The lube points are on the main step rod on either side of the support brackets as shown in the video. Both sides of the rivets that hold the step panels on each side should also be lubricated as well as the step link from the motor and the step pin connection to the link. By far the most critical area to lubricate is each side of the plates or brackets that support the rod that traverses the complete length of the step from side to side.
That will work in the short term however for longevity apply KwikLube since in addition to a high quality lubricant it leaves a grease follower that keeps water from entering the rod bearing area. This lubricant is the same used in the aircraft industry to lubricate the wing flaps. They are often deployed while going through clouds and the moisture causes all sorts of problems. By using the right lube and you should never have any issues with the mechanical operating part of the step.
The motor is a 12V DC motor. It is a Ford Power Window Motor on newer steps and older early 90's are Chevy. Motors don't fail that often, check the power to it in the multi pin plug and especially the green ground lug for corrosion where it attaches to the frame. Tap it with a hammer while opening the door since occasionally the brushes stick on the armature as it wears. Ensure the step mechanism is free to move since the controller stops power when there is high moving resistance. To confirm, remove the cotter pin from the link and pull out the pin. Then check that the step goes in and out without resistance
THe lubricant is KWIKLUBE now produced by Lippert Components and distributed to RV dealers. It is shown on our website (www.RV-PartsPlus.com) under the products Tab, then Maintenance Lubricants. It is shown in the Yellow labelled tin on the far left of the photo on that page. Here is the direct link: www.rv-partsplus.com/sprays-lubricants-0
The product to use is Kwikee KwikLube which is now a product of Lippert Components Inc. (LCI). It is shown on our website under Product, Maintenance Lubricants, at this link: www.rv-partsplus.com/sprays-lubricants-0
The lube points are on the main step rod on either side of the support brackets as shown in the video. Both sides of the rivets that hold the step panels on each side should also be lubricated as well as the step link from the motor and the step pin connection to the link. By far the most critical area to lubricate is each side of the plates or brackets that support the rod that traverses the complete length of the step from side to side.
Best vid yet....good info...a lot you don't see on other vids that all seem to cover teh same things except....the lub points this guy talks about.
Bravo Zulu, dude, an overnight application of deep penetration oil, onto the the bar you mentioned, fixed the problem. Thank you for posting.
That will work in the short term however for longevity apply KwikLube since in addition to a high quality lubricant it leaves a grease follower that keeps water from entering the rod bearing area. This lubricant is the same used in the aircraft industry to lubricate the wing flaps. They are often deployed while going through clouds and the moisture causes all sorts of problems. By using the right lube and you should never have any issues with the mechanical operating part of the step.
Thank you! This is the best video out there on how to lube and maintain our steps. Much appreciated.
Awesome! I'm heading home to lube and clean them right now! Seriously, great job.
The motor is a 12V DC motor. It is a Ford Power Window Motor on newer steps and older early 90's are Chevy. Motors don't fail that often, check the power to it in the multi pin plug and especially the green ground lug for corrosion where it attaches to the frame. Tap it with a hammer while opening the door since occasionally the brushes stick on the armature as it wears. Ensure the step mechanism is free to move since the controller stops power when there is high moving resistance. To confirm, remove the cotter pin from the link and pull out the pin. Then check that the step goes in and out without resistance
Great video. I'm now ready to troubleshoot my neighbor's motorhome (being careful NOT to be under the non-working steps)!
Great, Feel free to call 877-266-5398 if you still have some issues with it.
Thanks! Helped a ton.
Nicely DONE! Thanks Rob
Great Video! It was quite helpful...
THe lubricant is KWIKLUBE now produced by Lippert Components and distributed to RV dealers. It is shown on our website (www.RV-PartsPlus.com) under the products Tab, then Maintenance Lubricants. It is shown in the Yellow labelled tin on the far left of the photo on that page. Here is the direct link: www.rv-partsplus.com/sprays-lubricants-0
What is the name of the lubrication you use, after cleaning with WD-40? Ty
I missed the quick lube note can you show the product by a picture or specific name ? thx
The product to use is Kwikee KwikLube which is now a product of Lippert Components Inc. (LCI). It is shown on our website under Product, Maintenance Lubricants, at this link: www.rv-partsplus.com/sprays-lubricants-0