Thanks for the video, Abdel. My 98 4runner is giving me a hard time. It started hesitating when accelerating months ago, but it slowly got worse. Now it hesitates and surges when sitting on traffic lights, and it doesn't want to go when I give it gas. Its almost like the engine is starving for gas. I have no vacuum leaks whatsoever. Do I have to take off the fuel rail to replace all 4 fuel injectors or can I do the same procedure you are doing? Mine is 2.7, but they are identical.
Hello Bryan, did you check to see whats the fuel pressure is on your truck? Also do you smell gas when you first start it? Also did you check for codes?
@@abdelcarfix2770 I have a misfire in cylinder number 1 when I checked using my scanner. The fuel pressure is good, I took the truck to a mechanic about a month ago and he checked that. Tomorrow I plan on buying a 140 dollar fuel injector to see if that one cylinder gets better. If it does, I would just change all of them. What are your thoughts? The engine is stable when Idling in my driveway, but when I drive it its a different story. Yesterday was the last time I drove it. I had to put it in park in every red light so it would stop shaking. It was pretty embarrassing to say the least. The fuel filter is new, the O2 sensors are new, the spark plugs I bought about 5 months ago, ignition coils are new as well, etc. Thanks for your response :)
I have a 2001 Tacoma 2.4l shakes when I start it sometimes and will idle rough . I got a code p0301 , cylinder one misfire ; check engine light was flashing . I replaced spark plugs,ignition coils ,mas sensor less than 5 months ago . I haven’t replaced any of my fuel injectors do you think it could be the cause of my truck shaking and idling choppy . (It doesn’t always shake it happens randomly when I start the vehicle)
It's shakes when you start because probably the injector stuck open and flood the cylider while it's off and when you first start it takes afew min to clear it
You don't have to take the entire fuel rail off just one side where one and 2 is and pop it back in make sure you clean before you getting it off and put oil on the orings
![โรงเรียนตอนตี 2 โคตรหลอน..!! [โรงเรียนไดเม่]](http://i.ytimg.com/vi/2MAEMwqVYh8/mqdefault.jpg)
Thanks for the video wish it was on how to take all 4 out
I'd check for fuel pressure and fuel pressure regulator
Thank you for this video
Thanks for the video, Abdel. My 98 4runner is giving me a hard time. It started hesitating when accelerating months ago, but it slowly got worse. Now it hesitates and surges when sitting on traffic lights, and it doesn't want to go when I give it gas. Its almost like the engine is starving for gas. I have no vacuum leaks whatsoever. Do I have to take off the fuel rail to replace all 4 fuel injectors or can I do the same procedure you are doing? Mine is 2.7, but they are identical.
Hello Bryan, did you check to see whats the fuel pressure is on your truck? Also do you smell gas when you first start it? Also did you check for codes?
@@abdelcarfix2770 I have a misfire in cylinder number 1 when I checked using my scanner. The fuel pressure is good, I took the truck to a mechanic about a month ago and he checked that. Tomorrow I plan on buying a 140 dollar fuel injector to see if that one cylinder gets better. If it does, I would just change all of them. What are your thoughts? The engine is stable when Idling in my driveway, but when I drive it its a different story. Yesterday was the last time I drove it. I had to put it in park in every red light so it would stop shaking. It was pretty embarrassing to say the least. The fuel filter is new, the O2 sensors are new, the spark plugs I bought about 5 months ago, ignition coils are new as well, etc. Thanks for your response :)
Sound like injector 1 is missfire and 5hose so common with injectors go bad. I would just change the first one and not the rest if they are good
@@abdelcarfix2770 was it difficult to pull the old o ring from the hole? Imma go to Autozone to see if i can get a pick set.
Do you have to do anything after installation like idle reprogramming, or just turn truck on and its ready?
No need need to do anything
I have a 2001 Tacoma 2.4l shakes when I start it sometimes and will idle rough . I got a code p0301 , cylinder one misfire ; check engine light was flashing . I replaced spark plugs,ignition coils ,mas sensor less than 5 months ago . I haven’t replaced any of my fuel injectors do you think it could be the cause of my truck shaking and idling choppy . (It doesn’t always shake it happens randomly when I start the vehicle)
It's very common with those trucks to have bad injectors. I have done alot of them.
It's shakes when you start because probably the injector stuck open and flood the cylider while it's off and when you first start it takes afew min to clear it
Thank you should I just replace the first one or all 4 of them ?
Cylider one is easy to replace I would just replace one.
You don't have to take the entire fuel rail off just one side where one and 2 is and pop it back in make sure you clean before you getting it off and put oil on the orings