I own a MB shop. These little bikes are so much fun. My oldest is a 66cc 80😂on a Schwinn Point Beach. 12 years old, bought the bike & kit at he same time. Rode it again today. 😎
@mattjones8016 in regards to tighter tolerance higher horsepower automotive side of things which there are exceptions to. N/A motors you do a quick warm up with the engine just idling. That helps flush out the motor and gets seals and rings in their operating condition. That's no more than 10 minutes max, normally a tuner will be next to the car or engine fine tuning the idle and afr. Drain oil and filter and you use a "straight weight" or break-in specific blend oil and if you have the luxury of being strapped to a dyno, break-in is done in around 45 minutes. The engines to seat rings need higher pressure followed by vacuum to help seat quicker. My honda engine for first 100 miles i drove i would floor it to around 5500rpm and let go of the gas and i was in a manual transmission car and on down to 2,000rpm and repeat. Highway would be best to get that done. If tolerances are correct then you're done. Change the oil using non synthetic for the first 3k miles. Then run whatever oil you want. Ive stuck to 15k mile full synthetic. Turbo and supercharged engines you do different, but this novel you get the point. 🫣🤘
Speed! Oh boy to be honest I'd be geared up going that fast. Knee and elbow pads just in case. I love my Evercross H5 but have to admit it does struggle on inclines and I often think I could use something like what you have a gas powered engine. Normal flat surface I get 27 mph and even that looks fast. 😄 Awesome job.
My new imaycc 80cc engine stock out of the box I got up to 35 mph with a 44 tooth sprocket I'm still breaking it in I ran one tank of gas through it so far. But I like your build that frame is nice I want to get one of those and I like how you went with the purple skulls and other purple parts it looks awesome my dude...🤙👍
I have the same kit doing 40 with the exhaust cap off. Does yours seem just a little sketch? I want a more reliable fast kit the imc seems like junk. Works for now for how long tho not sure
I got hydraulic rotor brakes for my new build jokester but they are still a line pull. The kit wasn’t expensive and it was really nice to have a basic easy setup that just bolts up to a stock set up and still have great clamping force. I read the other message we’re you mentioned you wanted to upgrade. I got purple too for my color since you want that color scheme too. Hit me up if you need a link and all.
@@musaguz6783 it was 40-45 bucks for two hydraulic calipers and cables and 2 160mm rotors in chosen anodized color. So to me that seemed like a really fair price
I have a 212 predator 6.5 horse motor on a modified mountain bike only modified for the wheels though the motor fit right inside the frame I do about 44 + miles an hour and it goes uphill like any other bike that has that torque to go up I have a torque converter on my bike and I get many miles out of my belts motors very reliable
Don't know why his bike went 40 plus but he should of Easily hit 50+ with that set up. My BBR100 goes 44mph that I got from Bike Berry, a couple weeks later the 100cc V2 came out. I missed on getting the better Version. I do have the Phantom V3 kit just waiting for the bike so I can install it. Lots of fun
@@lonneebelton9806 motorized bikes are lots of fun no matter what kind of motor you put on them as long as they're reliable to do their job (motorized bikes 4life)
And my motor does the job six-fold best motor I ever put on a bike 212 predator 6.5 horse that's where I'm going if I upgrade I'm putting a the 15.8 459cc predator motor that may be my next upgrade
@@lonneebelton9806 I just bought the BT 199 v2 for $230.00 on E bay and with a little wWindow Porting and polishing it should do close to 70mph. But then again I weight 125 soaking wet. I cant wait to get it broke in!👍
Nice runs just like mine once it's heat soaked you can bring the rpm down by letting off the throttle for a few seconds then clutch it works well for me running stock as well 79kph has been my max speed. My homebuild shouldn't go that fast but it's fun.
I so wish they'd make a full suspension Felt Faker type motorized bicycle frame that could run either 26 or 29in wheels. Even a cheap rear shock is way better than a hardtail. It'd take lot's of stress off both the frame & Rider. You could upgrade to better forks & rear shock that have true compression, damping & rebound function. Maybe also add mounting tabs on the frame for optional jack shaft kit. Full suspension Felt Faker with 203mm F&R disc brakes 👍
@@jimstenlund6017 I have a suspension seat post & cushy spring seat which does help some. But there's a very good reason why 🛵 and motorcycles added rear suspension. Even better, if the frame had a rear long travel MTN shock. With a decent long travel front shock. You could ride a 52mm 2 stroke like a dirt bike off jumps. It'd make these motorized bikes even more fun.
