1998 - 02 Honda Accord Acura 4 Cylinder Shift Solenoids A, B, and C
ฝัง
- เผยแพร่เมื่อ 3 ต.ค. 2024
- Attempting to Fix my 1998 Honda Accord Rough Shifting issue. Seems to be common with this Era of Hondas.
1-2 shift is my only issue now contemplating changing fluid soon.
![ผัวเถื่อน - ยูริ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/P08ORRVDGl8/mqdefault.jpg)
I had trouble with my 2003 accord (94,000mi) not shifting properly, thought it was solenoids .I noticed that there was no ground directly from battery negative to engine block, only to fender wells (crazy). I installed a heavy ground wire directly to engine block...no more shift problems. Now at 106,000 miles, still solid shifts.....Al Scott
Did changing the grounding actually work?
Check your rear motor mount. On high mile cB7/9 Accords, the rear motor mount often is cracked or dead and needs service. Ez to check: set up camera to record engine bay, start engine in Park, shift gear to Drive, shift back. If engine rotates with shift/load, the rear mount is shot. That adds a LOT of mass to any shift and makes it seems harsh. Replacing the mount is a beyotch! But wait! DIY: center engine, with a jack, inside mount, then fill bushing PARTIALLY with window sealant or poly. Be careful and patient. Good tips found by searching "bushing polyurethane diy" Don't fill completely! There must be flex on the motor mount unless you are high hp racing and can handle a LOT of vibration and reduced streetability and comfort. But solenoid cleaning is a good idea, too. All CB ATs in Accords have harsh shifting but the trannys last. Don't hammer the throttle off the line. Drive it like you're gonna give the car to your daughter for college. Hondas Rule!
I bought my 2002 at 140k with hard shift from 1st to 2nd. I cleaned all solenoids. It improved but still shift abruptly. So I changed 2nd oil pressure switch to new one. It did improve a lot. I just sold it a few months ago at 270k because cat got stolen it won't pass smog. Otherwise it still running til now.
Hi! Which one is presure switch? Is that the solinoid valve?
I have honda city 1997model. The issue was it has a jerk each time im going to put the shifter in reverse or in drive modes. And also i feel the jerking when it changing gears from low to high speed while running. Can i solve this by cleaning the filter or by changing the solinoid valve?
The 3rd gear is the problem on mine so i just waiting for my parts 3rd gear sensor switch , if not solve i might have to change the solenoid … great video btw
U got it fixed
Sometimes the problem is oil pressure switch. I changed my it fixed it.
I learned to change the fluid every year. It really helped keep the transmission functioning. It should have been recommended in owner's manual and that would have eliminated most problems.
Transmission fluid every year???
@@mhz1000aa For the price of Honda fluid ... you gotta be kidding!
4:15 that connection is a U type button press upwards so that button goes into the U with one finger and grab with other hand with two fingers and pull down and connection comes off, it can be fustrating. There's another solenoid rite under the battery, maybe that will help, the dual linear shift solenoid?
That's the torque converter lock-up, not the pressure solenoid. Just disconnecting and reading the code will confirm that.
My yr 2000 2.3 ulev-4 accord was not shifting well into gears, like something was clogged was the feeling i got, after 2 weeks of asking around, haynes mags, asking auto mechanics, and TH-cam videos i took off the double head solenoid but you gotta remove that 17 mm tranny screw to the left side, i got it off and it had gunk over the window screens, went and got the $11.99 mass air cleaner can at o Reilly's, cleaned it off with lint free rag then sprayed 3 little bursts of mass cleaner and hold it above your head so it drains and evaporates in the hot sun, i put it back in and wow it runs good now, i learned dont take off from around corners and stop signs because you put too much torque on the tranny, they are fragile trannys, now in gonna pull out the bottom single head solenoids and clean the window screens with mass flow, very important when you wipe the screen of dirt or dirty oil you only smear the gunky dirt across the tiny screens, you didn't clean it you smeared it, hold it upside down and blast 3 bursts of mass in the sun and it evaporates quick then pour 1/8 teaspoon of tranny on the screens and watch it drain through the tiny screens.
I did clean maybe off camera but my screens were not that clogged..
@@TinkeringTom91 my tranny is about 80 percent healthy but still has slight delay into 3rd gear, before it was running 40 percent, im eventually gonna have to decide to spend 3-4G's on a tranny or bail out, but my next car will be a timing chain Camry around 2010 and a freakin stick shift, no more auto trannys for me, i dont even like the little hesitation the way they shift even if its a new tranny, i been a stick guy all my life until i doped up and brought a used Honda accord auto.
