WE BUILT A CAR CRUSHER!
ฝัง
- เผยแพร่เมื่อ 18 มี.ค. 2022
- Finally finished the car crusher! It took longer than I thought to complete, but I think it was worth it. Let me know what you think!
🔔 Subscribe for more / hardcorefab
Visit our website: www.hardcorefab.com
Visit our TeeSpring Store: hardcore-fab.creator-spring.com/
Thanks for watching!
#carcrusher #cowboycarcrushing #cowboy_car_crushing #hardcorefab #homemade #hulksmash
#hulksmasher - ยานยนต์และพาหนะ
![ทัศนศึกษาโรงงานผลิตโค้ก [THAI/ENG SUB]](http://i.ytimg.com/vi/M9y-TJBNem0/mqdefault.jpg)
![[TH] VCT Pacific Stage 2 - Week 1 Day 1 // DRX vs ZETA | BLD vs TS](http://i.ytimg.com/vi/AWaOqaxN6Y0/mqdefault.jpg)
If you haven't watched it yet, the best smash is at 10:00. At least that's my favorite!
Cheers mate. That saved 10 wasted minutes👍
He smash the car in the camera!!! 🤣
@@imallowedmyopinionok2354 0
What a rescue mission for that camera lmao
Put 2 smashed cars on top of each other and smash them again please
In the early 80's my friend and I used to visit a scrapyard west of Montreal that had a similar crusher. What differed regarding efficiency between theirs and yours is the following: the pivoting point was only a few inches from the ground. As well an important factor of physics is sheer mass: the swivel structure was filled with concrete increasing the weight of dropping mass, thus the cars in a single drop would have been 12 inches high.
We got one here almost identical to yours that was built almost 35 years ago, quit using it because it took too long to cycle, had issues with the cable and winch , but most of all was unsafe due to no control after it was tripped. Also doesn't work well on vans or SUV's because it blows them out too wide. Hydraulic is really the only way to go. And eventually your hinges will fail and when it does it's not pretty.
Where can i put my ex?
Facts
Great job on the car crusher dude I want to see what it does if you stack one on top of another then drop it I wonder how far it will crush it
Me too, I was going to post the same comment. Can't wait to see this happen!
I wonder what would happen if they turn the car around so that it smashes more of the motor side of the car
EXACTLY
can you submit this to the nearest city as an option for execution? of course only for the atrocious people who deserve it.
@@EternalResonance which ones are that you know occasionally humans do make mistakes and convict the wrong person
Cool build and looks like it works pretty good. You always impress with what you build.
That’s awesome!!
Very cool build for sure. Looking forward to seeing how it all holds up.
Wow that works really well. Good job!
That's pretty bad ass! You can crush as much of those ford's as you want! Lol
Yeah not much lost there. Lol
That thing is brutal. I love it. But I almost cried when you crusher the Intrepid.
First video I've watched on this channel. Can't wait to watch more👍
That was excellent! Nice job 👍
The crusher is cool but that dodge boom truck is amazing. I can’t believe what some people will scrap I would love to own that thing
Love it. You should pour concrete in the top 6ft of it. Reduce the bounce add a few ton.
I think the winch is already pumping it’s little guts out already with the load it’s lifting already.
30k winch whole lid is less then 13K and only picking up one end. The winch is fine!
maybe sand ? concrete might crack if you dont reinforce it
that is really really cool mate, great work
Awesome build!
Hey Tony
Another successful build !
I would like to see a car put in with the engine facing away from the pivot as well as two cars at the same time.
Put a car in upside down.
Stand a car on end.
Put one on it's side.
I mean, sense we are playing, lets try it all !
Thanx fur the entertainment.
Now about the upcoming build with the Super Singles ?
Play Safe, Be Well
Hmmmm that does sound like a good time!
@@HardCoreFab might as well throw some semi’s in there to.
After crushing stak 2 or 3 and see how flat that gets
Make sure that if they still have running engines, you red line 'em during the crushing process. But WAIT! Let me go make some popcorn.
I would look to some sort of cable release and wieght the hook so you can free spool it down because the rapid unspooling seems like that will be hard on the winch. Cool build
When the dog on the winch is disengaged the gears in the winch aren't turning so there is no stress on the winch.
I'm thinking he means like the bushings in the drum etc spinning pretty fast. Probably hurt it over time.
A quick disconnect on the hook end of the cable might prevent that. Sort of like a large car door latch you could pull with a rope on the cable hook end.
@@scubasteve7946 yes plus cable whipping at end
Congrats Tony on building the Hulksmasher to show us how it smashes cars. agree that the cars need to be higher to flat it more. cool video.
Great job. Works better than I thought it would.
