I finished this project and I follow how you build it. However when I press it, the bulb will not permanently off and the bulb will light again a few seconds later. Is it possible that this design will permanently off if I touched it and permanently on if I touch it again?
yes you can ....you can use 5v or 12v spdt relay...the choice is yours....If your power supply is 5v...you can use e5v or if you power supply is 12v use 12v relay...
That is a linear voltage regulator, which means it provides 5v from the 9v battery, while trashing 4 out as heat, nearly 50% of waste. I agree with other who commented, a simple 5v transformer hooked up directy to the ac mains in 95% efficient, plus you don't need the battery. This "How to" is more of a "look what i did" than a proper guide. Thumbs down, sorry bro.
First of all thanks for your comment.... 1. no voltage regulator is used in this project 2. In your comment you mentioned to use a 5v step-down transformer..for more efficiency.....I totally disagree with point...instead of using transformer I will suggest use a 5v mobile charger or adapter...which is more efficient with respect to transformer.... 3. you mentioned to use transformer which is efficient about "95%" Also I disagree with this point..because you can't find a transformer which is efficient 95% because the efficiency of the transformer depends on many factors...like i^2R loss,iron loss etc...
I didn't realize it was a mosfet instead of a voltage regulator. But I must disagree, using a 9v battery is inefficient even if you get a cheap 80% on your transformer.
shock nahi lagega aap sirf dc circuit pe kam karaahe ho...lekin accha relay use karna.... also remember 220v is very dangerous to work if you not suitable with 220v ac then pleaase don't do this... Also if want to do that then do it at your own risk....
hi. why are you using 10k resistor? Is it because of 9v supply? If i am tu power it up with 12v, would i need to add bigger resistor?
Hi bro nice video.
Could it be applied to bike with 12 v source and without key use. If so, which parts need to change or same ?
Pls reply, thank u
i have adpater with output 8.5v..which relay should i use? 5v or 12v
12v
Can i use 3v battery
Looks like you are driving a 12V DC relay with 9V DC battery, did you have any issues
nothing......
I wanna applicated to metal door, can be?
touching switch means only touch the metal to operation, not touching the TWO poles. David.
One question, why do we use a 9v battery when we are already using 220v from supply
9v battery is used to drive the circuit which control the relay...instead of 9v battery you can use 9v adapter....
Oh thanks😊😊
bhai is touch switch ko hm directly use kd skte. 9volt k bdle 220v
ha lekin apko acchi power supply use karni hogi....nahi to shock lagne ki chance hai....
koi nhi bhai electricians hun wire se acchi phachaan h meri
I finished this project and I follow how you build it. However when I press it, the bulb will not permanently off and the bulb will light again a few seconds later. Is it possible that this design will permanently off if I touched it and permanently on if I touch it again?
These circuit is capable to permanently on & off the load....there might be some problem...please check it again...
Nice Sir sir 220 v ka kam krty ho ya nhi
yes you can control 220v appliances...
dear sir. can you please tell me, which kind of relay? 5v or 12v dc?and can i use this circuit for controll my automatic water pump?thanks so much.
yes you can ....you can use 5v or 12v spdt relay...the choice is yours....If your power supply is 5v...you can use e5v or if you power supply is 12v use 12v relay...
Balf kitane ganto tak chasta h
I also made one but mine is turning off automatically after five seconds what is the problem in it ?
same problem
you can do both buttons in one !!!! WE CAN ??? thank you ,merci
Hii bro its 2022 can you please re upload the circuit diagram.. and all hidden features
Please send link to buy all electronic components used in the circuit
check description
cannot open the wirindiagram link??
I want to make this can you please send me circuit diagram
Supprot power 12volt?
For 12v use 12v relay... That's it
yeah ... make a 10k transistor there is no problem to give 12volt power
I tried it successfully, but after OFF a few seconds ON before touching what was wrong?
@@TheBreakoutTraderAKASH after, why is OFF before touching ON? .... is there something wrong with my circuit?
nice wrk bro.... kinta watts tak load sopport kerlega yeh circuit?
500 watts...
How much cost to make the Circuit
under 50rs...In my case....
Good 👍
not working....
i connect every thing as yours..
still not....
