Thank you Fred! I took out the valve cartridge, and it looked really bad. I took it all apart, cleaned it all up (steel wool, simple green + toothbrush), lightly silicone greased 'er up, and that inner metal tube now knocks back and forth beautifully! That knocking sound when shaking is the sound of $50!!! Excellent! I suspect in a few years I'll have to dismantle and clean again, but I expect this exercise can happen over and over again. New valve? FORGET IT! Do it Fred's way!!!
Thanks for this valuable bit of info! After 15 years of use, my valve had gotten tight to the point it caused the plastic handle to break the last time I turned it on. That cost me $13 for a new handle, but being able to simply disassemble and re-lubricate this valve saved me an additional $40 cartidge replacement. My valve now works like new again! Thank you for taking the time to post this!!!
I watched this video several times over the years and I can't figure out why Moen doesn't make a PosiTemp valve for their 1225 series. I'ld upgrade un a heartbeat. And as everybody said, great video, thank you!
They do, but it's not a new cartridge cause there isn't enough room in a 1225 for a balancing spool. The Moentrol valves like the 3520 use the 1225 with an external Moen 1423 balancing spool in the body.
Exactly the video I was looking for. I had a 5 year old positemp that was getting unreasonably hard to turn. All it needed was some silicon grease on the o-rings, but I couldn't find any videos detailing how to disassemble the cartridge itself. It works like new now thanks to this.
I had a low water pressure problem coming out of the valve so I watched your video. I followed it EXCEPT..I took out the inner cartridge, tossed it, and it worked like a champ! Great pressure again!
Taking out the spool eliminates the pressure balance function and lets the water mix at full pressure at the input ports. Temperature control will be poor. It's better to clean the rust and scale out of the valve and spool so they move freely.
@@chrisseverance4926I bought a whole new cartridge and still don’t have any cold water coming out. Took the valve back out and I have plenty of cold water flow with it out. Pretty annoying junk design
Fred, THANKS for the great instructions! I was able to repair a Posi temp valve after reusing the two rubber gaskets seals swapped from another valve that had another problem. As you had cautioned at 4:30 of the clip, I broke the rim of the white insert's plastic cap. Still it fit back in there. Won't be able to remove the white insert again though. Everything else worked okay. Repaired valve working fine for over a month now. Critical to use same orientation as before and also grease up when re-inserting the cartridge.
@@SWFLHomeInspector So when I removed my old cartridge I noticed that only one side had the black piece while the other was missing. Could this cause a leak inside the wall by chance? Asking cause this one is on the 2nd floor and I noticed a small stain on the first floor ceiling directly under where the shower is at. Just trying to determine if that was the problem for the small leak or maybe my shower floor is just leaking.
Thank you very much! I thought of soaking the whole valve in CLR or vinegar overnight but your method worked! The plastic sleeve was stuck so I used a 17 mm socket under the base of the sleeve and gently tapped the brass stem down so that the steel cylinder would go down into the socket until the cylinder was dislodged from the plastic sleeve. I also added a few drops of oil which helped to lubricate the cylinder and the sleeve. A box cutter knife helps to gently scrape off calcium crust on the steel cylinder.
Very interesting...I actually just replaced my cartridge today $53 from Home Depot, and it works perfectly, but I think I'll take the old one apart and clean it up to keep as a spare next time. I certainly didn't know you could do this, so thanks for sharing..
Thanks bro, I bought the kits to repair them but wasn't sure of the procedure as the instructions were garbage, answered all my Q's, both of my shower valves, cartridges are now good as new and work great, my symptoms for mine were even after the valves were turned off the would not stop seeping water, constantly dripping which it wasn't bad, but all those drips over a year add up to a lot of water
Thanks for positing this. Will save me $ - every 6 mos or so, mine stops functioning - where I only get cold water unless i throttle the handle back and forth like an idiot until the inner part lines up just right. Probably need a water softner or some other solution to the real root cause, but for no, I can live with a 30 min clean/replace solution each 6 mos.
