Lifan KPX 250 - ECU Remap - Test ride
ฝัง
- เผยแพร่เมื่อ 15 ต.ค. 2023
- If you received your KPX and have idle issues or a slight hesitation in the throttle, get it remapped for free. Just ship your ECU direct to Lifan America. Please enclose your ECU and a note with your return address so they can map and send it back.
American Lifan
9272 Hyssop Dr.
Rancho Cucamonga, CA 91730
(909) 605-6999
This isn't a scam, you can reach out directly to Lifan to verify prior if you'd like: contact@americanlifan.com
#KPX250 #Lifan #LifanAmerica #LifanKPX250
![[Watch Party] APL 2024 Bacon Time Vs Hong Kong Attitude ชนะเข้ารอบ](http://i.ytimg.com/vi/ikUfW81sDaw/mqdefault.jpg)
Thank you. I contacted Lifan and explained my throttle issue on my new bike. that "hesitation" as you called it. They promptly sent me their shipping address (same one you gave) and I sent my esu/efi module to them last Tuesday, Cost about 10 bucks to ship. Got it back from them today, they did not charge me a penny. Not sure what they they changes but the bike is awesome. No hesitation, no quick throttle pop and die at low rpm, the idle is a tad higher maybe 200rpm and is very smooth now. I did mention to them that I was at low altitude and not sure if it was running lean before but the smell from the exhaust is gone now.
Ya I'm loving that they are actually working with owners after purchase . They've made a fan out of me.
Thank you so much for this! Your channel is incredibly helpful brother. Still hoping to see you do valve adjustments tho ;) I bought the special wrench and it's still a pain! Done it twice so far. About 1250 miles on mine and riding daily as my commuter in south Florida. Enjoying the bike a lot so far
You should be good for awhile then! I did mine but was so annoyed I didn't video it :P. I'll video it when I do my buddy's bike.
@@dadbodbikers this bike is still new to me. I have a little over a hundred miles. When and why is a valve adjustment necessary? Please and thank you!
@@earl-tf4qc often, the Chinese motorcycles are shipped with valves too tight.. particularly the lower quality bikes. Ours weren't far off when checking . But it's worth doing to maximize horsepower and longevity. No harm in waiting until it has a few hundred miles if it's running good to check them.
Unfortunately, I had the same throttle position problem with my ECU and I sent it in. They did send back an ECU (I didn't mark mine that I sent in so I'm not sure if i got my same one back). The one they sent back seems worse than the one we sent in. Twisting the throttle a small amount causes the engine to drop out in any gear or at idle. I'll try again with them....
Definitely sounds like your tps isn't quite positioned right.
@@dadbodbikers Is there a specific adjustment parameter to get it just right? I can see there is a slot on it so it can be turned some.
@@stephenlnoe just adjust it each direction to see if it gets better.. there's no perfect measurement.. I can take a picture of one of mine
Does it seem to run a little less lean? Seems like it has a little more Brraapp if that makes sense
I would assume but they haven't given a straight answer on exactly what they changed.
Change the exhaust, to a free flow one! Also change the air filter. My one tops at 87 mph
Did you remap your EFI when doing that. What exhaust did you use? 87 on the speedo ro gps?
Did you remap the ecu after?
@@dadbodbikers i imported it from Indonesia. Exhaust - Norifumi torq, which cost me 300$
You can fit one, which is easily available to you. Yes yes! I retuned the ecu! From Rasel Industries. They produces Lifan bikes locally
@@inhumanfilth681 You have to have a lot of patience. You have to retune the ecu again and again. sometimes I felt like dropping the bike.
@@dadbodbikers exhaust -(Norifumi torq)
Imported from Thailand 300$ only
Where do you guys ride at? I have a tbr7 as well
All over north Georgia and sometimes TN and NC.
@@dadbodbikers nice, I’m pretty close to the TN state line in Kentucky
@@Highvoltage2332 We just did a 850 mile trip all the way up into Kentucky on these bikes: th-cam.com/video/auOL4U3G-8A/w-d-xo.html
@@dadbodbikers that’s awesome! What part did you make it to? I’m around the Williamsburg Corbin area
@@Highvoltage2332 we stayed in Daniel Boone national forest one night...then campbellsville.. then did makers mark distillery on our off day before cannonballing home 370 miles in one day :)
Is it possible to take the baffle out of the exhaust?
haven't tried.. someone else.might have by now.
@@dadbodbikersMaybe but not that I've seen on TH-cam . Have you tried to do an exhaust swap out ? Can you try to do a vid on a swap maybe ?
@@st3v3n_j12 I've got a line on a few and am just trying to do it the right way (with adjusted mapping). It may take some time.
Great. How much was it
~$3000 brand new.
china king