I tried it successfully, but after OFF a few seconds ON before touching what was wrong?
accha apna batai ki shok lagna ki dar he....to ma kea tester se check nahi kar sakta....pcb plate ko
of course you can check it....
no heat sink for the mosfet
Haqiqiy moshinalarga qoysa bolami
Hi my friend, it's not good here with me. When I turn it off, it spends a few seconds and he calls again! I do not know what is happening!
that means the circuit is automatic triggering......what kind of power supply you use ....??
Same problem i use 12v adaptor 1amp
Without PCB bord remote control fen of on so plz
kya ham 12 v riley solar panels ko jodakar ato on of kr sakte hain kya
you mean aap solar panel ko relay ke help se operate karna chate hai.......thik hai...
kya aap bistar se baayenge please kya aap karna chate hai....??
bhai ham 12 volt solar panels ko 12 v riley jodakr aur usko 12 v battery jofakr dinme charge aur ratko ato on ho sakata hain kya
ok...I will make a video on this topic...thanks for your idea....
i like it channels bro thank you very much....
jaldi banavo bhai
Anil Jangle
we need to see full circuit diagram
Of hone par .. automatic on ho jata h ......
very nice video
"Screet key" for your car or your cycle motor, maybe
Nice & practical.
For me it does not make much sense. Touch controlled devices are not reliable and unpredicipble.
Readme .txt cute wier Short for best sens
Readme .txt
Mosfate ka name nahi likha
Thanks
why not use a simple npn transistor. more cost effective
one single npn transistor will not work for touch to on & touch to off .....circuit
Very nice
That is a linear voltage regulator, which means it provides 5v from the 9v battery, while trashing 4 out as heat, nearly 50% of waste. I agree with other who commented, a simple 5v transformer hooked up directy to the ac mains in 95% efficient, plus you don't need the battery. This "How to" is more of a "look what i did" than a proper guide. Thumbs down, sorry bro.
First of all thanks for your comment....
1. no voltage regulator is used in this project
2. In your comment you mentioned to use a 5v step-down transformer..for more efficiency.....I totally disagree with point...instead of using transformer I will suggest use a 5v mobile charger or adapter...which is more efficient with respect to transformer....
3. you mentioned to use transformer which is efficient about "95%"
Also I disagree with this point..because you can't find a transformer which is efficient 95%
because the efficiency of the transformer depends on many factors...like i^2R loss,iron loss etc...
I didn't realize it was a mosfet instead of a voltage regulator. But I must disagree, using a 9v battery is inefficient even if you get a cheap 80% on your transformer.
yes...you can say that ..but the battery is cheap & best for testing projects...
Nice bhai
Sap logo kit jo light on off remod se hai yah ghuthi hai game apna mobile number chahiye
Amigao faz adataptador bluetooth
Short lagne ka dar hoto....video q banaya Bhai....
shock nahi lagega aap sirf dc circuit pe kam karaahe ho...lekin accha relay use karna....
also remember 220v is very dangerous to work if you not suitable with 220v ac then pleaase don't do this...
Also if want to do that then do it at your own risk....
Bro .....I am a technician
Ohh. then it's ok...
very very nice awesom
Plz apna whatsapp no do mera circuit kaam nahi kar raha apse puchna hai..plz..plz
I am new in TH-cam....I also make a touch switch tutorial n many more videos....BT not have views....so plz help me
I don't have any idea bro...how to get more views..If I know that I will apply it on me....first....
Best of luck for your youtube journey
awesome
relay volt
12 or 6v or 9v
rela upload an IPS
Mhd👷👥👮👤👦🔧🔨🔩🏭🏠🚀🚨🔌🔋🔦🔬💣🔫🔪📱📢📣📡💻📹📷⚠💡😇👽👾👿💀💓
Nice
it's work properly
Good...
it's working
One light and one fan touch systam surkit
spdt ka volt
if you use 12v supply use 12v relay..or if you use 5v supply use 5v or 6v relay...the choice is yours...
nice
احسنت
saya suka
reply karo...i am intersted
Nice video w o f... Musick
valo ho6a
Auto run karta h ..MOSFET
big like :D
Hey it gives a shock...$
no..it is isolated circuit....
مشكور يتعذر الاشتراك .
AMZAD ALI
Mad ooo
Fen on. Of. Remote control banay Bina PCB ke
Nice vidio, suport back
i watched until that stupid song came on
Fake this not proper working ....
Very Nice
Very good
Very nice