Thanks for this video. In reassembling it, I don't see how the inner metal sleeve should be positioned. Since it has holes, it seems like how it's oriented matters. Yours jiggles when replaced which suggests it could also rotate, mine not so much but wouldn't the orientation of the orifices make a difference to how it works?
Thank you for a great video. I would like to add that with a brass brush, or soft steel wool one should also clean the inside of the housing. I mean the brass part in the wall that the cartridge goes in. That was in worse shape than the cartridge. I'll order a repair kit, with o rings etc for $10 and next time I'll try repairing it.
At the end of the video you replace the two black seals on the sides of the cartridge but your hand is in the way of how you put them on. I assume that the holes in the seals line up with the holes in the cartridge. Is that correct? Thanks for the video
I knew it, I'll try opening the stem inside, I tried but wasn't sure if it was welded so I didn't. Im having trouble with ours. It's giving to warm water that it's uncomfortable to rinse.
I replaced one after water leak. Didn't recall before replacing but with the new one I'm not getting any cold water. Cold is actually warm water and hot is very hot.
You must have put it in with a different orientation than how it came out . I've done that too/ luckily this video talks about that very thing! You can fix it!
i have the exact same issue, the cold is little warm and hot is hot. I’ve tried all the position. The only way it works on hot and cold nicely is installing it reverse so that it shuts off the water counter clockwise
Thanks Fred. It was quite a useful video. I had one of the inner o rings slightly shaved while removing the inner valve mechanism. Is it OK to use this or will this mix the cold hot water inside?
Friday got a Moen replaced After I installed it, the cold water doesn't run, just a trickle & when I put it in the OFF position it doesn't shut off water. The old one has a rubber cover on the bottom, replacement doesn't. Please advise. Thank you for the good video
Sorry can't help you, I would have to see it to analyze, be sure no rubber parts have "rolled over" . You will know when you try and remove the cartridge, it will be difficult to pull out of the housing/manifold. Best of Luck
So I bought a new 1222 and the pressure is a lot weaker. Now I don't have a leak and turning it on and off is a breeze BUT my pressure is now down. How do you fix this? Can I widen any of these holes? This is so annoying as getting the old one out was a bear. And no there was no debris left on the inside I throughly checked. It's the valve. This is utterly annoying
I have a situation where the handle easily turns on cold water fine but shuts off the water entirely at a point where hot water should come on. We have hard well water here in Florida and this issue started after the water not being used for 3 months while the house was left vacant. Is this a valve issue that can be repaired following the instructions here?
I’ve replaced a couple of these Moen 1222 valves because of very low flow on the hot side. What I observed is that even with a new 1222 the flow rate on the hot side remains poor. I’ve been told that this flaw is actually a design feature. There appears to be no aftermarket solution available. The only answer will be to tear into the wall and replace the entire assembly. I am definitely not a fan of Moen products.
One more question: in order to have the hot side on the left and the cold on the left, I had to put the HC tab on the bottom (that's how the old cartridge was positioned). Should the Off position of the control knob be up or down with the cartridge in this position? Thanks again.
I have an issue. One day my shower was fine then the next it was like next to no water pressure. I replaced the posi temp valve with a new one and still have low pressure. Could the brass mixer be clogged? I removed those side rubber seals on the valve and I had water pressure again. I put the rubber valve seals back on and its back to low pressure. The holes are clear, no obstructions.
Try going downstream of the fixture and see if there are other mixing devices connected to that HW line . www.carsondunlop.com/training/resources/the-importance-of-thermostatic-mixing-valves-to-protect-against-scalding-part-one/ Other than that you may need the assistance of a pro plumber for that I am not .
The only problem I see with what you stated is that typically the little plastic white tabs that you hook the tool onto when you’re removing the valve break. I have never had one come out cleanly where those little white tabs on the end of the valve did not get mangled. One thing I don’t understand is you said it was repaired but I really didn’t see you do anything other than put a little steel wool to it. So what was actually repaired? I know the valves are expensive but I honestly can’t tell what you did to repair it as nothing was actually replaced.
