm busy building my twin electric model. The twin system necessitated (or so I thought) in extending the leads between the battery and the ESC. I'm told this is incorrect and I will be in trouble; the ESC won't work properly, I should installed a capacitor just before each ESC. The leads between the ESC and the motor should have been extended. My leads are ~600mm long. How did you solve this problem on your multiengine planes? Would appreciate a comment.
I was wondering if that's possible, now I know thanks.
Would the main running one for the servos and all, would it go flatter quicker.
Thanks
I really appreciate this video and I tried to recreate the same thing. However I am having trouble only one of the two brushless motors is running. I have 2x40A ESC and 35c/2200mAH battery. Any help would be greatly appreciated
Is it possible to leave the power wire in the other esc? I'm thinking it be OK since it's in parallel, it would also act as a redundant if the other esc were to fail.
hello Troy, Have you seen the new LW-PLA FW-190 Eclipson model? Will there be your build video and test?
Legend
Do you have your settings anywhere for the Flsun v400?
I'm experimenting with a Stock twin prop 550kv set up. 2x 40A esc, 1x 6s lipo and the max Amp draw is 62A. I'm assuming this is over the 2x ESC combined so my ceiling is 80A. However if I'm going to use 2x lipos I'd certainly not use 2x 6s lipos. The power of the 6s is shared with the 2 motors. I feel if I was going to go dual lipo I'd use 2x 4s lipos. (These motors are 4s rated in 4s planes and 6s for 1 motor would surely be into the 90A+). My question is how do I work out the RPM of each motor in my set up? How much voltage do I know each motor is getting on 6s set up? My aim is to change out the motors to 750kv hoping my stock 40A escs are within operating limits. Cheers
If you are using a dedicated receiver battery that is separate from the flight packs do you disconnect all 4 of the power wires from the ESC’s since the rx is being powered by its own battery?
Yes
Yo what is the name of that wire harness
:15 four GAS props really?
I saw all aircraft you build ..im your subscribers from Philippines..im also love doing drone ang aircraft.....i have diy drone but its broke..ang now i want to build aircraft..help mo for needed materials thank ..
I hope you read this massage
...😜👌
I did it differently..I hooked up one big esc and branched each of the wires coming off it into two.
Seems to work okay, but is this going to cause damage in some way?