One of my favorite things I've gotten recently was instead of buying heat shrink pre-cut like that buy it by the roll in the most common sizes I work with. I get the good 3X shrink marine stuff. I like getting longer lengths because I use it for all sorts of other stuff like adding chafe resistance to a wire without looming it. Works really nice for tool handles as well.
Remember when harbor freight had $5 sales on power tools? Drillmaster brand. I think they did a drill, 4" grinder, heat gun and maybe one other tool. I can't remember. Anyway, thats the heat gun i have and use it more than most people probably. I do body work for a living and use it a lot repairing bumper covers. Its probably the best $5 ive ever spent. Haha
I bought the warrior heat gun at HF for like $10. Use it often for electrical wires mostly and I laugh all the time when I think it was $10 and I see $60-$100 ones that do the same thing
Couldn’t agree more with literally everything you said here! I work for a high end European automaker and when it comes to wiring repairs, the only thing they allow you to use is their approved solder heat shrink ReyChem things. They use them from the factory and they’re awesome! However I have never EVER had any luck with getting a good joint out of them. I dunno how the factory does it, but no matter what, I couldn’t. They probably have a few million dollar machines that do it. Over the years I tried at least ten different heat guns and untold number of heat settings, distances, time, adapters, even the very pricey factory gun. No matter what I did I could never get a connection I was comfortable with. Same goes for all my coworkers too. So since I know how to solder and I think I’m pretty good at it, I took every single one of those solder shrink terminals and through them in the trash. I then soldered the old school way with dual wall adhesive lined heat shrink. Never ever had an issue with any repairs done like that! PS. At least in my world, there was two different types of that cloth tape. There was a tighter weave for wiring exposed to the elements, and a looser less expensive weave meant only to be used in the interior. Obviously you can use the tighter weave exterior tape in the interior but the looser weave interior tape will not last long when used on the exterior. I dunno how Amazon or other places sell it, but best to stick with just the one tighter weave and never worry about. The brand my company uses is Tesa. Damn good harness tape!
I really do like the double walled heatshrink tubing where the glue seals it water tight. I also like the heatshrink connectors that does the same. Never used the solder connectors. Never had an issue with the heatshrink connectors.
@@jacksmith2315 Yeah I dunno what it is, but I’ve never had any luck with the solder shrink connectors. What heat shrink connectors are you referring to? Does it have a mechanical connection of some type?
@@2down4up no there's no solder in them. Its pretty much them samething, but wo the solder. Like a combination of the double wall heatshrink tubing and an insulated crimp connector, so you get the strength of the crimp connector, and the sealing ability of the double wall heatshrink tubing all in one connector
The correct way to crimp is opposite the seam. That comes from MECP, Mobile Electronics Certification Professionals. Also, when you used the hydraulic crimper you should turn the terminal so the crimp lands on the seam, not the sides.
I'm a retired USAF Tactical Fighter Mechanic. I can't say enough how the 'right' tools make the job cleaner, and simpler and ultimately properly done, so certainly job well done on this breakdown. Your comment on the in-line solder connectors is absolutely true; the risk of heating the solder connector to its potential to tearing/burning and re-exposing the wire is a true concern. Only quality connectors should be used from quality manufactures, and then still, I go over them with heat shrink just because. * My only down side 'comment' would be to caution individuals over the 'Oyviny' Electrical tape. They are NOT UL or SA certified and therefor do NOT have the same protective properties as 3M does. Just something to consider on your OWN particular setting, use and decision making.
First off, thank you sir for your service. It is because of you that we are free. I've always been impressed with the care and methodology of aircraft mechanics and machinists; even moreso a tactical fighter mechanic. Thank you for the compliments. Great point on the Oyviny cloth tape. My point there was not to be an insulator, but only as a harness wrap to keep all the wires contained and give a more aesthetic look. Thanks again for watching and commenting.
@@Shoptoolreviews Thank YOU for the immensely generous response! I 100% agree with you on your follow up point! Personally I do have a special place for that fabric tape in my collection as well, for the points you clarified. As they say, a time and place for everything - and every tool and you nailed it on that specific point. Thoroughly enjoyed the vid! Keep em’ coming!
I bought the hydraulic crimper a few years ago and they were were a lot cheaper, but I would pay the new price in a heartbeat if mine breaks. I highly recommend it to anyone who makes batteryy cables up, does car audio, or anything with 4g+ cable.
