Thanks for the videos, I drywalled and painted my dad's wood working shop this week. because of your videos I didn't do a shit job I actually did a really nice job. I really appreciate it.
You do pretty well. The biggest thing to remember is to set the depth gauge properly. If you drive the screws to deep, they will not properly hold the drywall. Practice makes perfect. Start slowing getting the screw going in level and straight. Do not try to go to fast at first. Get the rhythm and flow down. Put just a few screws in your off hand. As you run the screw into the wall flip the next screw between your fingers ready to go onto the tip with the other hand. Soon you will be doing two things at once. Start slow, speed comes with repetition and muscle memory. After a while you will know when the screw missed or is not right just by the sound and the feel.
I AGREE WITH YOU SHAWN. I NEED TO SET MY GAUGE AND GO SLOW TO AVOID PASSING THE FLUSH MARK. NEVER HUNG DRY WALL BEFORE. SO FOR ME SLOW & EASY & RIGHT DOES IT. CAN ONE LOOK AT A PROPERLY SUNK SCREW & TELL WHETHER IT WAS PLACED FAST OR SLOW?! I WILL HAVE SOME MOMENTUM IN BEGINNER MODE. ALSO SOME MOMENTUM IS IMPORTANT WITH ALL THE PHYSIC FACTORS INVOLVED. ANYWAY IT IS DOABLE FOR ME & IMA KNOW MY WALLS HAVE BEEN HUNG RIGHT WITH ALL THE TIME & ATTENTION MY LIVING QUARTERS.... LAIR IF YOU WILL DESERVES... HAVE THE BLESSED DAY EVERYONE EVERYONE IN JESUS' NAME AMEN🙏🏽👸🏽🙏🏽
@@ROMANS.CHAPTER8.38-39 No on the fast or slow. Straight and level going in the most important. Not being too close to the edge is second. If you think a screw crushed the edge. Put one in a few inches above and below it.
@@ROMANS.CHAPTER8.38-39 one of things you dont want is them not to be seated enough. Happens more often with screws going in at an angle. One edge will stand proud of the surface. Before getting using the sheetrock mud. Run the taping knife over the seams and the screw heads. If you hear a clicking noise that screw is proud and it needs to be screwed in just a bit more. You will find them with the taping knife, when you start running the mud.
@@shawnr771 YEP! SAW THAT ONE IN A FEW VIDEOS.... STILL IN THE RESEARCH/ IN-SERVICE MODE.... THANKS SO VERY MUCH SHAWN.... KNOWLEDGE IS POWER... IT'S THE LITTLE THINGS THAT MAKE THE BIG DIFFERENCE. 🙏🏽🏡🙏🏽
Best advice i could ever give, wear a glove on the hand holding the screws.... Don't if you rather remove the screw's shrapnel in your fingers after a 500-1000 screw run.
I have a lot of tool, but sadly there isn’t that much work in Houston Tx, right now, but I hope we will pass this and it will be better for us the “business starting” Thank you for your videos 👍🏻🙏🏻
correct method, unless you are using G Screws aka hi low, aka board to board screws... then you want to start off at low rpm at a slight angle, then increase the rpm and straighten it out towards the end
Minor peeve ( which has nothing to do with your awesome channel) Every time I watch one of your videos, TH-cam will recommend pretty much the entire catalog of videos from the 70's band The Carpenters. You're worth it however!
Another great, and hilarious video. Ben can you do a video/review on some of the autofeed/strip feed type guns? About to rehang 1200 sqft of ceilings in my house and your opinion on the different models available would be invaluable. You are a true pro.
IMHO, not that it means anything, if your a homeowner/DIY'er, get the Metabo or Senco for $150 or less. If your a pro get the Dewalt cordless with the $75 autofeed adapter.
