Part 1, How to make a silicone caulking mold

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 111

  • @jc_hz4196
    @jc_hz4196 3 ปีที่แล้ว +13

    Greta explanation, good tip on dumping the whole silicon tube. Super cheap and very affordable tip. Thank you.

  • @anthonyguillen2564
    @anthonyguillen2564 ปีที่แล้ว +7

    Nice job on explaining as much as you could most sorry all other people don’t like to mention the little tips and tricks a rite off the bat you did nice job I just started using the silicone tubes and a very bad experience with corn starch the water and soap work great thanks again.

  • @lenny108
    @lenny108 8 หลายเดือนก่อน +1

    0:17 This type of silicone is no more available in normal hardware stores. They only sell acryl tubes.

  • @neilhenriques9435
    @neilhenriques9435 ปีที่แล้ว +3

    Thank you for the tips as to what type of silicone to buy.. Good job

  • @mrpipestache2423
    @mrpipestache2423 11 หลายเดือนก่อน

    Is there a way to do the reverse and have your finished product be the silicone? Like make a household products detailed mold of your real hand, and then use the silicone to make a silicone lifelike cast of the hand?

    •  10 หลายเดือนก่อน

      you can coat the item with separator like to spray with silicone oil. Then place the item inside some box or so like form area and cover the 5 sides with oil separator too. Best to fix the item by two wooden pieces or so. Fill the first half (bottom) of item in the form area with resin epoxy, let it harden. After a day, coat the hardened epoxy with silicone oil spray too, make sure the item is well coated too. And finally fill the box or form area with resin epoxy - the replicated item should be completely submerged, the resin should make a layer a little more above item. Let it harden again. Now you could easily remove the new form from boxed area and divide it into two pieces, halves. Remove the item. Now you can fill the form with silicone to make infinity number of copies. Through one of the two canals created by wooden supports of item you can press more silicone, the air bubbles will leave same way during hardening. With wax or similar materials this works well too.

    • @mrpipestache2423
      @mrpipestache2423 10 หลายเดือนก่อน

      @MilanWolfl I'm trying to make fake silicone body parts using my friends. So this won't work unfortunately 😕 I'm looking for a way to make the end product silicone like a life cast of the persons hand or foot or arm so it looks and feels somewhat real when it comes out the mold. I need the end result to be silicone. I live in an apartment so I was hoping I could do it safely and without spending a lot maybe using home found products that aren't too pricy. Needs to be skin safe and not put off any bad smells.

    • @mrpipestache2423
      @mrpipestache2423 8 หลายเดือนก่อน

      @jazzyj2182 what makes you think my intentions are sexual? Think before you post please.

  • @learningwithoutlimits
    @learningwithoutlimits 2 ปีที่แล้ว +3

    Waoo great. I was making my fondant topper and was wondering to preserve my hard word by making mold to help me next time. Any idea can I use this technique for hardened fondant or air dry clay figure

    • @sombrerocordobes2256
      @sombrerocordobes2256 2 ปีที่แล้ว

      Go to GEO Sustainable channel; he has a ton of useful information and tutorials on homemade silicone molds, including food safe.

    • @janetanderson5116
      @janetanderson5116 2 ปีที่แล้ว

      Don't kno if this is to late because u asked 6 months ago but you can get food safe silicone and use cornstarch for casting fondant decorations

  • @PaulineCorlis
    @PaulineCorlis หลายเดือนก่อน

    Do I have to use Dawn soap

  • @kawansculpture
    @kawansculpture หลายเดือนก่อน

    in my experience the original piece you making mold from like you used plaster must be completely dry , the silicon create heat , then it will cause bubbles in the mold , if your master piece is plaster , thank you for your amazing work .

  • @MrBikedrummer
    @MrBikedrummer ปีที่แล้ว +1

    What would I do if I want to make a cast of a real human hand? Can that be done this way?

    •  10 หลายเดือนก่อน +1

      make a mold by another materials like clays, divided into two pieces, and let it harden separated without the hand in the mold? Its not possible to stay with no movements and shaking for so long time of hardaning... But you have to test the material for a mold, if it does not shrink or change the shape in corners.

  • @capcloud
    @capcloud ปีที่แล้ว +1

    do you know why the other silicone types don't work?

  • @rafaelcarmona4461
    @rafaelcarmona4461 5 หลายเดือนก่อน +1

    You did a phenomenal job of detailing in this Presentation. Thank you soooo much for this.
    Respectfully, ralph

  • @DocVore
    @DocVore 2 ปีที่แล้ว +2

    Great video. Do you know why you need to use soap on the silicone?