Temco is the original hydraulic crimper manufacturer. Got my boss to buy it for the shop as it was more expensive that the amazon chinese version but did such a better job, had more sized and crimped perfectly hexagonal
On the solder seal connectors, you can usually slide them past the joint then flux and solder the joint. Use the solder seal to seal it up... Then put heat shrink over it if you want extra protection
Great video. I discovered the cheap Amazon solder-heatshrink butt connector all in one, and I LOVE them. If you look close, you can see the Sauter flowing pretty well and they give me enough confidence to keep using them.
Always used the heat shrink solder joints in a dealer environment. I like to use a very small focused beam of hot air right on the center of the joint. I have and recommend heating further than you did in the video, until you visually see the wicking take place. Often by that point wire insulation is degrading if the beam of air is not fully focused and very small. Used to train my guys to look for heat shrink to shrink, pellet to collapse and finally pellet to flow and nearly disappear. Love them but have seen high failure rate if not fully melted.
I use the Klein 2005n for crimping and I bet they can crimp those. I use them so I can carry less tools in my bag every day. Nice long handles and they don’t go through insulation on those type of connectors
What I've found with seamed barrel electrical terminals is crimping on the backside sometimes opens the seam. One of the crimper jaws has a driving die (the part that pushes into the terminal, deforms the metal, and makes the crimp) the other jaw has a 'U' shaped receiver. When the driving die is jammed towards that receiver; the way the terminal deforms tries to pull the seam apart. A good demo is to crimp a non-tinned barrel on the seam, and then one from the back. The backside crimp will pull on the barrel in such a way that the seam tries to open up. It's tough to see / understand what I'm saying on a tinned barrel because the tinning usually holds the seam together. Hopefully what I'm saying makes sense!
We have that same hydraulic crimper and had to use the next smaller die for the #6 cables. But dang, that thing worked awesome! With a little practice, you can get it pretty tight with one hand, to a point that you can let go and the wire won't just fall out and you can finish with both hands.
One piece of advice I can give you, don't use the c-frame type of hydraulic crimper for large gauge wire, I have seen those shatter, get the H-frame type with the pin.
Get a fabric "Seam Ripper" tool for taking tape OFF wiring harnesses!!!! It's fast, EASY and Cheap....and beats the hell outta using a razor or knife!!!!
Pistol grip automatic wire strippers. HF had Quinn now Pittsburgh. Last 3-6 months. Lifetime warranty. Get 2. Best thing ever for 12V wiring. Snapon and other tool trucks have them with lifetime warranties too. Also need some wire stripping pliers sometimes For crimping Knipex pliers wrench. Tremendous crushing force. Smooth jaws don’t break insulation. My current 12V wire tools are southwire cutters. Knipex pliers wrench. Pittsburgh pistol grip strippers. SnapOn wire stripper cutter crimpers and Snapon torch. RV tech. Lots of 12v wiring. And southwire DC clamp multi meter The big battery lugs. Yeah the big hydraulic is nice. But even working on RVs gets used once a week. And push come to shove the Knipex will crimp large connectors, just keep working closer. One of reasons for knipex over icon. The knipex pliers wrench have just that little bit of extra opening at each position.
Tried the solder seal wire a few times but don't care for it. Sometimes the soder in the center will get dislodged. Probably user error. Much prefer non insulated butt connectors and heat shrink tubing. Tesa 51036 is excellent for more than just wires.
I have all if these except for the heatshrink/solder connection combos. I haven't tried them out, but I have very high doubts that they work as well as traditional solder.
For the ratcheting crimpers and connectors? Why do you recommend non insulated over insulated? I would think you'd get more use with insulated. Not all connections and be used with non insulated, but can be used with insulated. The insulated heatshrink connectors with the ratcheting crimpers are great. I guess you can use heatshrink tubing with non insulated if you need to, i just find the insulated connectors better, especially the heatshrink ones where the glue melts and seals them. I do have heatshrink tubing with the sealing glue, but the outside is clear so you can see everything, but i never use it because i just use the heatshrink connectors. Also, i crimp on the seam. Seems to be a better crimp. I always thought they were made to crimp on the seam. Edit: ah. I asked too soon. You did answer my question in the vid lol. I get that you can see it better, but ive never had a problem w the heatshrink connectors. They're transparent so i can see the crimp. I dont like the cheaper non heatshrink ones. You cant see the crimp, and i always felt they never gave as good as a crimp, and they arent water tight
I always crimp on the seams, why? Because thats how I was told to do it 50 years ago, right or wrong I don't know but you couldn't separate them. That's a great list I'm going to order the little scissors.
if the seam is brazed shut, it may be ok to crimp on the seam, but as a matter of principal, ALWAYS crimp on the solid side. its how teh manufacturer lists them, therefore, it MAY be illegal depending on the codes and where/how its used.