@@chriswithrow3107 Comes down to frequency of use i think. If it's only going to be brought out and used on a few jobs every once and a while then why spend the money. $140 or under and done. I like the Senco for inexpensive corded one, not everyday use. I think they all do a good job (ive used the Senco, Dewalt, Hilti, Rigid and Makita on different jobs). If you've bought into a battery/tool system then its a easier call. I'm using the Dewalt Max20v so it was a no brainer that when it came time to buy a new drywall gun i'd get the cordless ($140 tool only) so I could get the collated screw attachment ($80). Then you're looking at $220. More if you need a battery and charger. Not many complain about the Dewalt system, gets rave reviews and it really does work well. I like the versatility of using the gun with or with out the attachment. The attachment easily pops off to fix any screw that may go in sideways or weird. So thats why I choose it. The gun has a brushless motor and has great power too which I think is critical. Better for long use and abuse. Hope that explains it better. Which do you use or are leaning towards getting?
@@jeffreyklaum13 I am vastly invested in Dewalt 20&60v, (electrician) and I know I'm gonna want a cordless gun. Just looking for the one that performs the best, if it's red or green or orange or yellow.
@@chriswithrow3107 Then for sure get the Dewalt and buy the attachment if your have the batteries. Really is one of the best I've used. Dewalt knocked it outta the park with this one. Im a GC so I get involved with a vast array of projects. Its definitely one of my favorite tools.
Good video Ben, Screw gun is on my wish list. Future vid will you show us some tips and tricks on making sure the framing is strait before hanging? You’ve shown us how to mud frame ( and I’ve since used ), but would love to see how you straiten studs, shim, and hang ceiling board over hanger brackets ( ie. where joists change directions for cantilevers etc)
I agree. I know how to use shims but it would be really helpful to have a sequence of things to check to make sure the framing is ready for drywall. I find that I miss a lot of framing problems until it's covered in drywall, then it's really obvious but too late to fix anything.
strongly suggest you use #2 grabber bits there the best I am a professional boarder in the lower mainland and can screw off a 8' sheet in less than 20 seconds
Hahaha, ohhhh crap I'm old, because missing that stud after it was marked, like I've been doing all this week in my basement, was the funniest thing I've seen in months.
My house is old and has rough cut lumber which is super hard. I would never be able to do that. The last time I hung any drywall on my wall; I had to predrill every hole or the screws would break off. Guess I can use my dry wall gun everywhere else.
I do too, i'm suprised not so many guy's use one. When doing drywall you put it on the arm holding the drill. (I usually do the oposite for driving nails for obvious reasons.
You're pretty good humored when you make a mistake, it reminds me a little of Julia Child. Julia Child used to make an occasional mistake in her live episodes, she'd recover gracefully by admitting the mistake and that she's glad it happened because it's an opportunity to teach - then she'd continue by showing the audience what went wrong, why, and how to fix it.
Drill- Packedge in typical box, came with a tool bag (added bonus), two batteries, one charger, drill, and driver. Two words "plenty of Torque" th-cam.com/users/postUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv well I guess that's three. Nice upgrade from current setup. Has belt clips, I don't think I will be using those. Driver and drill were bigger than what I expected but it is an upgrade from the current setup. For the money I would say that this is a great setup for Professionals and DIY/Weekend warriors.
@@tabascocrimson7865 got plenty batterys. But for the drywall guns i use the 2 amps. Cheepest battery out. Lightest on the gun. Usually last till around lunch.
HAHAHAHAHAHAHAHAHAHA love the "i'll probably mess up cause i'm filming" it happens all the time. you are correct on fastest guns, i've seen guys at lightning speed. was surprised to see "drywall screw inspection" from an actual inspector, he called out the spacing out, that happend at a job where they didn't hire experienced laborers. i learned many things from being at my first hospital job, and the construction out from Texas had to learn California rules... then the guys hanging ceiling didn't use earthquake "chin-ga-deras" i forgot the names clips of some kind. edit: forgot reason i came here. i've used the speed saw to cut holes or to make cuts using speed saw and the special drill bit. is there one for plaster ? little trick i learned from the guys was, if you break your bit, use a drywall screw and it will work and get you out of a jam. tried it and it does, but bit is faster and easier to use
Hello sir Nice can this makita as it is screwing through the plasterboard does it have the power to pierce through the aluminum profile as well at the same time in one sweep motion?
