Armoured Cable Glanding and Termination process || Power Cable

[@avilaringoy]

Good job sir

[@CrazyMe30]

Thanks for watching

[@JamellakateSacopon-l2u]

Thanks master.. to share your knowledge..more power master

[@CrazyMe30]

Thank you for watching

[@ariomulyadi]

terima kasih atas berbagi ilmu anda kawan...
saya dari indonesia.

[@CrazyMe30]

Thank you for watching

[@007floppyboy]

Great job, nice to see the inner sleeve left longer than the gland base, too many folk cut it right back and you end up with single layer of insulation next to the rough gland inner.
That would pass a Chemical plant inspection if it was an E1FW gland.
If you use adaptors, the inner sleeve should go past them by at least 10mm though.
I think 3 and 4 look a bit short on the inner sleeve.

[@CrazyMe30]

Thanks brother appreciate your suggestion

[@zubairalam1669]

Nice

[@shaynemacdonald3051]

You should be using CW glands for outside.

[@CrazyMe30]

Thanks for watching!

[@mcryptonite6948]

That is a CW gland.

[@CrazyMe30]

It is a double compression gland, CW is specially use for outdoor applications and where necessary to provide an IP66. Regards & thanks for watching

[@shaynemacdonald3051]

That is a BW gland

[@CrazyMe30]

Single compression for indoor use

[@Zombie_Longwinger]

I’d redo the first one get more bend on it

[@arghiegonzales8420]

i think this site is in emirates hills 🙂🙂

[@SimsonRitonga]

Best

[@CrazyMe30]

Thank you for watching

[@zayn-mallik4168]

What is the procedure for cable termination...this video all about how to gland the cable

[@CrazyMe30]

It depends on what you are going to terminate from LOw voltage to High voltage

[@paulharrison6408]

First cable too long tbh. I would advise not cutting the inner insulation off until after it's in the isolator. This avoids possible scratching of the core insulation. If you score around the inner insulation first before inserting then the inner comes off easier . Good effort though my friend . Spent over 35 years doing swa btw lol 😆

[@CrazyMe30]

Thanks for the advice sir. Stay safe

[@sitasuthar9827]

👍👍👍👍

[@josecastillo3801]

Good job bosing..Ilan ang FLc mo 35mm ba Yan o 50mm..stay safe God bless

[@CrazyMe30]

50mm po sir.

[@shaynemacdonald3051]

Wrong glands and no IP washers used.

[@gcbbuildingproject4782]

THIS CABLES I THINK FOR AIR HANDLING UNITE SUPPLY.

[@CrazyMe30]

EXACTLY

[@closeplus1225]

Pls use lug

[@रोमीमगर]

😍😍😍

[@paulpink9518]

Looks terrible you had loads of on the cables but you fucked the bends up totally.

[@CrazyMe30]

Thats the customers req😁

[@androb.]

Nakakairita Ang ganyang disconnect switch master Lalo na yong selector type. Mag termination ka ng 10mm wire. Masakit sa kamay.

[@CrazyMe30]

Yes boss tyaga lng hehe, salamat po

[@lilysofficialchannel]

Ang hirap gawin hehe

[@CrazyMe30]

Kaya po yan basta pag aralan lng maigi. Ingat po

[@doipardede321]

No good....!🤭

[@litoolindo1368]

Wrong glanding

[@CrazyMe30]

Thank you sir. Appreciate your comment. Stay safe

[@ruelolandria7758]

Dress properly your cable