#1 Arctic Cat Issue!! - 400 Auto 4x4 TOP END Problems
ฝัง
- เผยแพร่เมื่อ 24 พ.ย. 2024
- Complete Disassembly of a 2003 Arctic Cat 400 4x4 Auto ATV Motor.
Video 1 of 2.
Link to Puller: www.ebay.com/i...
Flywheel Kit: amzn.to/2ISJmD8
Belt: amzn.to/2J1sDgB
Carb Kit: amzn.to/39aF3h1
Battery: amzn.to/3lUc197
Tires: amzn.to/3nFcj46
Oil Filter: amzn.to/3nFcj46
Feeler Gauge: amzn.to/36UsROK
Second video is: • #1 Problem - Check Fly...
More Arctic Cat service videos:
• Suzuki Eiger 400 - Top...
• HOW TO - Arctic Cat 40...
Patreon / midnebraskamotorsports
Instagram / midnebraskamotorsports
Check out my eBay store at stores.ebay.com/midnebraskamotorsports
We Disassemble: Clutch Head Valve Cover Cylinder Piston Stator Points Rotor Magneto Generator Alternator Coil Camshaft Cam Chain Tensioner Rocker Electrical Cases Bottom End Case Set Transmission Shift Drum Fork Gear Shaft Flywheel Starter Idler Clutches Bearings U Joint Yoke Driveshaft Shaft Assembly
Hello, great videos, thanks for your help. I got mine all back together and runs great. Did a complete rebuild engine was brought to me in pieces. Went forward great, put in reverse no problem hard to get back in drive. Did that a few times now stuck in Reverse. Please Help!!!
@@MidNebraskaMotorsports You are the Man!! Idk why I did not think of that. Didn't really Kno I could. Took me about 5 mins and now seems to shift great. Thank you very much for your knowledge and your videos. I have definitely liked all of your videos that I watched and subscribed!!
No, I didn't like it. If your intention is to show how to do, you may use a different film technique.
Excellent
So is it the same for the 2001 cat 500 automatic?
Do you have all the torque specs for all the bolts / nuts for the 500 I listed above?
Do you have a video of tear down of manual engine
What was the issue with this motor? I have the same motor. Adjusted the valve springs and ran good. I put everything back together and nothing. Just cranked but wouldn’t fire.
Do you have a video showing an Artic Cat piston change?
Hi, I have a question. I just rebuilt top and bottom end and I think it might be a little bit out of time. Its running perfect. But I adjusted my idling. When I first crank it over. It forward right up. And its still running. Perfect but it sounds like it's turning my belt. Slowly but it still drives good. But when I put it in gear. It will jump to. In any gear, it will jump. But it's running properly. It could be a little bit out of time. Any help? Will be greatly appreciated. And thanks your videos have been very helpful but wish you would make a video. If you put in it back in time. I got the motor back in time. But I don't know where to set the. Timing crank properly thanks
I meant to say. Timing cam I don't know if I got the timing cam sitting in the right position.
Is there a gasket on head cover or do you just use gasket maker
Can you show how to set timing please e
Great video idea. Hit that subscribe button so you are notified when we get one posted. Thanks for watching and for the comment. Let us know if you need anything else: www.ebay.com/str/midnebraskamotorsports
Do you have an intake manifold for a 400 arctic cat 4x4 same motor your tearing down in the video.
I have a 2004 arctic cat 400i with the same engine and it has a constant metallic noise when running, doesn't burn oil, stays with all rpm changes, but doesn't necessarily get any louder, it's more annoying than anything and quad runs good. I am a small engine mechanic by trade and preliminary inspections haven't found any telltale areas. Any ideas before I start disassembly?
Kinda like loud tick, much louder than a typical valve clearance issue
@@danknight1668 your about to be burning oil, mine had the same tick, ran perfect then all of a sudden it started dumping oil down the tailpipe, i havent got it apart yet, but its looking like an oil ring on the piston is broken.
I'm not a mechanic so this is probably a dumb question but why are there 4 valves? I thought there were supposed to be 2 valves intake and exhaust.
Do you have a video showing the rebuild?
I have a 2007 artic cat 400 with 59 hours on it. It sit for a year and was not smoking but now it smokes so bad I can't ride it. Would the rings face seized? If so can I replace by taking the piston to top dead center and tearing off the top end?
We’re did u buy the bottom end rebuild kit for that motor I have a 04 auto 400 4x4 and can’t find a bottom end rebuild
I also have a 400 manual 4x4 if u could give me a price on just the bottom end for the manual it would be awesome
When I turn the shaft running thru the motor it is not smooth I’m thinking a bearing is out but everything else looks good gear wise
That flywheel is junk, the MAGNETS not weights, have in glued from the flywheel and it's no good, you can't glue them back on because it is a harmonically balance part. Replace it!!
Get a soft face hammer