    • @hopibreton2124
      @hopibreton2124  2 ปีที่แล้ว +4

      the soap prevents the silicone from sticking to your hands, wether or not your using latex gloves to process

    • @douglasflores1462
      @douglasflores1462 6 หลายเดือนก่อน

      @@hopibreton2124
      Nope, it is to catalyze the silicone, the soap you use must contain glycerine in order for it to catalyze the silicone

  • @hotamblog9586
    @hotamblog9586 4 หลายเดือนก่อน

    Is this construction silicon .thank you

  • @liberiabd
    @liberiabd 10 หลายเดือนก่อน

    Its New for me, great , next mold i use your Idea 😊 thx

  • @Omri.Collects
    @Omri.Collects ปีที่แล้ว +2

    Excellent tutorial for diy mold making! Will def give this a go.

    • @Omri.Collects
      @Omri.Collects 8 หลายเดือนก่อน

      @jazzyj2182 This is a tutorial for how to make a diy silicone mold. 🧐 I’ve no idea what your comment has to do with that. I needed a replacement part for my suitcase, unless you’re going to buy me a new suitcase, keep your unhinged and uncalled for comments to yourself.

  • @MunemShahariar-u3w
    @MunemShahariar-u3w ปีที่แล้ว

    Can I do metal casting in this mould?

  • @shelbestowe4802
    @shelbestowe4802 ปีที่แล้ว

    Is this reusable and if I'm using clay can I bake it up to 250 Fahrenheit

  • @lenny108
    @lenny108 8 หลายเดือนก่อน

    Apparently silicone 1 means that it is acetic acid based silicone?

  • @danaangela6577
    @danaangela6577 7 หลายเดือนก่อน

    Is the mold soft enough to fold it inside out ?

    • @danaangela6577
      @danaangela6577 7 หลายเดือนก่อน

      Is it streachy?

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      3:14 ​@@danaangela6577

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      I don't want to sound stupid but what is it used for

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      ​@@danaangela65774:27

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      4:49

  • @lenny108
    @lenny108 8 หลายเดือนก่อน +2

    1:04 Seems this brand of silicone is nowhere else available than in SF.

  • @liberiabd
    @liberiabd 10 หลายเดือนก่อน

    I make a little test and everithing is fine. Must wait 24 h until tomorow😢

  • @jackieprice7306
    @jackieprice7306 11 หลายเดือนก่อน

    Where is part two?

  • @-Harambe
    @-Harambe 2 ปีที่แล้ว +2

    Is it safe to breathe the odor that comes off the silicon caulking tube when working indoors?

    • @amytaf2387
      @amytaf2387 2 ปีที่แล้ว +1

      Someone else def recommended wearing a good mask.

    • @tonygladman8819
      @tonygladman8819 7 หลายเดือนก่อน

      Silicone is hazard to health!!!! IDIOT

  • @ved-5522
    @ved-5522 ปีที่แล้ว

    Can we use again this mold

  • @MC-bc2ew
    @MC-bc2ew 2 ปีที่แล้ว

    can I use this to a mold somthing I created with air drying clay?

  • @jeanninetamblyn7625
    @jeanninetamblyn7625 ปีที่แล้ว

    Can I use polymer clay in this silicone mold? I want to make a few molds of baby dolls that I have to cast them in clay. Would this work for that???

  • @Ten1alone2
    @Ten1alone2 ปีที่แล้ว +3

    Is this body safe? I'm asking for a friend 😁

    • @Ten1alone2
      @Ten1alone2 8 หลายเดือนก่อน

      ⁠​⁠​⁠​⁠@jazzyj2182so a custom hand mold is “sexual immortality”? 😅

  • @dannycherry7809
    @dannycherry7809 2 ปีที่แล้ว +2

    Could you do this on a real hand

    • @myjourneytotruth
      @myjourneytotruth 2 ปีที่แล้ว

      Besides it getting stuck on your hand it could take 24hrs to dry up...care to put your hand through that statue phase

    • @dr.dahshan
      @dr.dahshan 2 ปีที่แล้ว

      @@myjourneytotruth I want make mold from my foot, it's easy or not brother??

    • @hopibreton2124
      @hopibreton2124  2 ปีที่แล้ว +1

      @@dr.dahshan you cant do this on real body parts. however, you can cast a body part in Alginate first, get a plaster positive, then do the silicone over that plaster cast.

