How to scan OBD-II Codes on a 2007 Jeep Grand Cherokee
ฝัง
- เผยแพร่เมื่อ 9 ก.ย. 2024
- How to obtain the trouble codes from a 2007 Jeep Grand Cherokee without a scan tool. Note this procedure is pretty much the same for most OBD-II-equipped Chrysler, Dodge and Jeep products made after 1998. Use this procedure to help decide how to fix your vehicle, or as part of the process of deciding on a used vehicle purchase.
![ตีสิบเดย์ [FULL] | นางเอกหมอลำเงินล้าน "อุ๋งอิ๋ง เพชรบ้านแพง" & ไฮโซสาวสุดฮอต "ลิลลี่ เหงียน"](http://i.ytimg.com/vi/jPxQS_EgrJ4/mqdefault.jpg)
![[LIVE] : ONE ลุมพินี 78 | คู่เอก "ปกรณ์ vs ฟาบิโอ"](http://i.ytimg.com/vi/LSOmgl0Th2c/mqdefault.jpg)
This was very helpful. I use this method on my 2005 Jeep Grand Cherokee in the Limited trim with the V8. No scan tool needed to see if codes are available. The scan tool is needed to determine what the codes mean in detail, but not needed to find if codes are there in general.
Thanks this helped i tried following the instructions in some other user forums and couldnt get it. It was a matter of doing at a faster speed that I was able to pull the codes! Much appreciated!
Thanks for this video, I'm having start up problems so this should pin point where problem is, with out ££ fantastic ££ garage costs.
thanks bro! I found my code and diagnosed my problem...its only a leak so I can press on for a few more months :D
Thanks for the video. Worked on my 2010 jeep grand cherokee limited
Thanks man for the trick, it helped me a lot! On my 2006 Grand Cherokee, I've just got the check engine light on and almost panic... 🤣🤣🤣 The code I've got is P0128, which is probably only the thermostat valve not working properly.
Thanks Bro, I just got the oil changed yesterday. It was low when I checked it. It's no longer doing it now. Thanks for ur help.
thank you so much :)
When I tried this, it did not work for me, it just reads what it normally reads depending on what I have it set on. Any thoughts? Mine is a 2007 Rocky Mountain Edition with just shy of 98,000 miles and my engine light is what originally came on. Thank you.
Thank you I just called Firestone and they told me that it would take 2 hrs to run a diagnostic what a crock of crap. I will do this when I get home from work
Thanks for the video! Now I know how to check for codes myself. I have a 2005 Grand Cherokee. The Jeep's manual tells you how to check if the computer is ready, for say, an emissions test, however, it doesn't explain how to actually check the computer. Thanks for telling me and everyone else how to do this! (:
worked on my 2005 grand cherokee limeted have to keep key pushed in and do what video says
Thank you
BTW this process works for the 1999-2010 Grand Cherokees (:
Doesn’t work for my 06
Wow i did not know that. I used my code reader to detect the check engine light, but now i don't need it thanks.
This used to work on back in the 90's on my 1997 ZJ.
Works on 2005 Jeep Grand Cherokee. Just have to do it fast. It wouldn't work for me at first.
Thank youu
I have an 08, this little trick doesnt seem to work for this model. Did they disable this handy feature on the 08 model, or is there another technique that I dont know yet?!?!
Hi, this was helpful, I need help removing the "oil Change" indicator. (The oil can symbol) it only comes on when I stop the car at a red light or stop in traffic.
Hello there I'm doing what You said, but on My dash board it reads left trae dolor Open,, & there all closed, do You have any info on that??