First of all, only use genuine Moen parts. They have a lifetime warranty and are free. As for that puller, it is actually designed for pulling the older 1200 or 1225 type cartridges where the nut can push against the valve body without the "ears" of the 1222 cartridge being in the way.
Do you need to turn off water supply before taking out the cartridge? I live in a condo building and turning off water for the whole building isn’t easy
So, I just went thru this process. 1) the valve is a 1222 not a 122. 2) if the valve doesn't work with hot water then trying to extract the original valve without dame is nearly impossible.
This video is not valid for the newer faucets using the 1222 rebuild kits. Since this was made Moen replaced the cartridge materials with all plastic. The rebuild kits don't work for the new style cartridges. You cant get the O-rings to slide in without getting stuck and cutting the O-rings. If you don't believe me go to Amazon and look up the rebuild kit reviews. Half the people give up and buy the whole cartridge. My guess is this only works with older faucets having all metal 1222 kits. Good luck and hope you have exactly the cartridge as shown in the video. Otherwise buy the whole cartridge for $46 dollars at Lowes or Home Depot.
Thanks but I'm going back to Moen 1222HD Commercial Heavy-Duty Brass Shell PosiTemp One-Handle This plastic is junk and needs to be serviced every 6 months. I got 20 years on solid brass. Good video but tell them to buy brass.
BEWARE - The New Moen 1222 cartridges are using a mostly plastic inside, it has the brass stem as metal now that screws to the handle but the rest of the inside is now made of plastic with only the cams being still made of metal. So Metal glued to Plastic Glued to Metal glued to a plastic end. This new re-design is deliberate so that the plastic breaks and snaps when the 1222 cartridge gets a bit older and stiff. Plastic continually off-gases over its life getting more and more brittle with age. This is a deliberate attempt by Moen to force a huge number of expensive ~$60 new cartridge replacement sales. If you have a choice today never buy Moen. If a builder installs nothing but Moen because they got a kickback sweet deal from Moen for creating a huge inventory of houses with very expensive plastic parts ready to break and create a lucrative market for Moen stay away from all those houses and buy some other builder's house.
@@connielingus6969 moen didn’t replace any of my cartridges. Mine I had to replace. And they are all plastic garbage today. I’m going to get rid of all the moen and never go back.
Thanks a lot! Can't find detailed instructions about 1222 valve, except this one. Very helpful.
My Pleasure
Thank you Fred! I took out the valve cartridge, and it looked really bad. I took it all apart, cleaned it all up (steel wool, simple green + toothbrush), lightly silicone greased 'er up, and that inner metal tube now knocks back and forth beautifully! That knocking sound when shaking is the sound of $50!!! Excellent! I suspect in a few years I'll have to dismantle and clean again, but I expect this exercise can happen over and over again. New valve? FORGET IT! Do it Fred's way!!!
Ahhhhhhhh........that was so nice of you to say you made my day, thank you! Glad I could help....happy bathing.
nice
Thank you very much for your time. I'm a plumber and I always replace these. I never considered repairing them before.
Thank you for visiting our You Tube page best of luck and thank you!
Thanks for this valuable bit of info! After 15 years of use, my valve had gotten tight to the point it caused the plastic handle to break the last time I turned it on. That cost me $13 for a new handle, but being able to simply disassemble and re-lubricate this valve saved me an additional $40 cartidge replacement. My valve now works like new again! Thank you for taking the time to post this!!!
Jeff, Glad we helped you out, thanks for posting a comment.
I watched this video several times over the years and I can't figure out why Moen doesn't make a PosiTemp valve for their 1225 series. I'ld upgrade un a heartbeat. And as everybody said, great video, thank you!
They do, but it's not a new cartridge cause there isn't enough room in a 1225 for a balancing spool. The Moentrol valves like the 3520 use the 1225 with an external Moen 1423 balancing spool in the body.