  • @craigcraigster5605
    @craigcraigster5605 2 ปีที่แล้ว +3

    Do you need to use a mold release at all? Great video

    • @randijipson603
      @randijipson603 7 หลายเดือนก่อน

      She said no in the video 😊

  • @cchemmes2096
    @cchemmes2096 ปีที่แล้ว +17

    I really could use deeper explanation why only this one type of caulk 100% silicone works to make a mold, & why all these other forms do not. Only because you say so? Do you mean they do not work for this method? Would they work if you thin layer them? Why are we putting the silicone in soap water? No explanation? Thanks.

    • @TheyStoleMyHandleAgain
      @TheyStoleMyHandleAgain 7 หลายเดือนก่อน +2

      If it's not 100% silicone, it will never "harden" Putting it in the water causes it to release the acetic acid and start the "hardening" process.

    • @ashleigh33391
      @ashleigh33391 4 หลายเดือนก่อน

      She literally explains the soupy water within 2 mins of the vide 🤦🏻‍♀️

  • @sucoyiaali
    @sucoyiaali 2 ปีที่แล้ว

    would this be good with cement as well

  • @bibi-decaffinated5586
    @bibi-decaffinated5586 3 หลายเดือนก่อน

    Great content. A lot of love to you from the Beautiful Islands of Trinidad and Tobago 💞.

  • @eon1635
    @eon1635 ปีที่แล้ว

    Would it be okay to make a silicone mold out of this neutral silicone for a broken lipstick?

    • @red2965
      @red2965 ปีที่แล้ว +2

      If that's what you wanna call it yes, just make sure it's cured gòðd no bad smells comment from it.

  • @54321Judith
    @54321Judith ปีที่แล้ว +3

    Instead of cutting a straight line, why don’t you cut a curvy line so the registration marks lineup better and hold together better?

  • @airamaria1597
    @airamaria1597 ปีที่แล้ว +1

    What did you do to prevent the silicone from sticking with that hand figurine that you used

    • @misteryudonnome
      @misteryudonnome 7 หลายเดือนก่อน +1

      Vaseline or petroleum jelly. Just my guess... I have no idea and didn't even watch the video. Hope I helped! 🤞

    • @airamaria1597
      @airamaria1597 6 หลายเดือนก่อน

      @@misteryudonnome Thank you 🫶

  • @NooralZeraat
    @NooralZeraat หลายเดือนก่อน

    Great thanks 👍🙏👍🙏🎉❤❤

  • @SCPVIDEOPRODUCTION
    @SCPVIDEOPRODUCTION ปีที่แล้ว +2

    Why is nobody showing the cast from the mold?

  • @jst1man
    @jst1man 2 ปีที่แล้ว +4

    Sorry, but the different silicone 2 will work. It just has to air out. Also you don't need dawn. You can use glycol as a substitute for dawn.

    • @mebobtheone
      @mebobtheone 2 ปีที่แล้ว +1

      Problem is Type 2 has additives like latex to keep flexible and resin will react badly if doing resin casting.

    • @rayst.2934
      @rayst.2934 2 ปีที่แล้ว

      Thanks for that tip because I was going to use resin. Your method is so simple and easy and I was trying to make a box to put the mold into with hot glue and it just didn't work too good for a two-part mold you have to use clay on one side but this is the best tutorial I've seen yet thank you save me a lot of money and time and headaches

  • @addicted2monster88
    @addicted2monster88 7 หลายเดือนก่อน

    Okay. But now say you wanna do a whoke arm. Like for Halloween props. Now that you have the mold, could you use the same silicon to make a jiggle arm? Or heck even the same to make a hand? Severed hands are always good props cuz of there size

  • @joee7626
    @joee7626 ปีที่แล้ว

    But I'm not sure, does it need to be clear #1silicone? You're explanation at the the beginning didn't specify.

  • @Aravis217
    @Aravis217 ปีที่แล้ว

    Does this work for resin?

    • @yrunaked4
      @yrunaked4 11 หลายเดือนก่อน +1

      I have used this method with plastic model parts with no problems.

    • @Aravis217
      @Aravis217 11 หลายเดือนก่อน +2

      @@yrunaked4 ok thank you very much. I do really appreciate your response!😊

    • @Aravis217
      @Aravis217 8 หลายเดือนก่อน

      @jazzyj2182 you know preaching to people who dont ask, really turns people off from what youre spouting. How well do you know the rwligion that you are spouting? For instance- how many of each animal did Noah take on the ark?

