Grand Prix GTP w/ ZZP NIC Cam + Cold Start (Choppin)
ฝัง
- เผยแพร่เมื่อ 25 ส.ค. 2024
- MOD List Below
If you enjoyed the video PLEASE SUBSCRIBE, any questions please ask.
MOD List
Gen V Top Swap
ZZP NIC Cam
LS7 Lifters
NorthStar Throttle Body / LQ4 MAF
Roll Master Double Roller Timing Chain
Comp Cams 136lb Valve Springs
ZZP Stainless Valves
60lb Deka Injectors
ZZP 1.65 Rockers
Porter Heads
Ported LIM
ZZP Power Logs
ZZP 3.3 Pulley
AEM Full Pump
ZZP 7in Push Rods
Custom Tuned PCM
ZZP Cold Air Intake
Triple Edge Performance Stage 2 Trans
ZZP Belt Wrap Kit
ZZP 3in Down Pipe No CAT
Powdered Metal Connecting Rods
180* Thermostat
8 Rib SFI Balancer
Ducks like sorry excuse me pardon me
That thing sounds EXCELLET! The 3800 just might be the most underrated engine ever. Everybody always wants the 700 or 800 or 900hp whatever, but when you think about it, this engine is 370 pounds lighter than a hellcat engine. There are adapter plates you can get from Australia to bolt it to awesome transmissions. And when you take them apart, they're like LS engines shrunk down. You can get a 3800 core for less than the cost of some used coyote cams.
where do i get the adapter plate for the transmission? can i have more info on this?
@@peytonfedler5887 You're looking for a Malwood Holden V6 to T56 adapter plate.
@@Dr_Xyzt ok..... now im convinced I wanna build a Buick Park Ave ultra.... if i could swap a proper stick shift in there it would make it all worthwhile
@@LaChona420k Uh, it doesn't work that way. Park Avenues are FWD.
@@Dr_Xyzt wait a sec, the Grand Prix gtp was RWD?!
The chicken or whatever that bopped last was just perfect. Car sounds nasty, good w
the duck vibin
Duck was like nah y’all wildlin
This sounds amazing.
That sounds awesome! I miss mine every day. That sounds so much better than my Challenger, no joke. (Not trolling or lying, I'm dead serious.)
You gotta post a roller of that choppy dog.
Hopefully soon, getting ready to go intercooler and e85.
fire
Sounding like a V8 bro....
Getting ready to install a cam on my Bonneville, did you have to pull the engine when you installed your cam? Or were you able to leave the motor in?
I pulled the entire engine out, these engine are really easy to pull. I had it out and just a few hours.
@@SyNFuLLjI have 2008 base grand prix trying to get it to sound like that
Which valve springs do you have?
136lb Springs, Mod list is in the description.🤘
Did you have to change pushrod length to run this cam?
Yes I did, I think it ended up being that ZZP recommended. 7.00 push rod
@@SyNFuLLj cool thanks
What have you done to the exhaust?
ZZP Power Logs
ZZP Stainless Cross Over
ZZP 3” Down Pipe No Cat
3” Cherry Bomb
Gone e85 yet ?
Im currently working on pump/rewire kit so i can drop to a 3.0
I have everything to do it. But e85 isn’t very close to me to make it worth it. Maybe down the road ill change my mind.
@synfullj6013 understandable! Thankfully it's like 5iles from me .
Cheers man ! Let's keep the 3800 alive!
@@SyNFuLLjSee how much it is to buy barrels to store at home?
I’m running a 3.0 on 91 currently, intercooler and headers, gen 5 blower north star throttle body lq4 maf but honestly I should have a cam upgrade to be running this 3.0,, it makes max boost with just a slight blip of throttle, full throttle the boost is pretty much useless as I’m reaching max boost long before full throttle, so just keep that in mind if you dont have any other supporting mods your not gonna gain more hp by dropping just build the boost faster
What’s idle set at
800ish give or take.
@ 0:15
You had to get it tune?
I did not have it tuned after install of the NIC cam, still ran fine. But I have since then gotten it tuned.
How much did it cost for the cam installation?
I did the install my self, when i bought the cam is was around $300 something. Not including the supporting mods needed, retainers, 136lb springs, locks and double roller. So add another 200-300 for all that give or take.
@@SyNFuLLjso you're talking $600 for supporting mods and the cam??
What kind of cam is it
ZZP NIC Cam
Horsepower?
Honestly I could not tell you. Ive never had it dynoed. Im getting ready to add a bunch more upgrades tho. So hopefully after that I can get some numbers and post a new video.