@@chrisseverance4926 Thanks for the explanation. I've seen the 3520, but was hoping for a plug-and-play solution.
Exactly the video I was looking for. I had a 5 year old positemp that was getting unreasonably hard to turn. All it needed was some silicon grease on the o-rings, but I couldn't find any videos detailing how to disassemble the cartridge itself. It works like new now thanks to this.
Awesome glad we helped you out!
I had a low water pressure problem coming out of the valve so I watched your video. I followed it EXCEPT..I took out the inner cartridge, tossed it, and it worked like a champ! Great pressure again!
Glad it helped
Taking out the spool eliminates the pressure balance function and lets the water mix at full pressure at the input ports. Temperature control will be poor. It's better to clean the rust and scale out of the valve and spool so they move freely.
@@chrisseverance4926I bought a whole new cartridge and still don’t have any cold water coming out. Took the valve back out and I have plenty of cold water flow with it out. Pretty annoying junk design
Love it. Such an easy rebuild. Thanks. You saved me and my wallet. Your video first one about repairing cartridge without simply replacing the valve.
Thank you and glad we could help out Have a great new year
Straight to the point no filler!!! Great instructional video!!!
Thank you glad we could help!
And no stupid background "music" too.
Fred, THANKS for the great instructions! I was able to repair a Posi temp valve after reusing the two rubber gaskets seals swapped from another valve that had another problem. As you had cautioned at 4:30 of the clip, I broke the rim of the white insert's plastic cap. Still it fit back in there. Won't be able to remove the white insert again though. Everything else worked okay. Repaired valve working fine for over a month now. Critical to use same orientation as before and also grease up when re-inserting the cartridge.
Your Welcome .....glad everything worked out for you -stay safe!
@@SWFLHomeInspector So when I removed my old cartridge I noticed that only one side had the black piece while the other was missing.
Could this cause a leak inside the wall by chance?
Asking cause this one is on the 2nd floor and I noticed a small stain on the first floor ceiling directly under where the shower is at.
Just trying to determine if that was the problem for the small leak or maybe my shower floor is just leaking.
@@user-gh8ke1sv2f Yes
Fred, you made a beautiful educational video of how to refurbish cartridge. What causes cartridge from not shutting water off. John
Thank You ! Causes could be but not limited to, sand, grit, corrosion, scale etc. Best of luck !
Thank you very much!
I thought of soaking the whole valve in CLR or vinegar overnight but your method worked!
The plastic sleeve was stuck so I used a 17 mm socket under the base of the sleeve and gently tapped the brass stem down so that the steel cylinder would go down into the socket until the cylinder was dislodged from the plastic sleeve. I also added a few drops of oil which helped to lubricate the cylinder and the sleeve.
A box cutter knife helps to gently scrape off calcium crust on the steel cylinder.
Your welcome glad we could help
Very well detailed video.. I still have to do it all, but now I can try it with more confidence… Thank you
good luck and thank you !
Very interesting...I actually just replaced my cartridge today $53 from Home Depot, and it works perfectly, but I think I'll take the old one apart and clean it up to keep as a spare next time. I certainly didn't know you could do this, so thanks for sharing..
Nice, I just bought a new cartridge and still have the same problem, no cold. Cold flows good when it’s out so it’s not a plugged line
This is awesome thank you. Interesting to see how constructed. Moen does have a lifetime warranty too so if you call them they may exchange the part.
No need to call just go to hardware store and tell them you need a free moen cartridge
You saved my sanity with this, thank you
Awesome thanks for visiting the page.
Finally!! This is I've been looking for! Thank you for making this video!
My pleasure, glad we could help !
Thanks bro, I bought the kits to repair them but wasn't sure of the procedure as the instructions were garbage, answered all my Q's, both of my shower valves, cartridges are now good as new and work great, my symptoms for mine were even after the valves were turned off the would not stop seeping water, constantly dripping which it wasn't bad, but all those drips over a year add up to a lot of water
Glad we could help your welcome !