Got my bullet train electric start completely rebuilt with a billit machined liquid cooled head forged pistons crank and Conrod were already pretty strong double spark plug ports 2 stroke EFI & a smart carb water pumps are electric too so no power lose as if it were a crank driven pump & alternator already uses crank power amazon exhaust with expansion chamber and a welder shop did all the measurements for chains and gears to gear the engine to the crank peddles cut the peddles and cranks off so its balanced & just a gear welded a stationed gear from the engine to the crank and was able to use a regular bike chain from there with a mountain bike 6 or 7 speed transmission ran on ethanol with 2 stroke oil never could dyno it but it blew up the CVT clutch after a burnout drove it but was scared to reach top speed but id say i hit probably almost 90 mph 6 gear and was 70% throttle at like 6,800 rpm running at like 190 degrees after a warmup id say maybe making like 15/20 hp had a cheap engine temperature tack and rpm reader you can get for like $15 or less on Amazon its pretty accurate just gotta wrap a wire around a spark plug and go into the settings and set it for 2 stroke engine
People put predator 212s on bikes and the normal one makes double the power than the phantom, the kart racing version could probably push even more. The engines are also cheaper.
Looks awesome brother I have version 2 but I did some of my own stuff on the inside like you I swapped it for stihl products on the inside and it working ok for right now ride safe brother I'll be watching for your test ride
Hi there , love your videos, looking for some advice, I am hoping to bring a bike and motor on a flight Newark to Havana Cuba , I live there during the winter but have no transportation. Could you recommend a bike and engine combination that would be reliable, need good suspension as the roads are non existent. I have basic tools in my house but I could buy in the states what I need , would you recommend 2 of 4 stroke , I don’t need to go fast because the roads don’t permit it but I need reliable machine as my wife might also need to use it and I don’t want it breaking down all the time . Best regards John .
You should get yourself a standard PK80 66cc kit. I'd suggest you dont buy the cheapest, nor the most expensive, but something in between. AVOID BIKEBERRY! The normal 66cc kits have everything you need, but the first upgrade you should do is a new #41 chain. The stock kit chains are trash and will fail quickly. I suggest you build it ahead of time and get all the little china crap fixed before it becomes critical. These bikes ALWAYS go through a phase where everything gets loose and you need to sort it out to get reliability. Once you ride it a few days or weeks, it will kinda "take a set" and stuff stops falling off (assuming you fix & tighten) You also need to check Cuban laws as these bikes might not be legal, depending on the area, etc. I know a couple guys in Cuba who ride, and they mostly complain about not being able to get any parts. So bring your own spares and you can probably get back some of your investment by selling the bike/motor when done. They eat up parts when available like crazy down there!
Kindly question can we remove the paddle part and change to normal steel pipe to make leg balance like normal motorcycle and we change the start button to make the engine work without paddle
225. You might need a better carb. I installed a 23mm oz reed intake and added a mikuni vm18-144 carb and tuned it. Now my bike does 47 with the stock pipe. I should do 55-58 with a real expansion chamber.
@MJTechChannel I'm putting one of these on a chopper bike soon. I'm getting engine and components that you mentioned. How do you go about "tuning it"?