Hot with that spinning thing closed. And of course, cool with the spinny think open til the element is cooled off. Wait, how many flavors have you got on yours,???? Sounds neat!!!
The wire harness tape that you want to buy is made by TESA. It's the same tape used in most brands of European luxury/sports cars and not that cheap chinese stuff that will not stand up to any heat.
I may have misunderstood and you probably already know (or maybe I’m just confused, lol) but about your wire crimper you showed( second one) you can buy different crimping dyes. They slide out. I have one with 5 or 6 sets of dyes👍 Good picks.
Coincidentally I already own all these except for the hydraulic crimper. The crimpers available at the time I needed a 0 gauge crimper were well over $150 so I went the hammer tool route. Why is the cordless heat gun so slow? I think I grew a couple additional gray hairs while watching it melt solder. Geez
Not this set, but you can get ratcheting crimpers specifically for insulated connectors, or you can can crimpers that have changeable jaws for insulated, non-insulated, etc.
I’ve been very disappointed with the solder sleeves. They are more of a pain than crimping, and heads up, they DON’T give you a better connection. I have them just to mix it up a bit, but crimping is pretty much the way to go.
Those styles of crimping tools are a waste of money. I've literally purchased 2 hydraulic crimping sets only used them 1 to 2 times and they both malfunctioned just from sitting in their cases in climate controlled storage.
@@Shoptoolreviews there are Two NHL teams in Florida but I digress. Amazon sells everything. However I do agree that “style of tape is very good for making things look neat and professional. Thankx for the video BTW
Tim I hate your videos!!!! Why you ask??? Because every time I watch your videos I say to myself that could come in handy and end up buying more tools. I need help seriously
I must confess - I must have misread the title of this video. I thought it said something about "must have tools" or 'tools you need!!" But here I am, 15 minutes in to this video and not only are these tools completely unnecessary, they aren't things that any normal person would think thinking about. Complete trash. As an ACTUAL MECHANIC (like I actually touch cars n stuff) absolutely not once have I ever thought to myself, "hmmmmm I could really crime some wires or get after that electrical system." Man I normally like this channel but this is pure clickbait for the computer crowd. These aren't tools, nobody has ever actually thought about wires and crimps and electrical toy boxes. Awful video - biggest waste of time I've experienced in years
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
One of my favorite things I've gotten recently was instead of buying heat shrink pre-cut like that buy it by the roll in the most common sizes I work with. I get the good 3X shrink marine stuff. I like getting longer lengths because I use it for all sorts of other stuff like adding chafe resistance to a wire without looming it. Works really nice for tool handles as well.
I always crimp on the back side rather then on the seam
Remember when harbor freight had $5 sales on power tools? Drillmaster brand. I think they did a drill, 4" grinder, heat gun and maybe one other tool. I can't remember. Anyway, thats the heat gun i have and use it more than most people probably. I do body work for a living and use it a lot repairing bumper covers. Its probably the best $5 ive ever spent. Haha
I bought the warrior heat gun at HF for like $10. Use it often for electrical wires mostly and I laugh all the time when I think it was $10 and I see $60-$100 ones that do the same thing
@Mr1234512 I use a mini torch or my lighter for wiring but it's wild how long some of this cheap stuff lasts.
You are right on crimping procedure !!
Those helping hands are solid.
You’re killing my bank account…lol. Great video with a lot of great information, especially for those like me who are weekend warriors.
Couldn’t agree more with literally everything you said here! I work for a high end European automaker and when it comes to wiring repairs, the only thing they allow you to use is their approved solder heat shrink ReyChem things. They use them from the factory and they’re awesome! However I have never EVER had any luck with getting a good joint out of them. I dunno how the factory does it, but no matter what, I couldn’t. They probably have a few million dollar machines that do it. Over the years I tried at least ten different heat guns and untold number of heat settings, distances, time, adapters, even the very pricey factory gun. No matter what I did I could never get a connection I was comfortable with. Same goes for all my coworkers too. So since I know how to solder and I think I’m pretty good at it, I took every single one of those solder shrink terminals and through them in the trash. I then soldered the old school way with dual wall adhesive lined heat shrink. Never ever had an issue with any repairs done like that!