You should teach plumbing!!! This was a big help!! THX
Ahhh ......thanks but I'll pass on teaching plumbing. I know a little about everything for my job but I am far from a being a licensed plumber.
$40 later from Lowe's I come across this video..smh..lol..but I still have my old one and it'll make good practice disassembling it. Excellent video.
Thank you for visiting our You Tube page best of luck and thank you!
Very clear and useful video! Thanks!
Your very welcome amd thanks for taking time to respond!
@@SWFLHomeInspectorbut I’m sad to find they changed the valve inside from metal to plastic! No way to repair now.
Great! Thanks for the tips. Cleaned up the valve and its works again.
Your welcome, be safe !
Thanks for positing this. Will save me $ - every 6 mos or so, mine stops functioning - where I only get cold water unless i throttle the handle back and forth like an idiot until the inner part lines up just right. Probably need a water softner or some other solution to the real root cause, but for no, I can live with a 30 min clean/replace solution each 6 mos.
Glad we can help--Yes a water conditioning system is good , Happy Holidays
Excellent video. Thank you.
I see they sell rubber parts kit for the 1222B, but I could't find any video showing how to take the valve apart. except for this one!
Glad we could be of assistance !
Many many thanks for this very useful video.
my pleasure TY
Thanks for this video. In reassembling it, I don't see how the inner metal sleeve should be positioned. Since it has holes, it seems like how it's oriented matters. Yours jiggles when replaced which suggests it could also rotate, mine not so much but wouldn't the orientation of the orifices make a difference to how it works?
Thank you for a great video. I would like to add that with a brass brush, or soft steel wool one should also clean the inside of the housing. I mean the brass part in the wall that the cartridge goes in. That was in worse shape than the cartridge. I'll order a repair kit, with o rings etc for $10 and next time I'll try repairing it.
Your welcome glad to be of help and great tip on the interior !
Awesome video! You have helped me save some $$. Thank you
Glad we could help you !
At the end of the video you replace the two black seals on the sides of the cartridge but your hand is in the way of how you put them on. I assume that the holes in the seals line up with the holes in the cartridge. Is that correct? Thanks for the video
Yes--your welcome and have a happy holiday !
Thanks for the video!
Saved me a trip!
My pleasure thanks for visiting !
I looking for this VIDEO!!
Thank you sooooo much!!!
Glad we could help, you're very welcome !
thank you so much for the information. much appreciated.
Your welcome thanks for visiting our page.
I knew it, I'll try opening the stem inside, I tried but wasn't sure if it was welded so I didn't. Im having trouble with ours. It's giving to warm water that it's uncomfortable to rinse.
I just replaced one of these and only lubed the long rubber ovals. Should I take it apart and lube the inside of the rubber oval's also?
I replaced one after water leak. Didn't recall before replacing but with the new one I'm not getting any cold water. Cold is actually warm water and hot is very hot.
You must have put it in with a different orientation than how it came out . I've done that too/ luckily this video talks about that very thing! You can fix it!
i have the exact same issue, the cold is little warm and hot is hot. I’ve tried all the position. The only way it works on hot and cold nicely is installing it reverse so that it shuts off the water counter clockwise
Thanks Fred. It was quite a useful video. I had one of the inner o rings slightly shaved while removing the inner valve mechanism. Is it OK to use this or will this mix the cold hot water inside?
I would not use any damaged or altered O-rings.
Friday got a Moen replaced After I installed it, the cold water doesn't run, just a trickle & when I put it in the OFF position it doesn't shut off water. The old one has a rubber cover on the bottom, replacement doesn't. Please advise. Thank you for the good video
Sorry can't help you, I would have to see it to analyze, be sure no rubber parts have "rolled over" . You will know when you try and remove the cartridge, it will be difficult to pull out of the housing/manifold. Best of Luck
Replace with new cartridge but now i have no cold water, any ideas? Tested cold water with no cartridge already.