I've been through 2 now. Not sure what I'm doing wrong but I use the best oil and on the first the piston melted to the wall in 7 minutes. I love the power but haven't had any luck with them
wow that's amazing. i was hesitant to buy a v1 or v2 phantom in the past hmm so i did'nt, but now i will soon buy v3. do you have an online link to the manual booklet @1:25 ?
the stock tensioner tends to twist inwards towards the wheel, and it would wreck the spokes. @10:35 have you upgraded that stock one ? and what other tensioner did you choose?
if you could reply that would be great How fast were to able to after break in and how far were you able to go on one tank thinking about getting an 80-100+cc bike to get to the next town for school it’s about 8mi there.(i can leave gas at a friends house so getting back won’t be an issue) (with 6 miles on a county road) don’t want to pay car insurance get a car because it will prob cost me more
@@MJTechChannel hi great video I just picked up a used f-zero please help what engine would you put on this I like this engine alot but I'm so undecided I'm sking please what engines would you go with top 3 in order
A motor runs off electricity, what you have is called an engine, it’s naturally aspirated with a carburetor that runs off gasoline. And that would be called a skull, a skeleton is a human body with everything but the bones missing.
I own a MB shop. These little bikes are so much fun. My oldest is a 66cc 80😂on a Schwinn Point Beach. 12 years old, bought the bike & kit at he same time. Rode it again today. 😎
Then I need you're help...where are you located please ?
Central Mass.
Dude it don't matter where m I at...
Yeah .it's fun .
I got nine builds in the belt
dang man straight full throttle on a brand new engine.
and pops the clutch and immediately starts going doesn't even hold clutch in to let it warm up after it starts
You know engines from factory are floored max revs for 10sic before leaving the factory
@@Rain-kg4bj is this the truth bc i did not know this
@mattjones8016 😂 no it's not they don't do this and I've seen them blow out doing stupid shit before the break in is done due to over heating
@mattjones8016 in regards to tighter tolerance higher horsepower automotive side of things which there are exceptions to. N/A motors you do a quick warm up with the engine just idling. That helps flush out the motor and gets seals and rings in their operating condition. That's no more than 10 minutes max, normally a tuner will be next to the car or engine fine tuning the idle and afr. Drain oil and filter and you use a "straight weight" or break-in specific blend oil and if you have the luxury of being strapped to a dyno, break-in is done in around 45 minutes. The engines to seat rings need higher pressure followed by vacuum to help seat quicker. My honda engine for first 100 miles i drove i would floor it to around 5500rpm and let go of the gas and i was in a manual transmission car and on down to 2,000rpm and repeat. Highway would be best to get that done. If tolerances are correct then you're done. Change the oil using non synthetic for the first 3k miles. Then run whatever oil you want. Ive stuck to 15k mile full synthetic. Turbo and supercharged engines you do different, but this novel you get the point. 🫣🤘
these are awesome motor kits have built 3 now and all great 50mph after breakin :)
what mods?
@@rylibritton8406none mines stock got it up to 51mph
Im about to order mine right now. Thanks for putting me on to this!
Speed! Oh boy to be honest I'd be geared up going that fast. Knee and elbow pads just in case. I love my Evercross H5 but have to admit it does struggle on inclines and I often think I could use something like what you have a gas powered engine. Normal flat surface I get 27 mph and even that looks fast. 😄 Awesome job.
😢😢
My new imaycc 80cc engine stock out of the box I got up to 35 mph with a 44 tooth sprocket I'm still breaking it in I ran one tank of gas through it so far. But I like your build that frame is nice I want to get one of those and I like how you went with the purple skulls and other purple parts it looks awesome my dude...🤙👍
I have the same kit doing 40 with the exhaust cap off. Does yours seem just a little sketch? I want a more reliable fast kit the imc seems like junk. Works for now for how long tho not sure
These little engines are so cute. I’m going to put one on my bike.
That can work?
I got hydraulic rotor brakes for my new build jokester but they are still a line pull. The kit wasn’t expensive and it was really nice to have a basic easy setup that just bolts up to a stock set up and still have great clamping force. I read the other message we’re you mentioned you wanted to upgrade. I got purple too for my color since you want that color scheme too. Hit me up if you need a link and all.