PS. At least in my world, there was two different types of that cloth tape. There was a tighter weave for wiring exposed to the elements, and a looser less expensive weave meant only to be used in the interior. Obviously you can use the tighter weave exterior tape in the interior but the looser weave interior tape will not last long when used on the exterior. I dunno how Amazon or other places sell it, but best to stick with just the one tighter weave and never worry about. The brand my company uses is Tesa. Damn good harness tape!
I really do like the double walled heatshrink tubing where the glue seals it water tight. I also like the heatshrink connectors that does the same. Never used the solder connectors. Never had an issue with the heatshrink connectors.
@@jacksmith2315 Yeah I dunno what it is, but I’ve never had any luck with the solder shrink connectors. What heat shrink connectors are you referring to? Does it have a mechanical connection of some type?
@@2down4up no there's no solder in them. Its pretty much them samething, but wo the solder. Like a combination of the double wall heatshrink tubing and an insulated crimp connector, so you get the strength of the crimp connector, and the sealing ability of the double wall heatshrink tubing all in one connector
@@jacksmith2315 Ohhhhh ok so it’s a crimp connection wrapped in double wall heat shrink?
@@2down4up yes, exactly
The correct way to crimp is opposite the seam. That comes from MECP, Mobile Electronics Certification Professionals. Also, when you used the hydraulic crimper you should turn the terminal so the crimp lands on the seam, not the sides.
I'm a retired USAF Tactical Fighter Mechanic. I can't say enough how the 'right' tools make the job cleaner, and simpler and ultimately properly done, so certainly job well done on this breakdown. Your comment on the in-line solder connectors is absolutely true; the risk of heating the solder connector to its potential to tearing/burning and re-exposing the wire is a true concern. Only quality connectors should be used from quality manufactures, and then still, I go over them with heat shrink just because. * My only down side 'comment' would be to caution individuals over the 'Oyviny' Electrical tape. They are NOT UL or SA certified and therefor do NOT have the same protective properties as 3M does. Just something to consider on your OWN particular setting, use and decision making.
First off, thank you sir for your service. It is because of you that we are free. I've always been impressed with the care and methodology of aircraft mechanics and machinists; even moreso a tactical fighter mechanic. Thank you for the compliments. Great point on the Oyviny cloth tape. My point there was not to be an insulator, but only as a harness wrap to keep all the wires contained and give a more aesthetic look. Thanks again for watching and commenting.
@@Shoptoolreviews Thank YOU for the immensely generous response! I 100% agree with you on your follow up point! Personally I do have a special place for that fabric tape in my collection as well, for the points you clarified. As they say, a time and place for everything - and every tool and you nailed it on that specific point. Thoroughly enjoyed the vid! Keep em’ coming!
I bought the hydraulic crimper a few years ago and they were were a lot cheaper, but I would pay the new price in a heartbeat if mine breaks. I highly recommend it to anyone who makes batteryy cables up, does car audio, or anything with 4g+ cable.
Temco is the original hydraulic crimper manufacturer. Got my boss to buy it for the shop as it was more expensive that the amazon chinese version but did such a better job, had more sized and crimped perfectly hexagonal
That tape is known as Tesa tape for factory style harnesses 👍
On the solder seal connectors, you can usually slide them past the joint then flux and solder the joint. Use the solder seal to seal it up... Then put heat shrink over it if you want extra protection
Underrated channel.
Nice call!!! Nicely said!!!
Great video. I discovered the cheap Amazon solder-heatshrink butt connector all in one, and I LOVE them. If you look close, you can see the Sauter flowing pretty well and they give me enough confidence to keep using them.
Always used the heat shrink solder joints in a dealer environment. I like to use a very small focused beam of hot air right on the center of the joint. I have and recommend heating further than you did in the video, until you visually see the wicking take place. Often by that point wire insulation is degrading if the beam of air is not fully focused and very small. Used to train my guys to look for heat shrink to shrink, pellet to collapse and finally pellet to flow and nearly disappear. Love them but have seen high failure rate if not fully melted.
I use the Klein 2005n for crimping and I bet they can crimp those. I use them so I can carry less tools in my bag every day. Nice long handles and they don’t go through insulation on those type of connectors
What I've found with seamed barrel electrical terminals is crimping on the backside sometimes opens the seam. One of the crimper jaws has a driving die (the part that pushes into the terminal, deforms the metal, and makes the crimp) the other jaw has a 'U' shaped receiver. When the driving die is jammed towards that receiver; the way the terminal deforms tries to pull the seam apart.
A good demo is to crimp a non-tinned barrel on the seam, and then one from the back. The backside crimp will pull on the barrel in such a way that the seam tries to open up. It's tough to see / understand what I'm saying on a tinned barrel because the tinning usually holds the seam together.