I already changed a,b and c solenoids, it does keep kicking changes when i drive like an hour or some, when its cold it doesn't make it but after an hour the transmission starts kicking when i stop and want to accelerate again, P0740 i dont know what else to do
That's not your shift solenoid that's torque converter lock up.
Just got my little brothers 98 for free, on the drive home got a check engine light and turns out it was the dreaded p0740 and p1753, so I guess I need to run to the pull apart to check for one
How about late shift revers
My D4 light is flashing would this take care of that?
It should first off change oil & then clear codes if’It pop’s up again change your transmission fluid & clear the code,if that’s buy it then try the solenoid(Trans) & disconnect it & clean the gasket &screens if that doesn’t work try buying a new solenoid & install parts & you should be good after that I’d use Lucas transmission slip fix ❤❤❤❤❤
Mine was flashing other day it was as fuse
@@tommygunz341what fuse
Did you ever get the 1-2 shifting sorted out?
Just improved not totally fixed less harsh shifts.. I'm assuming at 270k and fluid never been changed there's some internal wear that won't just go away but can be band-aided for little while. I took out some fluid like a qt and put in some lucas atf conditioner.
@@TinkeringTom91 check rear motor mount for play.
@@doclockwood8809 that was my next move before I sold it
I got a problem whith my 98 honda civic lx it don’t wont to go on gear but it take reverse and when you turn it off and on it goes on shift and the go back on neatrual
Have a 96 db8 integra auto wont engage in gear war wont move wen accelerate help please
Mine doesn’t have the socket.. The yellow one is missing and still figuring it out where to top it. Lol
Yo Ajay quick question I need your help bro I’m having issue with slipping gear ⚙️ and there is a little kicking too and I use the scanner and I have these codes p0777 p1745 p1780 p0745 p0761 please help me and I just bought the car three months ago this is not honest mechanic bro they are lying They telling me need to rebuild transmission the car go on lil mode D flashlight bro 210.000 kilometre
Acura tl type s 2008 bro help me please
I have a 2000 honda accord lx with a code po780 will not shift from first to second gear d4 light is blinking any idea?
Not sure on that one haven't seen that scenario yet maybe someone else in the Comments. Thanks for watching!
DTC P0780 stands for “Shift Malfunction,” and this is triggered when the input and output speed sensors are unable to determine if the hydraulic pressure in the transmission matches the appropriate RPM and engine load.
I need to do mine, I’m think I need to clean my solenoids I might also do a fluid change ? Would you recommend a fluid change some people say not to do it
Depends on how long it's gone without service. If its way overdue and never serviced it may not be wise because it may do more harm than good when the New Fluid Starts to try and clean old fluid particles that have stuck to walls and will now be cleaned off and potentially clog tranny fluid passages.
replace with honda atf only. u may need to replace more frequent to clear out the stuff from previous fluid.
Mine is a honda city 1997 model. Automatic transmission.
The issue is it has jerking when i move the shifter from park to reverse and even on drive modes. And when it running, i can feel the jerks when it change gears from low to higher gear. Can i diy cleaning this valve and filter? And can i use gasoline to wash the filter? Hope ypu answer me. Thanks a lot. Watching from Philippines 🇵🇭
I suppose you could use gasoline as last resort careful with rubber seals. I replaced some my Sensors with a good slightly newer donor vehicle from Auto Junkyard.
suggest replacing the tranny fluid, use honda atf brand only.
I do hate these videos just get to the dam point 😂😂😂
7639
32879
09870
I have code p0730
Me too
Code p0730 is improper gear ratio. I got the same on my 01 honda crv, just two weeks ago, with a rebuilt transmission 16 months ago. I changed the fluid and will run it for a couple hundred miles before I change the lower shifting solenoid and flush the fluid again. Mine wasn't shifting in low gears so in the meantime I'm shifting it manually from 1 to 2 to D
Did you solve it already?
@@tonyr8443 what was the fix
Wď
Sorry Tom, your video was just too painful to watch.
How did this end? Was the fix successful?
It definitely Improved my situation. It drives better than before. I think there are other factors that make my Tranny rough shift... So for some people this may be all you need if you have kept up with Tranny fluid services and the Tranny does not have internal wear