First of all , you don't just keep the wires connected with your hands, you need a proper connectors. Second you need a minimum 4S battery. The 3S voltage is too low for this motor to operate. I don't see anything wrong other than that. Motors are working as it should at the voltage you provided.
Connect it properly before saying it doesn't work. How can you expect adequate current to flow through skinny wires loosely inserted in fat connectors? They're barely touching if at all.
I got this running well on a 2S setup using 2 LiFePo4 cells or about 6.6 volts. I use the same green motor, and a cheap 30A ESC. I believe Anh Khoa Ngo Nguyen has something defective here.
You seem to know very little about brushless motors. You have been swapping the motors with out disconnecting the power. Did you not notice when you connected the power for the first time the little tune the motor and ESC played, that is the motor test to set up the ESC to that motor. You NEED to disconnect the power each time you swap a motor.
Im planning to build 2 brushless motor using similar to what he posted. CW and CCW. Do i need to have 2 sets of ESC and 2 Speed dial or i can use 1 set of both only. Plese give some tips... using it for my kayak.
Hi. Im planning to build 2 brushless motor 1 clockwise and 1 counter. Do i need to 40 amp ESC and 2 speed controller or i can use 1 ESC and 1 controller?
I would like to buy this motor too, but you have a small battery, 12v 2.2A,the maximum absorption allowed for this motor indicates 24v 17a this motor to have good power I think you need to use a battery that provides 24v 15A therefore roughly 15 times more powerful
this guy doesn't speak english (NOT A JOKE) he speaks a language with weird accents that chrome can't translate, because he replied to some comments that were in this language but none of those who were in english
First of all , you don't just keep the wires connected with your hands, you need a proper connectors. Second you need a minimum 4S battery. The 3S voltage is too low for this motor to operate. I don't see anything wrong other than that. Motors are working as it should at the voltage you provided.
Connect it properly before saying it doesn't work. How can you expect adequate current to flow through skinny wires loosely inserted in fat connectors?
They're barely touching if at all.
May I ask you the 3d design?
I got this running well on a 2S setup using 2 LiFePo4 cells or about 6.6 volts. I use the same green motor, and a cheap 30A ESC. I believe Anh Khoa Ngo Nguyen has something defective here.
Did u make them work?
Or is it hardware issue?
You seem to know very little about brushless motors. You have been swapping the motors with out disconnecting the power. Did you not notice when you connected the power for the first time the little tune the motor and ESC played, that is the motor test to set up the ESC to that motor. You NEED to disconnect the power each time you swap a motor.
Im planning to build 2 brushless motor using similar to what he posted. CW and CCW. Do i need to have 2 sets of ESC and 2 Speed dial or i can use 1 set of both only. Plese give some tips... using it for my kayak.
@@mr.mister7489 best to have an ESC for each motor but they both can be controlled by the same speed reference controller.
Thank you
@@seanocallaghan5630 can you program the CW motor to CCW using a hardware program card or swapping the motor wires?
Very heavy means good magnets yes ?
motor này giá bao nhiêu vậy. khoẻ hơn motor thuyền 12v ko nhỉ
Hi. Im planning to build 2 brushless motor 1 clockwise and 1 counter. Do i need to 40 amp ESC and 2 speed controller or i can use 1 ESC and 1 controller?
1 controller per motor, match the Amp rating
@@CryingNeutrons thank you
@@CryingNeutrons can you program the CW motor to CCW using a hardware program card or swapping the motor wires?
They dont have enough current to start, thats what the second motor sound means check your ESC current output and the motors nomial current input
A chạy 2 motor cho mô hình hay 1 thôi thế, e đang gặp vấn đề vì 2 motor sẽ có sai số động cơ, làm cho k đi thẳng được với cùng xung
Mình chạy 2 cái. Cũng gặp vấn đề giống bạn. Nếu tự lập trình thì cần phải có thêm sensors gyro. Dự vào hướng mà điều tốc động cơ.
Why is the motor jammed?
Hi, is there 9v battery can work for this motor?
How to reduce rpm?
I would like to buy this motor too, but you have a small battery, 12v 2.2A,the maximum absorption allowed for this motor indicates 24v 17a this motor to have good power I think you need to use a battery that provides 24v 15A therefore roughly 15 times more powerful
That Will be 300w so... For how long can run?
And never stop your motors manually that generates a constante high current that can damage the entire circuit
If I don't want a controller, Can I connect the battery directly to the motor?
no its needs a ESC controller
What's the update for your project?, where did you buy this motor
thí motor, i guess on Amazon, brushless dc motor underwater 24V
Try six 3.7 volt battery u need to exercise rhe thruster
this guy doesn't speak english (NOT A JOKE) he speaks a language with weird accents that chrome can't translate, because he replied to some comments that were in this language but none of those who were in english
These need to run on 24 V
I bought the same found magnets rub on the is side two of the six I bought are junk not very good at all
I buy this brushless motor for underwater but it didnt work someone can help i will the video
One tuner can only drive one motor
cara masang di kapal gimana bg
gimana cara kalibrasi nya
called everything wrong that's all
those chinese engines are piece of shit.
only cheap tho !