Cordless tools dont have the same kick as corded tools. If you need to work all day long, its corded all the way. Cordless tools are more suited for smaller projects, reparation, or when there is no access to electricity
What do you do if the screw is only a degree or so off 90 so when it is screwed in part of it is below the surface and part of the screw head is above?
Question: Does the bit engage the screw as you're loading it, or is it magnetically held until you actually go to drive it? If the former, couldn't you sometimes have the threads nick your fingers while loading?
Here in Australia, watching the boys putting up plasterboards in my house, they used glue to and very few screws. i asked them why and they said, “that’s how it is, the glue is what keeps the plasterboards stay put, the screws are there just to keep them boards there while glue dries”. What are the pros and cons of using this method?
You had problems because you changed to a black shirt instead of your lucky white lol. I have used a gun just like that for years and just recently learned you can pull the nose cone off to back out screws that have been over driven or missed a stud.
I’m about to be fresh out of highschool and thinking about going into the union for carpentry. Do you think it’s a good idea? And also is there different types of carpenters because I see you working in homes and others in bigger buildings
I am a General Contractor, 29 years old, joining the Carpenters union now. When I was your age I thought myself above it, and started my own construction company. I've got a family now and I am a bit ashamed I didn't join the Carpenters union then. Go for it, it will change your life for the better.
lol, showing your mistakes and laughing at yourself makes this channel so much better than others
exactly
LOL, thanks for leaving that in the video for us to have a laugh.
"So this is how you screw up drywall." Yeah, well, I already know how to screw up drywall. Now I know how to do it correctly. Thanks.
😂🤣😂
Me too
Thanks for the videos, I drywalled and painted my dad's wood working shop this week. because of your videos I didn't do a shit job I actually did a really nice job. I really appreciate it.
You do pretty well.
The biggest thing to remember is to set the depth gauge properly. If you drive the screws to deep, they will not properly hold the drywall.
Practice makes perfect. Start slowing getting the screw going in level and straight. Do not try to go to fast at first. Get the rhythm and flow down.
Put just a few screws in your off hand.
As you run the screw into the wall flip the next screw between your fingers ready to go onto the tip with the other hand. Soon you will be doing two things at once.
Start slow, speed comes with repetition and muscle memory.
After a while you will know when the screw missed or is not right just by the sound and the feel.
I AGREE WITH YOU SHAWN.
I NEED TO SET MY GAUGE AND GO SLOW TO AVOID PASSING THE FLUSH MARK. NEVER HUNG DRY WALL BEFORE. SO FOR ME SLOW & EASY & RIGHT DOES IT. CAN ONE LOOK AT A PROPERLY SUNK SCREW & TELL WHETHER IT WAS PLACED FAST OR SLOW?! I WILL HAVE SOME MOMENTUM IN BEGINNER MODE. ALSO SOME MOMENTUM IS IMPORTANT WITH ALL THE PHYSIC FACTORS INVOLVED. ANYWAY IT IS DOABLE FOR ME & IMA KNOW MY WALLS HAVE BEEN HUNG RIGHT WITH ALL THE TIME & ATTENTION MY LIVING QUARTERS.... LAIR IF YOU WILL DESERVES... HAVE THE BLESSED DAY EVERYONE EVERYONE IN JESUS' NAME AMEN🙏🏽👸🏽🙏🏽
@@ROMANS.CHAPTER8.38-39 No on the fast or slow.
Straight and level going in the most important.
Not being too close to the edge is second.
If you think a screw crushed the edge.
Put one in a few inches above and below it.
@@shawnr771 THANKS SO VERY MUCH SHAWN
🙏🏽😇🙏🏽
@@ROMANS.CHAPTER8.38-39 one of things you dont want is them not to be seated enough.
Happens more often with screws going in at an angle.
One edge will stand proud of the surface.
Before getting using the sheetrock mud.
Run the taping knife over the seams and the screw heads.
If you hear a clicking noise that screw is proud and it needs to be screwed in just a bit more.
You will find them with the taping knife, when you start running the mud.
@@shawnr771 YEP! SAW THAT ONE IN A FEW VIDEOS.... STILL IN THE RESEARCH/ IN-SERVICE MODE.... THANKS SO VERY MUCH SHAWN.... KNOWLEDGE IS POWER... IT'S THE LITTLE THINGS THAT MAKE THE BIG DIFFERENCE.