Hey, give him credit, at least he was out doing something not sitting on your dead dupas doing nothing.
A paint can or watermelon on each would be cool LOL
Could hang a few shirts across the back wall and have a new merch line 😁
That’s Excellent Job Question will those cars look Wide when I get crushed will they fit on a tractor trailer without all the hanging
None that we have crushed so far would be too wide to go on a truck. Having that said I think you would need to push the doors in on a pick up or a Van to keep them from being too wide
I was going to say that you guys should keep the car off center to the hinges to reduce the leverage on the hinges 🧐👍 great job Anthony 😎
Absolutely awesome!💯🙌✌
Stack 2 smashed cars together on it and smash
I sure wouldn't want to be removing a few parts from a vehicle while it's sitting on that crusher 😱 That's a pretty small diameter cable? Just right for a snap one day. I'm surprised that the hinge is so high up. Likely half that height would work better.
Hey it has weight. That's what counts 😉 Not even lowering the hinge will help because all the mass is lost as soon as it hits the part of the car closest to the hinge. This is a coffee break project and not a piece being buildt to go into production. Pure männer fun stuff.
Yes you get it!
That was too cool. Great job guys 👍👍🇨🇱
Sickeningly satisfying. LOL. TOO COOL GUYS!
What happens if you stack 2 smashed cars on each other and resmash them together ? Could you get another foot shorter on each car? May be easier to stack?
Yes... this would be worth watching
Adding a bit more weight to the lid I think it would crush two cars at once.
I still think that the hight between the bed and the lid is a bit too high. The hood and trunk are not affected much by the crushing
We are planning on playing with it more soon
@@HardCoreFab You could also try tilting the car to the side and giving it one more smash. 😎
if the engines are still in the cars they probably turn intoo a wedge shape , maibe if the stack them with the noses in oposite direction the engines can embed themselfes in the trunkspace
Hard to believe y’all painted it before you tested it.
Got to look fresh for the first car
I painted my vehicles before I drive them too! LOL
That's awesome man!!!!
Hell ya looks fun !
You never sees to impress me from Belding cars to crushing them lol
Seize
@@brandonsciulli774 If you're gonna act like you're smarter than someone else and correct they're spelling, you ought to know how to spell it yourself. The word is "cease", As in "cease and desist"
@@bobd9193 hehehe
Stack 2 smashed cars then smash them again! Lol
Definitely turnd out cool. Could watch it work all day!
Love it!!! Good job!!
Got here by accident stayed for duration cause content!! Awesome guys
I'm impressed- but I think it would do better if the hinge was level with the table! also if you load the cars to the end of the swing it will make em flatter!😁
I was gonna ask him the same thing why did he position the hinge pin so high off the surface you figure it would be more stable if it were attached to the floor
@@pipegang6497 that's my way of thinking! I agree 100%.
The only reason for the elevated hinge is it allows for better momentum and keeps it from binding up.
If hinge was level it wouldn't be able to crush 'flat' it would leave the cars less crushed on back side. Therefore could not stack the crushed cars.
🤷 That's just my weird little brain. Who knows 😆🙌✌
@@mikethatguy27 you are correct, plus the engine is the most un crushable thing in the car, so having it level would not work
Well it does smash cars, I deny that but thats not all flat really! It just crushes roofs! For flattening it all out, you got to raise the platform on where the car sits, so flapper comes sandwiching car in between, but because your sitting ground is way below your hinges mechanism, it doesn't fully crush properly.
Its not hard to make, just a shorter panel to leave space for hinges to close in normally and just laying smasher more firmly and tighter on the crushed car. Aside from all above... Crushed cars looked in a real good shape though to be crushed, Except for last one!
You will most likely run in to the problem that the lever arm has to be double the length and double the weight to flatten it completly then.
Cause the lever gets momentum loss as soon as it makes contact , now the top part of the lever (fastest most momentum) makes contact first with a lower hinge the slowest traveling part would make contact first and would slow the smasher down giving it less momentum and less power.
It only has to crush the roof down to make it a level base to stack other crushed cars on top so they can be stacked on top of one another on the truck.
That’s wild!
Great video! Thanks for sharing.
Thanks for watching!
Did you get the go-pro out?LOL!
Lol Surprisingly it was unscathed
best thing that could happen to a ford
Yeah because the chevys are all gone rusted to pc or crushed
I drove a Chevrolet for a while… Then I got a job!
The panther platform cars are insanely reliable lol
Obviously a genuine millenial or the parent of one.😂
100%
Very well built. I love it!!!
Thank you!
Nice Job! I'm in my fifties now but when I was a teenager, I drew up plans for a crusher just like this design. One correction I see is you'll need to push the doors in so it will fit on a semi trailer correctly. Overall, I'm jealous that you have this crusher and I don't.