  • @cieramesser4906
    @cieramesser4906 3 ปีที่แล้ว

    Will it work for resin

  • @kellyjean4981
    @kellyjean4981 ปีที่แล้ว +1

    Thank you for sharing

  • @RededicateYrLife
    @RededicateYrLife ปีที่แล้ว +1

    Thank you so much for this alternative solution

  • @Tinker250
    @Tinker250 10 หลายเดือนก่อน +1

    the fact that I didn't buy 100 percent silicone and I just am watching this viddeo :(

  • @elenapaliceanu9004
    @elenapaliceanu9004 2 ปีที่แล้ว +1

    This was the hardest thing I had to do in my life. After ruining half the kitchen, sponges oil sugar as it was sticky and it went everywhere, after an hour I threw it away along with everything else. After finishing clearing up and putting the last thing in the bin, I noticed that it wasn’t sticky anymore, only in the water it was, and to my hands. Anyway I took it out again and it was not sticky anymore, suppose it needed a trip to the bin first. I will leave it overnight and tomorrow and have a look after 2 days to see if it comes up as suggested. With all the things ruined and the price for the silicone and my time, it is muuuuuch cheaper to get one already made. But it was an experience.
    Hope this helps someone.

    • @quazimodo1973
      @quazimodo1973 ปีที่แล้ว

      I recommend just watching a few different videos, practice makes perfect

    • @techtinkerin
      @techtinkerin ปีที่แล้ว

      Not really 😂

  • @Mrs.Frankenstein
    @Mrs.Frankenstein 2 ปีที่แล้ว +3

    Make sure to do this in a well ventilated area or outside even. The smell is super strong so might wanna wear a mask if you have respiratory issues!

  • @omarjassar4650
    @omarjassar4650 5 หลายเดือนก่อน

    Good job , Give yourself a hand ✋

  • @Carnivorous-Vegan
    @Carnivorous-Vegan 2 ปีที่แล้ว +3

    And of course, allI have is type-2 in the garage... Thanks for the warning.

  • @tomelyas8146
    @tomelyas8146 ปีที่แล้ว +4

    I did it and made a mold in less than 2 hours with some bubbles on the surface. .cheapest way. But the smell was terrible.

  • @ShawnMarcelino
    @ShawnMarcelino 29 วันที่ผ่านมา

    The zhit never cures buy the two part mix for making molds😊

  • @reginr
    @reginr 2 ปีที่แล้ว +1

    THANKYOU!!!!!!

  • @larryvisgar7115
    @larryvisgar7115 2 ปีที่แล้ว +2

    I just tried this and it didn’t work at all

  • @ChannelSettingsTvcode
    @ChannelSettingsTvcode 2 ปีที่แล้ว

    Interesting

  • @Elkallaf
    @Elkallaf ปีที่แล้ว

    good

  • @KJ-Serene
    @KJ-Serene 2 ปีที่แล้ว +1

    We're only getting half a story here. If only we had seen the mold being used for, say, a resin casting 🤨

    • @leahspagrud
      @leahspagrud 2 ปีที่แล้ว

      Did you use type 1 or type 2?

    • @hopibreton2124
      @hopibreton2124  2 ปีที่แล้ว +3

      :) I did make another video showing the use of the mold for a beeswax casting (I was making a candle). It would work the same with resin. I dont use resin much, sorry. but I can say that resin leaks out of silicone molds very easily. My recommendation for that is: follow my other demo for casting into silicone mold, but after you wrap the string around it, then you can dip the seam of the mold into molten wax. the string helps hold it there. the wax makes a cool seal that helps prevent leakage.

    • @genericpvp4161
      @genericpvp4161 ปีที่แล้ว

      @@hopibreton2124 pro tip right here

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      Yeah I would love to see you

    • @LyndaDouglas-c9m
      @LyndaDouglas-c9m 5 หลายเดือนก่อน

      Somebody please tell me what it's used for

  • @gerry.shafer6101
    @gerry.shafer6101 2 ปีที่แล้ว

    Thanks. Lots. !!!

  • @otmargreb6110
    @otmargreb6110 ปีที่แล้ว +6

    By the time i bought these products, i could have bought a cheap mold kit from DIY... Just saying!

    • @quazimodo1973
      @quazimodo1973 ปีที่แล้ว +2

      They're not cheap those kits.... This is actually a money-saving hack and works great with the right technique

    • @k_ka_chi5413
      @k_ka_chi5413 ปีที่แล้ว

      ​@@quazimodo1973I'm new i wanna learn how to make it 😢can you teach me

  • @Thatdude1281
    @Thatdude1281 2 หลายเดือนก่อน

    Mmmmmm squeezing and folding . Squeezing and folding …… then rotate ! Daaaang . That’s the good stuff. You got a snap ? 😏

  • @jaisinghkumawat282
    @jaisinghkumawat282 2 ปีที่แล้ว +3

    What are these liquids, you used to pour silicon