🙏🏽🏡🙏🏽
Wait a minute . . . did I just see a craftsman with a sense of humor? Thank you. I will subscribe and learn more from you.
Thanks, I learned something! I’ve owned a Milwaukee drywall for 3 years and I was using it like an idiot.
I can't believe that dude left his messup in the video. Big props
I love how you left the bloopers in. I was cracking up. 😂
1:46 That's how I do it.
don't try that at home lol
Give this guy a high mark just for making us laugh and laughing at himsef!
Best advice i could ever give, wear a glove on the hand holding the screws.... Don't if you rather remove the screw's shrapnel in your fingers after a 500-1000 screw run.
Oh God I hate drywall screws because of that. Dang metal shards are hell!
Best laugh I had all day! Lol. And thank you for the information too.
I have a lot of tool, but sadly there isn’t that much work in Houston Tx, right now, but I hope we will pass this and it will be better for us the “business starting”
Thank you for your videos 👍🏻🙏🏻
You are a legend
Oh that was just awesome. Thanks for brightening my day
I had me a good laugh @ 1:48 😂
correct method, unless you are using G Screws aka hi low, aka board to board screws... then you want to start off at low rpm at a slight angle, then increase the rpm and straighten it out towards the end
I learnt from you couple of tips, thanks a lot
Vancouver carpenter, I really appreciate the way you showed because I had some issue @ construction school with it.
Holy shit this guy has two different lives love your skating
Thanks I learned something!!
lmao, attempt 1 had me laughing sooo hard I had to pause and let it work its course.
Hahahaha...I LOVE the screw up. ~~SUBBED~~ because you kept it real. Thank you.
Minor peeve ( which has nothing to do with your awesome channel) Every time I watch one of your videos, TH-cam will recommend pretty much the entire catalog of videos from the 70's band The Carpenters. You're worth it however!
The battery drills are nice but the corded ones fit right in the corners easy
Another great, and hilarious video. Ben can you do a video/review on some of the autofeed/strip feed type guns? About to rehang 1200 sqft of ceilings in my house and your opinion on the different models available would be invaluable. You are a true pro.
IMHO, not that it means anything, if your a homeowner/DIY'er, get the Metabo or Senco for $150 or less. If your a pro get the Dewalt cordless with the $75 autofeed adapter.
@@jeffreyklaum13 Can you elaborate?
@@chriswithrow3107 Comes down to frequency of use i think. If it's only going to be brought out and used on a few jobs every once and a while then why spend the money. $140 or under and done. I like the Senco for inexpensive corded one, not everyday use. I think they all do a good job (ive used the Senco, Dewalt, Hilti, Rigid and Makita on different jobs). If you've bought into a battery/tool system then its a easier call. I'm using the Dewalt Max20v so it was a no brainer that when it came time to buy a new drywall gun i'd get the cordless ($140 tool only) so I could get the collated screw attachment ($80). Then you're looking at $220. More if you need a battery and charger.
Not many complain about the Dewalt system, gets rave reviews and it really does work well. I like the versatility of using the gun with or with out the attachment. The attachment easily pops off to fix any screw that may go in sideways or weird. So thats why I choose it. The gun has a brushless motor and has great power too which I think is critical. Better for long use and abuse.
Hope that explains it better. Which do you use or are leaning towards getting?
@@jeffreyklaum13 I am vastly invested in Dewalt 20&60v, (electrician) and I know I'm gonna want a cordless gun. Just looking for the one that performs the best, if it's red or green or orange or yellow.
@@chriswithrow3107 Then for sure get the Dewalt and buy the attachment if your have the batteries. Really is one of the best I've used. Dewalt knocked it outta the park with this one. Im a GC so I get involved with a vast array of projects. Its definitely one of my favorite tools.