Depends what you call expensive 🫰 dude
@@musaguz6783 it was 40-45 bucks for two hydraulic calipers and cables and 2 160mm rotors in chosen anodized color. So to me that seemed like a really fair price
I still running gen 2 ⚙️ still running good
I have a 212 predator 6.5 horse motor on a modified mountain bike only modified for the wheels though the motor fit right inside the frame I do about 44 + miles an hour and it goes uphill like any other bike that has that torque to go up I have a torque converter on my bike and I get many miles out of my belts motors very reliable
Don't know why his bike went 40 plus but he should of Easily hit 50+ with that set up. My BBR100 goes 44mph that I got from Bike Berry, a couple weeks later the 100cc V2 came out. I missed on getting the better Version. I do have the Phantom V3 kit just waiting for the bike so I can install it. Lots of fun
@@lonneebelton9806 motorized bikes are lots of fun no matter what kind of motor you put on them as long as they're reliable to do their job (motorized bikes 4life)
And my motor does the job six-fold best motor I ever put on a bike 212 predator 6.5 horse that's where I'm going if I upgrade I'm putting a the 15.8 459cc predator motor that may be my next upgrade
@@presleyfleckmotorizedbikef4285hi mate I’m looking at building one, what engine do you Segway for decent power? Cheers
@@lonneebelton9806 I just bought the BT 199 v2 for $230.00 on E bay and with a little wWindow Porting and polishing it should do close to 70mph. But then again I weight 125 soaking wet. I cant wait to get it broke in!👍
Hey brother thanks for posting. I planning on making my own phantom cause it just seems like the right move. Definitely need all that power.
Very nice I will be getting that engine soon thanks for reviewing that engine.
Nice runs just like mine once it's heat soaked you can bring the rpm down by letting off the throttle for a few seconds then clutch it works well for me running stock as well 79kph has been my max speed. My homebuild shouldn't go that fast but it's fun.
Awesome. I have a 80cc, BMX,old school frame. Wiss I could buy a bike like that. Wow sweet.
Another great video. Thanks for Sharing bro Finally got nice weather up here so I got my bike back out finally so I can start making videos again
Just waiting for mine to arrive 😃👍🏻
Nice clean build, keep up the great videos! Bikes by Bill.
You never mentioned what size sprocket you chose ... Thats really important in regards to the top speed ...36 tooth 44 tooth or 48 tooth ???
He said 36
The very first part of the unbox was the sprocket. I believe he said 44 tooth.
I'm buying one really soon that was sweet be great to ride back and forth fishing it would cost next to nothing for for gas
I so wish they'd make a full suspension Felt Faker type motorized bicycle frame that could run either 26 or 29in wheels. Even a cheap rear shock is way better than a hardtail. It'd take lot's of stress off both the frame & Rider. You could upgrade to better forks & rear shock that have true compression, damping & rebound function. Maybe also add mounting tabs on the frame for optional jack shaft kit. Full suspension Felt Faker with 203mm F&R disc brakes 👍
Good Springer seat should help
@@jimstenlund6017 I have a suspension seat post & cushy spring seat which does help some. But there's a very good reason why 🛵 and motorcycles added rear suspension. Even better, if the frame had a rear long travel MTN shock. With a decent long travel front shock. You could ride a 52mm 2 stroke like a dirt bike off jumps. It'd make these motorized bikes even more fun.
Nice content my guy!
"No Motorized Bike Engine Will Go Faster At This Price" hold my Dremel.
What should my mix ratio be for the phantom? For brak in?
Hell yeah i am gonna get a motorized bike 🚲🚲🚲🚲
How is Phantom eighty five running❤
Got my bullet train electric start completely rebuilt with a billit machined liquid cooled head forged pistons crank and Conrod were already pretty strong double spark plug ports 2 stroke EFI & a smart carb water pumps are electric too so no power lose as if it were a crank driven pump & alternator already uses crank power amazon exhaust with expansion chamber and a welder shop did all the measurements for chains and gears to gear the engine to the crank peddles cut the peddles and cranks off so its balanced & just a gear welded a stationed gear from the engine to the crank and was able to use a regular bike chain from there with a mountain bike 6 or 7 speed transmission ran on ethanol with 2 stroke oil never could dyno it but it blew up the CVT clutch after a burnout drove it but was scared to reach top speed but id say i hit probably almost 90 mph 6 gear and was 70% throttle at like 6,800 rpm running at like 190 degrees after a warmup id say maybe making like 15/20 hp had a cheap engine temperature tack and rpm reader you can get for like $15 or less on Amazon its pretty accurate just gotta wrap a wire around a spark plug and go into the settings and set it for 2 stroke engine
People put predator 212s on bikes and the normal one makes double the power than the phantom, the kart racing version could probably push even more. The engines are also cheaper.