Good instructions and video work, thanks
Thank You
your most welcome
Thank you for sharing!
Your Welcome !
Great! Thank you!😀😀
Your most welcome
GREAT VIDEO
Thank You, Merry Christmas !
So I bought a new 1222 and the pressure is a lot weaker. Now I don't have a leak and turning it on and off is a breeze BUT my pressure is now down. How do you fix this? Can I widen any of these holes? This is so annoying as getting the old one out was a bear. And no there was no debris left on the inside I throughly checked. It's the valve. This is utterly annoying
I have a situation where the handle easily turns on cold water fine but shuts off the water entirely at a point where hot water should come on. We have hard well water here in Florida and this issue started after the water not being used for 3 months while the house was left vacant. Is this a valve issue that can be repaired following the instructions here?
1222 not 122?
Oh wow, so so sorry 1222, my bad (-;
Thank you
Your Welcome
Your welcome
Great video ! Thanks.
Thank you for visiting our You Tube page best of luck and thank you!
Thank you! I have to say I hate this valve. Pita to get out out even with a puller
Your welcome glad we could be of assistance
Thank you! Very helpful.
My pleasure, glad I could be of assistance.
What about the notch placement?
I’ve replaced a couple of these Moen 1222 valves because of very low flow on the hot side. What I observed is that even with a new 1222 the flow rate on the hot side remains poor. I’ve been told that this flaw is actually a design feature. There appears to be no aftermarket solution available. The only answer will be to tear into the wall and replace the entire assembly. I am definitely not a fan of Moen products.
Good to know, thanks for posting
Oh really? I'm here because of this issue- cold water flows great but when I turn to the hot side its basically just dripping out.
Repair starts at 2:33. You'll thank me later.
Thanks, I found your comment after exactly 2:34 min😃
@@jsollien127 HA!!
One more question: in order to have the hot side on the left and the cold on the left, I had to put the HC tab on the bottom (that's how the old cartridge was positioned). Should the Off position of the control knob be up or down with the cartridge in this position? Thanks again.
I have a lever and the lever is down
The hot side and cold side can not both be on the left...)?
I have an issue. One day my shower was fine then the next it was like next to no water pressure. I replaced the posi temp valve with a new one and still have low pressure. Could the brass mixer be clogged? I removed those side rubber seals on the valve and I had water pressure again. I put the rubber valve seals back on and its back to low pressure. The holes are clear, no obstructions.
Try going downstream of the fixture and see if there are other mixing devices connected to that HW line . www.carsondunlop.com/training/resources/the-importance-of-thermostatic-mixing-valves-to-protect-against-scalding-part-one/
Other than that you may need the assistance of a pro plumber for that I am not .
Is the cam also called a “pressure-balancing spool” or is that something else?
I would " assume" you could call it that
AWESOME. THANK YOU1
My Pleasure thanks for visiting
Would I have to shut off the main water supply in order to remove the valve without water going everywhere?
Yea turn the water off to the dwelling
No, that is what mops are for.
@@jimrussell5016 mops and 15 gal wet/dry vac's + new drywall.
This company must hate your video.
I would not think so because you would still need to purchase genuine Moen parts!
The only problem I see with what you stated is that typically the little plastic white tabs that you hook the tool onto when you’re removing the valve break. I have never had one come out cleanly where those little white tabs on the end of the valve did not get mangled. One thing I don’t understand is you said it was repaired but I really didn’t see you do anything other than put a little steel wool to it. So what was actually repaired? I know the valves are expensive but I honestly can’t tell what you did to repair it as nothing was actually replaced.
My plastic casing seems to be a bit different and I'm having trouble removing it, any advice? Thank you
without actually seeing it I can't help you be sure you are working with a posi-temp valve
I Love this video! Ty, Ty
Glad we could help---Your welcome, welcome !