Good and useful tips, thank you
Good video Ben, Screw gun is on my wish list. Future vid will you show us some tips and tricks on making sure the framing is strait before hanging? You’ve shown us how to mud frame ( and I’ve since used ), but would love to see how you straiten studs, shim, and hang ceiling board over hanger brackets ( ie. where joists change directions for cantilevers etc)
I agree. I know how to use shims but it would be really helpful to have a sequence of things to check to make sure the framing is ready for drywall. I find that I miss a lot of framing problems until it's covered in drywall, then it's really obvious but too late to fix anything.
Thanks Ben. Interesting tool!
Assuming this doesn’t work for installing gypsum to resilient channel - just to studs/OSB?
LOL! Sideways into the wall.. absolutely amazing! Haha
Total classic, I don't even see new guys mess up that bad.. hahaha :D
I bought the same Makita drill.. i found the bit was shite ... Replaced it and it went much better
strongly suggest you use #2 grabber bits there the best I am a professional boarder in the lower mainland and can screw off a 8' sheet in less than 20 seconds
HEY MAN Awesome video .What is the reason this guns have depth adjusmet and its not fix in the right depth?
Thanks for this, saving me a lot of time!
Thanks for the video. I gave me a laugh❤️🤣
Hahaha, ohhhh crap I'm old, because missing that stud after it was marked, like I've been doing all this week in my basement, was the funniest thing I've seen in months.
Hahahahaha dude you called it!!! First screw NOPE 😎awesome video
My house is old and has rough cut lumber which is super hard. I would never be able to do that. The last time I hung any drywall on my wall; I had to predrill every hole or the screws would break off. Guess I can use my dry wall gun everywhere else.
Great video, thanks. Don't most pros use an autofeed?
Yes
This is a great video have you seen the cordless Hilty guns with the screw clips
Lol I love the realness of that mess up imbedding the screw sideways into the wall 😂😂😂😂😂
Every city needs a VANCOUVER CARPENTER
Lol...awesome. Thanks for leaving the goof in. But for me....collated for the win.
Never seen one of those before. I probably couldn't justify getting one but nice to know....
My significant other makes that sound after every pump, now I know why
mad respect for this guys skill and sharing it. At the same time that screw going sideways was hilarious, how?!
you're really screwing up bro. lol. great content
That really cracked me up!
I like to use a magnet wristband
I do too, i'm suprised not so many guy's use one. When doing drywall you put it on the arm holding the drill. (I usually do the oposite for driving nails for obvious reasons.
Ben, please do a video on how to grab a handful of screws out of the box without getting poked. Thanks 😁
You just need to shake it up a little so they aren't so compact.
@@vancouvercarpenter lol I thought getting poked was unavoidable but that makes a lot of sense 👍
You're pretty good humored when you make a mistake, it reminds me a little of Julia Child.
Julia Child used to make an occasional mistake in her live episodes, she'd recover gracefully by admitting the mistake and that she's glad it happened because it's an opportunity to teach - then she'd continue by showing the audience what went wrong, why, and how to fix it.
Drill- Packedge in typical box, came with a tool bag (added bonus), two batteries, one charger, drill, and driver. Two words "plenty of Torque" th-cam.com/users/postUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv well I guess that's three. Nice upgrade from current setup. Has belt clips, I don't think I will be using those. Driver and drill were bigger than what I expected but it is an upgrade from the current setup. For the money I would say that this is a great setup for Professionals and DIY/Weekend warriors.
It's time to go cordless, my friend!
And get 2k worth of battery packs
@@tabascocrimson7865 got plenty batterys. But for the drywall guns i use the 2 amps. Cheepest battery out. Lightest on the gun. Usually last till around lunch.
And collated. Got one a while back, well worth the price of collated screws.
Yes that same Makita in cordless is awesome
I would never know how to use the gun, thank you for entertaining video
What do you do with screw that dosent hit stud
Can you put clutches on that gun?