Nice vid bud! She's nice...and stock.😳...I mite just have to put my china doll on the shelf this summer.
The one I got, the clutch plate flat nut , wasn't even screwed on buy 1/2 thread, clutch wasn't catching
how are these motors for mountain trail riding? can they handle steep hills etc?
More for a cruising experience
gear it down. 72 tooth on the back and a small drive sprocket. your top will be slow but you'll climb hills without slowing
@MJTECH i have a question please someone help me i bought 2 stroke oil does this phantom 85 need oil or just marine greese? mine came in yesterday
You went so fast the front tire looked glitchy 😆. U almost traveled back in time.
Holy smokes you definitely need to upgrade the Brakes eventually.
Yes sir, going with hydraulic soon
More like immediately
8:54 - этот передний поворотный кронштейн, который тут видно, он из комплекта поставки, или он самодельный?
What ratio do they recommend for break in? I heard 20 to 1 but that's a lot of oil
20:1 is good
@@Scooterbruh554 I'm way passed the break in now
40:1 since day 1 is the best imo or you can start at 32:1 than switch to 40:1
Question for you What oil ratio are you using mine v2 is still 20:1 can I go less temperature only gets up to 235 degrees?
Hey Mike Miller do you Still have your phantom Motor?!
@@RaoulDuke224 yes I have to change the crank bearings and shell be up and going
does it still have torque with the 36t sprocket to go up steap hills??
*7:26** - what a part is that in this view point?*
Looks awesome brother I have version 2 but I did some of my own stuff on the inside like you I swapped it for stihl products on the inside and it working ok for right now ride safe brother I'll be watching for your test ride
8:54 - is this front swivel bracket which you can see here is it from the delivery kit or is it homemade?
Great for tension relief, after day of working!, great hobby if ya love tinkering
good stuff keep it up bro
Hi there , love your videos, looking for some advice, I am hoping to bring a bike and motor on a flight Newark to Havana Cuba , I live there during the winter but have no transportation. Could you recommend a bike and engine combination that would be reliable, need good suspension as the roads are non existent. I have basic tools in my house but I could buy in the states what I need , would you recommend 2 of 4 stroke , I don’t need to go fast because the roads don’t permit it but I need reliable machine as my wife might also need to use it and I don’t want it breaking down all the time . Best regards John .
You should get yourself a standard PK80 66cc kit. I'd suggest you dont buy the cheapest, nor the most expensive, but something in between. AVOID BIKEBERRY! The normal 66cc kits have everything you need, but the first upgrade you should do is a new #41 chain. The stock kit chains are trash and will fail quickly. I suggest you build it ahead of time and get all the little china crap fixed before it becomes critical. These bikes ALWAYS go through a phase where everything gets loose and you need to sort it out to get reliability. Once you ride it a few days or weeks, it will kinda "take a set" and stuff stops falling off (assuming you fix & tighten) You also need to check Cuban laws as these bikes might not be legal, depending on the area, etc. I know a couple guys in Cuba who ride, and they mostly complain about not being able to get any parts. So bring your own spares and you can probably get back some of your investment by selling the bike/motor when done. They eat up parts when available like crazy down there!
Nothing gives you more Dopamine than riding a slow bike fast as helllllllll
Kindly question can we remove the paddle part and change to normal steel pipe to make leg balance like normal motorcycle and we change the start button to make the engine work without paddle
Sir, what is the brand of the bike itself, with the integrated fuel tank ? Thanks !
How were the stock rims were they decent ? What gauge spoke were they?
How much do you weigh? My Phantom only reaches 40 mph with a 36t sprocket. I want more
225. You might need a better carb. I installed a 23mm oz reed intake and added a mikuni vm18-144 carb and tuned it. Now my bike does 47 with the stock pipe. I should do 55-58 with a real expansion chamber.
@@MJTechChannel thanks a lot.
@MJTechChannel I'm putting one of these on a chopper bike soon. I'm getting engine and components that you mentioned. How do you go about "tuning it"?
