ABB Positioner Auto Calibration in English
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2021
- 🔥ABB Positioner Auto Calibration in English
🔥I have Tried to show you how to Auto Calibrate ABB Positioner through this Video. Hopefully after Watching the full video you will Understand about the auto Calibration of ABB Positioner. And you will have a good idea about it. Which can come in handy in the Future. And if you have any Problem Understanding after Watching the video, Please let us know in the Comments.
🔥ABB Positioner Auto Calibration in Hindi
• ABB Positioner Auto Ca...
🔥এবিবি পজিশনার কিভাবে অটো ক্যালিব্রেশন করতে হয়, সেটা আমি আপনাদেরকে এই ভিডিওর মাধ্যমে দেখানোর চেষ্টা করেছি। আশা করি ভিডিওটা সম্পূর্ণ দেখলে এবিবি পজিশনাল এর ক্যালিব্রেশন সম্পর্কে আপনারা বুঝতে পারবেন। এবং এটা সম্পর্কে আপনারা আপনাদের ভালো ভালো ধারণা চলে আসবে যেটা ভবিষ্যতে আপনাদের অনেক উপকারে আসতে পারে। আর ভিডিওটি দেখার পরে আপনাদের বুঝতে যদি কোন সমস্যা হয়, অনুগ্রহ করে কমেন্টে জানাবেন।
🔥 Please Subscribe My TH-cam Channel.
🔥TH-cam Link👇👇👇
/ @instrumentsolutions
🔥Massenger Link 👇👇
m.me/rahin.ahmed.31
🔥ধন্যবাদ।।। Thank You 😊😊
Tnx brother
nice. our control valve is -14% at 20mA and 100% in 4mA, rotary type? can we do your procedure
Thank you
Welcome 🤗
Very nice; good luck for you teacher.
Thank you so much 😊
Sooper videos
WHILE CALIBRATNG THE VALVE AUTO 34 RUN ME STRUCK HO RAHA HI. WHAT TO DO.
Hi sir from brazil !! I have some positioner TZIDC 110 ABB PA in OOS mode ( out of service ) so don't turning on (AUTO MODE) to bus comunication.
We tried to reset factory and basic reset them , but still out of service continuos.
You know something about its ploblem on device ?
Thanks for help!
bro, if the control valve characteristic is equal percentage. Do i need to change in the configuration?. then calibrate?
hi iam asking about cylinder control valve is it possible to fix the same ABB positioner
Gᴏᴏᴏᴅ ᴍᴏʀɴɪɴɢ sɪʀ 👍 ᴡᴏᴡ ɴɪᴄᴇ ɪɴғᴏʀᴍᴀᴛɪᴏɴ ❤️
Good Morning 🌄
Thank You
Bro make is Abb ok fine, but pls confirm the model
Thanks for this
Welcome 🤗😁
What if valve is hunting or overshoot during stroking which parameter will need to be adjust
If the valve is hunting, there is no option to adjust from parameters.
When hunting the valve, you have to adjust the volume booster. If you have any air leaks in your valve. And if there is a problem during calibration, the valve can hunt.
Bro. I have a doubt in DP type flow txmtr FF type. In txmtr Bar graph shows inproperly. Ie, in 0% pv bar graph shows 50%, how can solve this issue.
Please send me picture
tuhinbd712@gmail.com
I sent to your mail id, plz check
I am sincerely sorry sir for taking a little time.
Actually, I did some document analysis. But last 4 years, I have not had such a problem. I think you can recalibrate again.
And if not, then you can talk to a TA or Vendor.
sir Field to DCS wiring kaise karte hain batao control valve FT PT LT motorised valve rotameter
Wait for my next video. Hope to see a lot more.
Neutral position is not 0 ?
No subtitle brother
hi bro, can you do this in Russian language?
Where are you from?
I am from Kazakhstan, please tell what are you doing in this video after autocalibration, why do you set min and max position manually?
is it not enough to do autocalibration?
See After setting the minimum and maximum range, then valve will not have any problem when it is open or closed. And if you do not set minimum maximum range, then valve may be much more open when it is open. In a word, it can be set for safety of valve.
Good but
But?