You should not use brakleen to clean EGR tubing, the residue left behind from brakleen will cause soot to accumulate faster leading to repeat failures, carb cleaner is what most OEMs recommended.
I have seen a same comment on some other videos but not sure if its from you or someone els and its actually the opposite of that! The Carb cleaner and Brake cleaner have same exact ingredients except the brake cleaner has methanol which helps the liquid to evaporate fast and leave no residue behind. Carb cleaner does leave a bit of an oily residue behind. The only time i don't use brake cleaner is when the part has rubber or plastic because the methanol intends to swell those parts and they deteriorate after a while other than that always brake cleaner and never had any problems.
Hello I have a volvo d 13 2013 I have 2 codes spn 637 fmi 3 and spn 4752 fmi the problem in my truck is hard to start the engine eny of this codes influence to the engine start.
If I were you in your situation I would start by replacing the crankshaft position sensor and delta pressure sensor as it’s easy to do and not very expensive and hopefully that fixes the problem! After that I would take it to the mechanic as it might be the injectors. Good luck man
Yes I did as the sensor wasn’t recording the right amount of flow which caused the regen not being completed. I hope this helps, since I posted this video I didn’t have this issue again.
Hey i have a 2012 vnl. Its not doing anything when i try to crank it. Its giving me this message along with check engine light. J1939 communication error with engine ECU. Any idea what could it be?
Possibly turn off the battery switch then back on. Typically that error message is a ground issue. Clean all the battery terminals, clean the connecting bars, check the buss fuse on the large battery cable, check the fusible link large negative cable that attaches to the frame, check the ground connections at the pass thru on the firewall. You'll find some upper right drivers side and more below that area to the left. Check the connections at the starter. Clean them all with sandpaper and put it all back together and hopefully you should be good to go.
Hey man my truck is a 2012. It was running fine with check engine on. I went on vacation for a week and when I try to start it the lights would come on, but it won’t crank at all. The only message i get it Maintenance required vehicle Ecu. And j1939 Communication error with Engine ECU. Please help me out with this if you have any idea what could it be.
I am sorry to hear that. I never have experienced your issue in the past and I don’t want to give you any miss information! I would recommend you researching your code and see what info you can find. If I were you I would contact a shop and have them check it out if you can’t find any info about the code you getting. I am sorry I couldn’t be helpful and best of luck to you. Keep us updated please
Thanks for the video. Hopefully this helps me
Glad it helped! Best of luck
I’m so glad I run into your video 😅 definitely help me with my headache and wallet. Thank you.
Thank so much for doing this. I’m having the same issue and This video really helps 👍👍👏👏
Thanks Liri 🙌🙌🙌🙌🙌🙌
Good video, very Informative
I think you solved my problem thanks.
Thank you very much for this video
Than you for information it was helpful.
Having the same issue.... thank you
Thank you same problem.
Thanks
Good job!!
Good video
Nice video
Thank you
Brother, I got the same issues with these codes. I got spn 411 and 611 came up yesterday
What are the sensors called or I would like to service it ?
You should not use brakleen to clean EGR tubing, the residue left behind from brakleen will cause soot to accumulate faster leading to repeat failures, carb cleaner is what most OEMs recommended.
I have seen a same comment on some other videos but not sure if its from you or someone els and its actually the opposite of that! The Carb cleaner and Brake cleaner have same exact ingredients except the brake cleaner has methanol which helps the liquid to evaporate fast and leave no residue behind. Carb cleaner does leave a bit of an oily residue behind. The only time i don't use brake cleaner is when the part has rubber or plastic because the methanol intends to swell those parts and they deteriorate after a while other than that always brake cleaner and never had any problems.
Thank you…!
Having same problem right now
Hopefully you get the issue solved. I didn’t have this problem again since I posted this video and hopefully it stays that way!
Good luck
Hello I have a volvo d 13 2013 I have 2 codes spn 637 fmi 3 and spn 4752 fmi the problem in my truck is hard to start the engine eny of this codes influence to the engine start.
If I were you in your situation I would start by replacing the crankshaft position sensor and delta pressure sensor as it’s easy to do and not very expensive and hopefully that fixes the problem! After that I would take it to the mechanic as it might be the injectors.
Good luck man
Hey buddy, did you have frequent regents also?!
Yes I did as the sensor wasn’t recording the right amount of flow which caused the regen not being completed.
I hope this helps, since I posted this video I didn’t have this issue again.
👍👍👍😀
Hey i have a 2012 vnl. Its not doing anything when i try to crank it. Its giving me this message along with check engine light. J1939 communication error with engine ECU. Any idea what could it be?
Possibly turn off the battery switch then back on. Typically that error message is a ground issue. Clean all the battery terminals, clean the connecting bars, check the buss fuse on the large battery cable, check the fusible link large negative cable that attaches to the frame, check the ground connections at the pass thru on the firewall. You'll find some upper right drivers side and more below that area to the left. Check the connections at the starter. Clean them all with sandpaper and put it all back together and hopefully you should be good to go.
Hi there I was having the same problem and by replacing with the new ignition switch the problem is gone. Easy and simple fix. ✌️✌️
Hey man my truck is a 2012. It was running fine with check engine on. I went on vacation for a week and when I try to start it the lights would come on, but it won’t crank at all. The only message i get it Maintenance required vehicle Ecu. And j1939 Communication error with Engine ECU. Please help me out with this if you have any idea what could it be.
I am sorry to hear that. I never have experienced your issue in the past and I don’t want to give you any miss information! I would recommend you researching your code and see what info you can find. If I were you I would contact a shop and have them check it out if you can’t find any info about the code you getting. I am sorry I couldn’t be helpful and best of luck to you.
Keep us updated please
@@lirives7660 thank you very much