Cómo se llamará el kit de empaques de ese cartucho 1222
Thank you
First of all, only use genuine Moen parts. They have a lifetime warranty and are free. As for that puller, it is actually designed for pulling the older 1200 or 1225 type cartridges where the nut can push against the valve body without the "ears" of the 1222 cartridge being in the way.
Thank you for visiting our You Tube page best of luck and thank you!
Dynamite, thank you.
Your welcome glad we could be of assistance
Do you need to turn off water supply before taking out the cartridge? I live in a condo building and turning off water for the whole building isn’t easy
There should be a valve on both sides to turn off the water just a quarter turn
Yes turn off main water supply
nice!
TY
❤
Damn! I'll just buy a new one. Good to know in case of zombie apocalypse.
Or call moen and get it replaced for free. These are under warranty. They are suppose to be guarunteed for life.
@@barbarazylema3584 Moen requires a copy of the original purchase receipt.
So, I just went thru this process. 1) the valve is a 1222 not a 122. 2) if the valve doesn't work with hot water then trying to extract the original valve without dame is nearly impossible.
Thank you for visiting our You Tube page best of luck and thank you!
The people that disliked this video are shady plumbers and Lowe’s
Thank you for watching our video, hope this helped you out with any issues.
Twelve twenty two. Not one twenty two. Hope this helps.
Moen has lifetime warranty on product parts. Call them for replacement, for free!
Thank you for visiting our You Tube page best of luck.
This video is not valid for the newer faucets using the 1222 rebuild kits. Since this was made Moen replaced the cartridge materials with all plastic. The rebuild kits don't work for the new style cartridges. You cant get the O-rings to slide in without getting stuck and cutting the O-rings. If you don't believe me go to Amazon and look up the rebuild kit reviews. Half the people give up and buy the whole cartridge. My guess is this only works with older faucets having all metal 1222 kits. Good luck and hope you have exactly the cartridge as shown in the video. Otherwise buy the whole cartridge for $46 dollars at Lowes or Home Depot.
Thanks for the update---the original post was 12/19/13---hopefully all reading will catch your post !
Thanks but I'm going back to Moen 1222HD Commercial Heavy-Duty Brass Shell PosiTemp One-Handle
This plastic is junk and needs to be serviced every 6 months. I got 20 years on solid brass. Good video but tell them to buy brass.
Thank you for visiting our You Tube site
DO NOT JUST SHOVE BACK ON! you will shear off the inner O rings. lube and gentle wiggle while slowly pushing the stem assembly back in
BEWARE - The New Moen 1222 cartridges are using a mostly plastic inside, it has the brass stem as metal now that screws to the handle but the rest of the inside is now made of plastic with only the cams being still made of metal. So Metal glued to Plastic Glued to Metal glued to a plastic end. This new re-design is deliberate so that the plastic breaks and snaps when the 1222 cartridge gets a bit older and stiff. Plastic continually off-gases over its life getting more and more brittle with age. This is a deliberate attempt by Moen to force a huge number of expensive ~$60 new cartridge replacement sales. If you have a choice today never buy Moen. If a builder installs nothing but Moen because they got a kickback sweet deal from Moen for creating a huge inventory of houses with very expensive plastic parts ready to break and create a lucrative market for Moen stay away from all those houses and buy some other builder's house.
Who is paying you to trash Moen? Moen cartridges are guaranteed for life.
@@connielingus6969 moen didn’t replace any of my cartridges. Mine I had to replace. And they are all plastic garbage today. I’m going to get rid of all the moen and never go back.
Remember folks if there’s a video on how to fix a shower valve, that means the brand is trash, Moen.
A poorly designed cartridge by Moen...
no need to buy... moen is for life... just go to Home Depot and pick up a new free one.
Not true. That's why they sell rebuild kits. No warranty for cartridge.
you have to contact moen directly for a free replacement
@@arcin69 home depot opens a drawer and says here you go. free
Thank you sir
Edit your video please. It’s not 122, it’s 1222.