I love you man your so great lol I’m going to mess this 2 in up and first try bam 💥
HAHAHAHAHAHAHAHAHAHA love the "i'll probably mess up cause i'm filming" it happens all the time. you are correct on fastest guns, i've seen guys at lightning speed. was surprised to see "drywall screw inspection" from an actual inspector, he called out the spacing out, that happend at a job where they didn't hire experienced laborers. i learned many things from being at my first hospital job, and the construction out from Texas had to learn California rules... then the guys hanging ceiling didn't use earthquake "chin-ga-deras" i forgot the names clips of some kind.
edit: forgot reason i came here. i've used the speed saw to cut holes or to make cuts using speed saw and the special drill bit. is there one for plaster ? little trick i learned from the guys was, if you break your bit, use a drywall screw and it will work and get you out of a jam. tried it and it does, but bit is faster and easier to use
Funny lesson but lesson taken. Thank you. *~.~
Good tips
How are you putting the screw onto the bit while its still running?
The clutch in the drill only engages when you apply pressure into the wall. It's the main difference between a drywall and regular screw gun.
"Good recovery, Mav"
Hello sir Nice can this makita as it is screwing through the plasterboard does it have the power to pierce through the aluminum profile as well at the same time in one sweep motion?
So that we don't have to drill the aluminum profile and then search for holes to screw afterwards
What is the purpose of holding the drywall gun at the motor, instead of pistol grip?
Puts your pressure directly on the drive instead of below it.
Lol. You can always blame it on the screw 😂👍
What bit is in the drill?
"So that's how you screw up drywall."
It's ok....we know what you mean!
That shit happen to me when I tried to show how bad ass my cordless drywall drill is 🤦♂️😭🤣 that's what I get for showing off
I always screw up on inside corners.
Why is there like a 1” gap at your wall to ceiling angle at 3:20?
Bad drywallers.
Thanks!
I am just trying to put my curtin rod up🤣🤣🤣
He may not be the best at screwing in drywall, but he has nice hair.
Some contractors are double screwing ceiling drywall? Do you think it is necessary?
Dude. Upgrade to the cordless Makita.
The motor doesn't run when the trigger is locked. Only when you depress the tip. 1000x better.
Cordless tools dont have the same kick as corded tools. If you need to work all day long, its corded all the way. Cordless tools are more suited for smaller projects, reparation, or when there is no access to electricity
GOOD TIMES, RUSTY ... 😂
Best part of your videos is when you mess up
Hello. It is used to perforate the metal profiles for the dry wall plates? Thank you.
Will this work the same with cement boards?
Never even knew there was such a thing as a drywall drill. I just have a regular cordless drill.
Thanks
What do you do if the screw is only a degree or so off 90 so when it is screwed in part of it is below the surface and part of the screw head is above?
Nailed it
Question: Does the bit engage the screw as you're loading it, or is it magnetically held until you actually go to drive it? If the former, couldn't you sometimes have the threads nick your fingers while loading?
SoSpiffy the bit holder and bit don’t spin till it is pushed against and when you reach the set depth it disengages
Exactly what I was thinking. Thank you for asking!
Very misleading title 😂
Self feed attachment is how to use it properly.
Wheres your belt fed screw gun? Makes the job alot quicker and its cordless and faster than any other way
Ah the memories! LOL
hmm, which one was the 'right' way again? :):):)
Here in Australia, watching the boys putting up plasterboards in my house, they used glue to and very few screws. i asked them why and they said, “that’s how it is, the glue is what keeps the plasterboards stay put, the screws are there just to keep them boards there while glue dries”. What are the pros and cons of using this method?
You got ripped off bro, shit will be on the floor in 5 years
Holy u heard of cordless
How to remove a bit
First thing on how not to do it: Do not wear safety goggles lol
How much...
You are like my boss says don’t do it like this do it how I show you and does it wrong messes up and says now you can finish it off
You had problems because you changed to a black shirt instead of your lucky white lol. I have used a gun just like that for years and just recently learned you can pull the nose cone off to back out screws that have been over driven or missed a stud.
I’m about to be fresh out of highschool and thinking about going into the union for carpentry. Do you think it’s a good idea? And also is there different types of carpenters because I see you working in homes and others in bigger buildings
I am a General Contractor, 29 years old, joining the Carpenters union now. When I was your age I thought myself above it, and started my own construction company. I've got a family now and I am a bit ashamed I didn't join the Carpenters union then. Go for it, it will change your life for the better.
I clicked faster than the drill