How to Check Your Ride Height (Shock Therapy LIVE 4/20/21)
ฝัง
- เผยแพร่เมื่อ 26 ส.ค. 2024
- More details on when and why to check and set your ride height:
shocktherapyst....
Thank you for watching our video! Shock Therapy is a world-class suspension tuning and component company based in Phoenix, Arizona. We make original products right here in the USA and ship worldwide to all customers. Whether you are a casual owner or a racing enthusiast, Shock Therapy makes sure to place you FIRST. Purchase our sway bars, toe links, shocks, ride improvement systems, and more at www.shocktherapyusa.com
For more information on Shock Therapy, keep up with us on our other Social Media:
FACEBOOK | shocktherapyllc
Mitch says "2 inches is a big deal" I've been trying to tell the Ladies that for years.
Kentucky,Tennessee There's Rockbouncers,and they run Side-by-sides in full blown compitions FYI
Good stuff guys!! Definitely a critical adjustment!
I run mine a little higher for rock crawling and deep rutted trails I ride! I have your dual rate spring kit for my XX! Works great at 15.5” rear 16” front!
I have always wondered why you don't just give a measurement of exposed shock shaft to measure rather than having to measure the tires and such to get a ride height?
That would be a better way but you can’t measure it properly with the coil spring, divider and sometimes a raised spring perch. We had more issues with customers and bent tape measures that way.
When measuring the front X3 I am confused by adding or subtracting an inch. Vid states that the location is an inch lower than the optimal measuring point but he states to subtract an inch from measurement to determine ride height. Wouldn't you need to add an inch to determine ride height? If the tape says 13.5" then my current ride height would be 14.5" and I adjust preload based on that?
Hey dude! this is an updated video of where we measure ride height on x3's. check it out when you have some time!
th-cam.com/video/R2Oq1avEFVA/w-d-xo.html
What about measuring on a Yxz?
Let say I need to adjust my ride height 2 inches. How many inches do I need to adjust at the spring to get that 2 inches?
So does this pertain to stock shock systems aswell? I just put 32s on it and haven't done anything with shocks or was even aware of it.
Yes. This pertains to any shock and spring package.
I have an 2021 X3 max DS TURB R, I have been struggling to fig out the correct ride height. It's pretty low. I have been watching most of your videos trying to educate myself. I guess I need to see how to fig out ways and adjustments in person. I'm a hands on visual learner!
Watch one of our spring kit instal videos for your UTV. It will help you a lot
@@ShockTherapyllc will do for sure. 👍🏼
So a xp w/ 32” tires. 15 F
14 1/2 R it has a 3” lift and high clearance A rams. So I should be looking at 16 1/2 F And 16 R Is that correct
I have the same lift and wondered the same thing. I just adjusted my ride height and I'm at 17 1/4" in the front now. It was 18". I might bring it down a little more even yet.
Also, my rear shocks are at 16 3/4" now.
What shut be the ride high on Yamaha yxz 2017 with 30" tires???
How about lowering the ride height for better cornering and more plush / comfortable ride? I have a rzr 1000 s with fox podium 2.0 and think they are way to stiff even at softest click. I had same car with walker evans and they were a dream very plush and confortable, everytime i needed it i just adjusted the stiffness with the clicks.
Ride height is tricky. Lower it and rail corners. Yes. But depending on the shocks you can run the piston in the wrong zone internally. Lowering can make it stiff. Raising can make it soft. Opposite from common sense I know. Most of the plush or stiffness is inside the shock combined with a ride height choice. Not a simple thing. Great question.
Hey guys i just watched your tool video. Check out a rastal miners wrench for your hammer/adjustable wrench
When increasing ride height does it give it negative camber ?
Yes but not much and depends on the UTV if you could even measure the change or not
I have a 2020 General 2 non XP, factory said it was supposed to be 12 front and back. Never could get there almost maxing out the shock adjustment with No one in the car. I am ordering your shocks, but have already added 4" bracket lift, arched A-arms and went with 15" rims with 32" TR tires.....that's too much math to figure out.
Remove the bracket lift and go with our notes. Just add your tire height change. Should be about 15”
At 20:44 in the timeline are you measuring that round shape on the frame from ground to top, center or bottom of it?
Bottom of it.