It's certainly an awesome attempt at building a home made crusher! Well done guys!👍😀
when the back plate slid into position, all I could think of is Jim Carrey saying "Like a glove!"
The use of kinetic stored energy is a novel elegant approach. Be mindful of forces on hinge point..and safety when its up
Great idea . Yup my thought was the pivot point why so high however .. flatten a car or 2 then double stack and flatten them with one on top of the other. Should have a good result ..
I am a happier man now and would love to see 2 cars stacked up for a second crush. Such satisfying entertainment.
That thing is merciless… I love it
What a satisfying crush guys love.love that beast u made
My old boss built a crusher like that but he used two hydraulic cylinders off a old grain truck he got in. It to this day works very well. Great job guys!
What a great build . Looking in from Ireland 🇮🇪
That’s pretty awesome
Car-nage! Awesome
Nice job 👍🏼 men!
Nice job !!! Need some safety shields on the sids
Very clever!
This is so satisfying
GEEEZ!!!that's awesome! That "wrecker truck" is a winch truck with gin poles, it's got oddly mounted poles but it's super cool
The bed is junk but the rest is sweet!
Good job Smasherman
That's Cool as Hell, I think Cowboy Car Crushing would Love this Crusher.
well done it keeps you going
sweet build, need to get the slomo guys in to catch the amazing power of this crusher
That would be fun!
Way. Way. Way cool.. liability insurance?? We don’t need no stinking liability insurance.
Awsome build you could probably fill the bit your lifting with winch with concrete that'll be interesting
Well that’s just awesome and now you can really stack those things up on the scrap trailer and send them down the road
That whole thing whips around a lot... Long as I don't have to be around it, you do you Pal.
Awesome
AWESOME!
I've worked in the salvage business for years. And I think thing is awesome!!! Does a out standing job! I'd Bee proud to have or use a piece of equipment like that. My hat off to y'all.
Thank you!
Thanks man!
That was awesome
Way cool!
Like any project you figure things out as you go. Like your hydraulics, perfect for testing. Late maybe upgrade to bigger motor and pump. If you wanted to make it mobile, put hinges on the struts and tower. Could use the winch to erect it at the new sight. Best of luck with it all.
Great job Lads....im wandering if you poke the door and pillers in with the loader or digger they'll fit easier on the load out rig..... maybe a sideways smasher......😉😎
Absolutely
Look like home make car crushing machine look great great work job
Super cool
Great job on your project. Looks like it works pretty darn good.
Thanks for the videos that was awesome
That last view from inside the car was crazy!!!😊
Yes it was!
I believe you might want to mount your snatch block on the lid or load.
This would allow you to increase the weight on the lid
Pancaked em. Should make for easy stacking.
You are a very handsome bearded man! Great job on the "Crusher". Ya'll be careful. That could hurt really bad.
Cool stuff. Always fun to smash some things. Happy Smashing!
You had me at “carnage one way or another.”
LOL
I highly recommend installing a vertical steel tube with the winch cable running through it just incase the cable snap it doesn't kill the operator
Very impressive, moves so fast you better be paying attention all the time to avoid a disaster.
Right!
I think i would load the cars with the engine towards the end of the smasher. I would also make another maybe 6"-10" plate to place on the platform under smaller cars to smash them even flatter since the hinge is so high. That or spin the cars around and hit them a second time might even work.
maybe have the hinge capable of dropping as it falls.
@@1stontario Would be easier and safer to just remake the hinge in such a way its adjustable and able to move up or down for thicker/thinner vehicles. That hinge needs to be rigid as possible to be safe as possible.
That looks waaay risky, bro! …but fun!!!
awesome
Wow that's cool fella
Thanks!
Add some cross bracing at the rear between the uprights and Maybe add a sloped ramp at the left to 3/4 of right side to ensure an even smash even when not placed in perfect
Cool!!!
Built the same type at Ray's in South Everett Wa.
Put concrete ecology blocks on the top hinge for more down force.
This is one of the most satisfying videos I have ever seen 😅🤣😂good stuff 👍
Glad you enjoyed!
Great Car crushers mate, nice build.
In one of my past jobs i had to work with a lot of smashed glass, please make sure you guys are at least using a P2 mask to reduce the risk of Silicosis.
Excellent idea! I'm a scrapper and I love this video. Man you gave me some ideas... gravity rules and so do you bro!
Right on brother glad you enjoyed it!
I would have liked to see you stack another on top, maybe a few after too.. Add some forms and fill the end with concrete! More can't hurt, can it?
6:25 that looked like a clean Vic!
Job well done. I crushing cars with a 2000 lb counter weight but it takes a little longer. You did good.