This doesn’t work with WK’s equiped with diesel om642 engine
It doesn't work on my 2006 Laredo.
doesn’t work on my 5.7 2006 either FML
Same
We have a problem in our grand cherokee 2006 4x4, when we start the ligths, if we ligths on only the minimun ligths every things works ok, but when we swicth on the front lights, only starts the rigth one, if we start the hi-ligths only start one hi-ligths at left side, and one normal ligth(not a hi-ligth) at rigth side , meanwhile the wipers blades, the windows and the claxon doesn't work, and we hear a circuit noise inside of the place where is the multifunction swich. can you help?
it also works on the 04
do you know how to reset the ODB code?
hi does this model have the fuel usage gage ,the one that tell the ltrs used per ks it usualy there the compass is or do you program it vire the key many thanks
Sir please i need help my jeep when i do that procedure it says DONE but there is a problem with the engine when i drive it for five minutes the engine starts making cracking sounds when i gas it and some times shuts down. That problem makes difficult for the vehicle to move please help
hi and thanks for reply mine has the compass and temp and was wondering can it switch over to fuel lits to 100 ks milage
Great video. But this doesn't work in my (UK spec) 2006 WK 3.0 CRD.
I did it and show me p0507 code
After i turn the car on
The speakers are said ( you have problem with idle air) throttle body
Thank you
Dodge nitro 2008
Thanks a million :-)
Didn't work for my 2009 Grand Cherokee Laredo 4x4
does it work on 2006 grand cherokee too?
This doesn't work on mine. I have to use an OBD scanner that will connect to my iPad or iPhone.
It works for me with my 2005 Jeep Grand Cherokee in the Limited trim. Mine has the V8. When you turn the key 3 times you have to do it at medium speed. Not fast. Just medium speed. I use this method all the time to see if codes are available without the use of a scan tool.
Do you use a Scan tool and if so which one?
Geoff I have a 2008 Jeep Grand Cherokee Laredo and my airbag light is staying on. I tried your trick, but I could not get the process to work. 1. Should this work for my vehicle and 2. will it give me a code for why my airbag light is consistently on? Thanks for your video!
My air bag light on my 2009 Jeep grand Cherokee also stays on I believe it's the clock spring that needs to be replaced.
dan SEKERAK lots of timed airbag lights (sensors) go on due to fuses being taken out which are labeled .. "spares" and they are not . Happened to me.
I switch on three times but no scan report is given. What happened? My car is 2nd hand 2007 Grand cherokee larando sport 4*4
hua mei
It works for me with my 2005 Jeep Grand Cherokee in the Limited trim. Mine has the V8. When you turn the key 3 times you have to do it at medium speed. Not fast. Just medium speed. I use this method all the time to see if codes are available without the use of a scan tool.
MY dash goes crazy and then displays service electric brake system. Can anyone help me with this!!!!
Thanks!!!
Mine does this usually after the engine has been shut off and then restarted typically within 20 minutes and move off, the transmissions go tight and it gets wheel hop if im trying to turn, if I'm on the straight and try to move off it culls the engine power and I can hear the solenoids the the transfer case and axles making the similar noise to the switching to 4low.
My symptoms improved when I replaced a bad wheel bearing - it's also worth checking tread depths are with a 1mm or 2mm of each other.
It works for me with my 2005 Jeep Grand Cherokee in the Limited trim. Mine has the V8. When you turn the key 3 times you have to do it at medium speed. Not fast. Just medium speed. I use this method all the time to see if codes are available without the use of a scan tool. As for the service electric brake system message that means the ABS sensor is bad and needs to be changed. It's either the ABS sensor for the front left wheel or the front right wheel.
Nah!
Nothing, this tip does nothing on WH GC 2005 and 2007.
For a full listing of fault codes look here: www.wjjeeps.com/faultcodes.htm
For Dodge/Chrysler/Jeep-specific codes look here: www.obd-codes.com/trouble_codes/dodge/
It doesn't works in my WH 2005
NOT WORKING on a 2006 WK Laredo 3.7
It works for me with my 2005 Jeep Grand Cherokee in the Limited trim. Mine has the V8. When you turn the key 3 times you have to do it at medium speed. Not fast. Just medium speed. I use this method all the time to see if codes are available without the use of a scan tool.