Electric Cream Separator # 19 Assembling and Operation
ฝัง
- เผยแพร่เมื่อ 17 ก.ย. 2024
- Assembling and Operation of the Electric Cream Separator # 19
This video is copyrighted. The video is property of www.slavicbeauty.net
You are welcome to share it on your site or blog only with link to www.slavicbeauty.net
MUSIC BY: Kevin MacLeod-Brittle Rille
VIDEO BY: Vasilisa Vasileva
(see video description for details)
Available from: www.slavicbeauty.net
Motor Sich for Slavic Beauty
Wash all separator parts (excluding the base with motor) in a soapy warm water and rinse
Assemble the drum. There is no A and B type discs. All discs are the same. Put them in one by one in any order. Put one at a time to make sure each disc sits in place.
Tighten the drum using the key that comes with the unit
You can regulate the cream thickness by turning the small screw in the drum in (for thicker cream) and out for less fat. Please check out this blog posts by Grass Food for more info
grassfood.me/20...
grassfood.me/20...
Fasten the separator for stability. The separator has to be bolted down to a table top. If you do not have a room for it, bolt it to the piece of board and fasten to the table top with claws for separation. Later you can store it while bolted to the board.
Assemble the separator.
Make sure the milk flow is closed before pouring the milk (or water) in the bowl
We recommend to run warm water through the separator first, before the separation. To warm up the gears and to make sure everything is set up properly.
If you start with milk and the unit is not assembled the way it should, you’ll just waste the milk.
(This is just a recommendation and not a requirement. you can start with the milk and skip the water part)
Pour warm water in the milk bowl first. Before that make sure the milk flow opening is closed in the milk bowl
Turn on the unit and wait for it to get to the full speed. Only then slowly open the valve and allow the water to go through.
Have the warm milk ready. Proper temperature for separation is 100F or 37C. I recommend to warm up the milk to about 110F or 43C, because it will get colder when you pour it in and during separation.
After the water is out, without turning off the unit, close the valve and pour the milk into the milk bowl.
Start to slowly open the valve allowing milk to get into the separator. Once you see that the unit starts processing the milk , the valve can be fully open. Regulate the flow depending on the situation
Please watch out troubleshooting vide to see what happens if the milk is poured in the non working unit.
After separation run skimmed milk through the separator to wash all the cream out from the drum.
Turn the unit off and wait for full stop
Disassemble the unit and wash parts in warm soapy water. The clean up process is very fast and simple if done right after the separation
Dry the parts and assemble the drum. It will be ready for the next separation.
Wipe the base clean. Do not wash the base with electric motor!
Store the unit until the next time
Now you have fresh cream and skimmed milk.
Enjoy the cream with coffee, for cooking, make fresh butter
Check out our blog on using the skimmed milk: www.slavicbeaut...
I’ll be happy to answer any questions you may have about the use of the cream separator
Please not that all other electric models we sell operate the same way
For manual models, please watch the videos about assembling and operating manual models
To avoid any problems, watch out troubleshooting video before the separation
Enjoy!
This is the nicest, most informative and most calming demonstration video I've ever seen. You've made all the steps so clear without uttering a single word!
Thank you, Oliver! I am really glad it is useful. I will be happy to answer any question you may have about SlavicBeauty cream separators
Oliver Sevil
Do I need to put the cones in an alternating order. Are they the same?
sorry, just noticed this. You should alternate type A and type B
At the time when I made the video the discs were the same , now the units have type A and type B discs again.
There are dimples and holes on the discs
Type A has dimples close to holes and type B has dimples away from holes
Thank you so much for the information. I'm ready now.
I ran the water first but there's water coming out of the small hole on the side of the motor housing. How can I fix that?
That happens when too much milk is poured in the separator at once. make sure the opening in the milk bowl is closed once you pour the milk in. Once the unit is at full speed, start slowly opening the milk flow. Please watch the video "troubleshooting" on my channel. it addresses the leaking as well
Why it’s leaking? What I did wrong?
And how to figure out what thickness I made for cream, I can’t find start point.
Does it work with store bought whole milk?
Most of store bought milk homogenized, which means it will not separate. If you find a non homogenized milk, it should work
HOW CAN I GET IT IN Bangladesh
We ship worldwide. please buy from our website www.slavicbeauty.net or please email me at info@slavicbeauty.net Thank you
Koliko je para hteo prazan za mlijeko
Kitne Ki he
Which way do you turn the thickness adjust or to make thicker cream?
To make the cream thicker, turn the screw one or two turns clockwise. I usually leave it at the highest setting to extract the most fat. If I need some cream for cooking or coffee, I just add skimmed milk back to the cream (right after separation)
Legal amei
is this machine come with food grade stainless steel bowel and discs,looking to process400lbs of milk for cream in usa,for sale to public....
this is a unit for personal/home use, not a professional unit.
I want to buy..so where I can get it☺️
Thank you very much for your interest in SlavicBeauty cream separator. Please buy on our website www.slavicbeauty.net or please email me at info@slavicbeauty.net.
m.th-cam.com/video/3Ea-rYLn0oA/w-d-xo.html
for machine call 01921380869
How much price for it
Is it available in India
We can ship worldwide. Please email me: info@slavicbeauty.net Will email you all the information on pricing