Mine will be in tomorrow
Hope you enjoy and break it in for a little, mines still running strong for months v2
Cool
What was the name of the bike frame? You put the engine on.
Do they make a quiet muffler for gas motor bicycles
Fantastic project!!!
Where did you get the vented gas cap from?
On Amazon
I've been through 2 now. Not sure what I'm doing wrong but I use the best oil and on the first the piston melted to the wall in 7 minutes. I love the power but haven't had any luck with them
V3 ?
What is the difference between V1, V2 and V3 kits?
Same displacement and power, just quality has been getting better and they redesigned the cylinder for it to be durable.
Awesome vid
Can it be made silent, improved, especially its loud transmission??
What's the fastest engine kit I can get for my cruiser deuce bicycle? I need it for work!!!
isnt the wrist pin supposed to have a needle bearing?
Hi may ask ask if you are using stainless rims or aluminum rims?
Good lookin bike
How much did you say the entire kit cost?
I think they are $299 now
Where can I buy the frame ?
wow that's amazing. i was hesitant to buy a v1 or v2 phantom in the past hmm so i did'nt, but now i will soon buy v3. do you have an online link to the manual booklet @1:25 ?
the stock tensioner tends to twist inwards towards the wheel, and it would wreck the spokes. @10:35 have you upgraded that stock one ? and what other tensioner did you choose?
Nice run
how well does the Engine break work does it slow you down?
Phantom 85 v3 with different carb and boost bottle? How fast will it go and what parts you prefer to use?
How do I get it fully assembled?
nice build
Is it reliable for long daily rides?
same question that i have since i feel like taking one to work
Where can i get a frame like this?
WHAT IS GAS MILEAGE USING “”THAT GAS TANK””? IS THAT GAS TANK SAME CAPACITY AS OTHER KIT’S TANKS?
if you could reply that would be great
How fast were to able to after break in and how far were you able to go on one tank
thinking about getting an 80-100+cc bike to get to the next town for school it’s about 8mi there.(i can leave gas at a friends house so getting back won’t be an issue) (with 6 miles on a county road)
don’t want to pay car insurance get a car because it will prob cost me more
What kind of gas are you supposed to use for this bike?
I want instead of motor gasoline engine, change to e-motor and how much it cost?
I bought one of these and I am regretting it big time having a very hard time with those damn piston clips
Yhi my name is joey I love it like that bike alot just wondering if you got one for sale I buy it
My angel fire 66/80cc from BBR hits 60
One day, i will make one that goes fast as well
Hopefully they keep em in stock.
I had this type of bike. But had work done to the motor. And mine went 60 mph
How is a Phantom 85 running?
Is that mph or kmh?
Chain clip should be going towards the motor
Him "everything's stock... except... everything"
Really need to change the title of this video since we got the avenger85
Excellent..
Someone make a nice expansion chamber exhaust for this !!!
Where is your gast tank?
Built in to the frame
What kind of bike is that!
By far the best motor on the market for 300 bucks
Definitely not.
@@QualityTransferswhat’s the best? Am planning on turning my downhill bike into one lol
i bought v3 but on the sticker it says its v2
a firestorm will get you 40-45 stock out the box.
I am doing a comparison soon
It won't do that stock
Like the bike can I buy off of you
It is for sale now
@@MJTechChannel hi great video I just picked up a used f-zero please help what engine would you put on this I like this engine alot but I'm so undecided I'm sking please what engines would you go with top 3 in order
A motor runs off electricity, what you have is called an engine, it’s naturally aspirated with a carburetor that runs off gasoline. And that would be called a skull, a skeleton is a human body with everything but the bones missing.
🤓🤓
sweet but scary ! 23mph on my ebike is fast enough for me ! but it's an awesome bike ! have you got pulled over by a cop yet ?
It’s a very cool bike indeed. Been making them for 12+ years and have never been stopped. 😊
Awesome
A little air leak?
You haven't broken it in yet!!!!
I want to get one for work, but I am sure that the cops would pull me over; It is so loud.
You can add silencers
@@MJTechChannel what are these silencers? And where do I get them? Thanks.
Must save !