Is the turbo s different than what you went over today because those are not what I was told when I got my RIS. Was told 16f -15.5r car on, in soft mode with passenger weight in car
16-15.5 is correct for a Turbo S. 👍
With regards to a 2021 can-am XDS x3 max...with those base height numbers....is that in a safe zone to keep axle CV boot temps in a happy place? Also on the front measurement location, you said to subtract an inch but since its lower then the real location??? Is it not more accurate to say it is 1 inch higher which is why you subtract an inch?
At our ride height numbers your CVS will be fine. We race them there. Fir a more accurate location description check out our spring kit installation video fir your XDS. Max. Or any X3 install vid. FF to the end and check your locations in detail 👍
I have a 2021 xp turbo with 30" tires with stock spring so is it going to be the same height ?
Because i ear the spring work a lot on tight bump and rocks is it because the spring are too tight ?
can you collapse spring too much when trying to achieve ride height
Stock springs yes. Our spring kits no.
How important is your axle angle, what is to much after adjustment and settling?
It’s only an issue if it’s too much all the time. This only happens if your ride height is too high. If you follow our guidelines you won’t have an issue. But let’s assume you didn’t. If you ran your UTV 2” or more above our recommended heights then the cvs would run hotter. If you run your car harder than most the that heat will continue until the boots expand like a balloon and melt causing cv failure. If your UTV is too high but you drive slow (mud) it’s not an issue. If your height is correct abd you drive hard or race it’s not an issue.
Why wouldnt we measure control arm angle instead of ride height since there are so many variables such as tire squish surface and other things that could affect ride height?
Your right. But aftermarket control arms make this hard. Also one degree of are agile can be a lot of ride height. Not a good measuring way fir the average customer. Shock length is best but also hard to get right with a tape measure
I would be curious what the shock length measurements are 64”x3
Mitch if you are only measuring RH from one side(LH) do yo set both shocks to the same measurement?
L to R are always the same. Front to back are different.
What if you’re adjusting ride height on stock suspension on an older car ? should I do that with everyone in the car
You should do that with an average of people weight you run
I have a 2019 CanAm Maverick Sport XRC, that has the Shock Therapy duel-rate springs that was purchased and adjusted by one of your dealers. Can you tell me what the ride height should be, as well as the cross-over adjustment?
13.5” front. 13” rear. XOvers are 1” gap between bottom of XO and top of spring divider. Rear is 2”. Look up outer install vid on your spring kit fir all the details too 👍
@@ShockTherapyllc Thanks for the reply.
Measure crossovers with driver and passengers in car?
👍 yes
Are the ride height measurements the same for a 64" X3 xmr?
All 64 are the same👍
Mitch, should you have a full tank of fuel or is the 60lbs a no big deal? Also when I order a dual spring kit and fill out the questionaire are the springs you provide stiffer with the more weight?
The 60 lbs should not affect it much. Let’s just go with half tank👍 we definitely change spring rates for added weigh on your car
@@ShockTherapyllc If I want a more soft ride would I eliminate the weight figures to some extent, and how would I know how much to take out lb. wise? Just in numbers but not really removing Wt.
@@dickyhead just tell us what ride quality you want. Don’t remove weight figures. Also there is more soft ride potential inside the shocks than in the spring kit. You may need to consider shock internals for a real plush ride
@@ShockTherapyllc Thank you for your help, I fully understand, S. T. ROCKS.(Mitch, Steve, Matt & occasionally Justin.)
Lets build parts for the RS1.....call me! :)
Well, I'm not going to watch if my man crush Justin isn't there!
Pro Xp video is too vague on where to measure off of. You should update video with more time spent on exactly where you're supposed to measure from...
Which specific measurements are you referring to? That way we can give you a more detailed answer.
@@ShockTherapyllc both front and back ride heights. Camera doesn't get close to either, and the description is vague and quick. In the front it says bottom of rear a arm mount, but that could be interpreted a few different ways and if 1/2" of ride height makes a big difference it should be specific. Same with the back, specifically where do you measure to??? Bottom of radius rod mount or actual bottom of skid plate. Both will give different readings. This is where written directions with detailed pictures would be much more helpful than a TH-cam video
@shock therapy llc I'm interested in knowing this also, just had my local dealer install springs and feels a little harsh and to tall of a ride height
@@charliemcdaniel3561 mine is too harsh over small bumps 6" or less. I have appointment with dealer to help fine tune the adjustments but the lack of clear written directions is frustrating. Especially when I'm told ride etc is so important
@@1993kramer small chatter bumps rattle me to death, whoops, jumps, and larger bumps are like a cloud, I'm am definately curious what they tell you to remody the harshness on smaller bumps, mine is the live valve also.