Hopefully what I'm saying makes sense!
We have that same hydraulic crimper and had to use the next smaller die for the #6 cables. But dang, that thing worked awesome! With a little practice, you can get it pretty tight with one hand, to a point that you can let go and the wire won't just fall out and you can finish with both hands.
One piece of advice I can give you, don't use the c-frame type of hydraulic crimper for large gauge wire, I have seen those shatter, get the H-frame type with the pin.
Get a fabric "Seam Ripper" tool for taking tape OFF wiring harnesses!!!! It's fast, EASY and Cheap....and beats the hell outta using a razor or knife!!!!
I use a seat belt cutter. Works like a charm, and doubles up as a letter opener.
Pistol grip automatic wire strippers. HF had Quinn now Pittsburgh. Last 3-6 months. Lifetime warranty. Get 2. Best thing ever for 12V wiring. Snapon and other tool trucks have them with lifetime warranties too. Also need some wire stripping pliers sometimes
For crimping Knipex pliers wrench. Tremendous crushing force. Smooth jaws don’t break insulation.
My current 12V wire tools are southwire cutters. Knipex pliers wrench. Pittsburgh pistol grip strippers. SnapOn wire stripper cutter crimpers and Snapon torch. RV tech. Lots of 12v wiring. And southwire DC clamp multi meter
The big battery lugs. Yeah the big hydraulic is nice. But even working on RVs gets used once a week. And push come to shove the Knipex will crimp large connectors, just keep working closer. One of reasons for knipex over icon. The knipex pliers wrench have just that little bit of extra opening at each position.
Tried the solder seal wire a few times but don't care for it. Sometimes the soder in the center will get dislodged. Probably user error. Much prefer non insulated butt connectors and heat shrink tubing. Tesa 51036 is excellent for more than just wires.
I believe you’re supposed to crimp on the seem so it curls in and grabs the wire. Almost like a heart shape with a rounded bottom.
I have all if these except for the heatshrink/solder connection combos. I haven't tried them out, but I have very high doubts that they work as well as traditional solder.
If you turn the tape sticky side up, regular scissors cut it fine!
For the ratcheting crimpers and connectors? Why do you recommend non insulated over insulated? I would think you'd get more use with insulated. Not all connections and be used with non insulated, but can be used with insulated. The insulated heatshrink connectors with the ratcheting crimpers are great. I guess you can use heatshrink tubing with non insulated if you need to, i just find the insulated connectors better, especially the heatshrink ones where the glue melts and seals them. I do have heatshrink tubing with the sealing glue, but the outside is clear so you can see everything, but i never use it because i just use the heatshrink connectors. Also, i crimp on the seam. Seems to be a better crimp. I always thought they were made to crimp on the seam.
Edit: ah. I asked too soon. You did answer my question in the vid lol. I get that you can see it better, but ive never had a problem w the heatshrink connectors. They're transparent so i can see the crimp. I dont like the cheaper non heatshrink ones. You cant see the crimp, and i always felt they never gave as good as a crimp, and they arent water tight
Nice comment
All of it, Stand Up Guy!!!!
I always crimp on the seams, why? Because thats how I was told to do it 50 years ago, right or wrong I don't know but you couldn't separate them.
That's a great list I'm going to order the little scissors.
if the seam is brazed shut, it may be ok to crimp on the seam, but as a matter of principal, ALWAYS crimp on the solid side. its how teh manufacturer lists them, therefore, it MAY be illegal depending on the codes and where/how its used.
I deal with car audio and recently got a few of these items. That crimping tool will be my next purchase
When I use the solder butt connectors when they're still liquid I pinch them real quick this make sure it gets embedded
Crimp on the seam is the strongest. I calibrate crimpers for my job.
Very nice list!!! I have most of that list and now going to buy the rest!!
Thanks for the information. May I ask at what temperature you set your heat gun for the heat shrink tubing?
Hot with that spinning thing closed. And of course, cool with the spinny think open til the element is cooled off. Wait, how many flavors have you got on yours,???? Sounds neat!!!
The wire harness tape that you want to buy is made by TESA. It's the same tape used in most brands of European luxury/sports cars and not that cheap chinese stuff that will not stand up to any heat.
The material type sticky stuff? Or the stuff with no glue? Or something else
Gotta Google it
Thanx!!!
I prefer the non-insulated terminals too. The insulation they put on doesn't realistically protect much
I have that yellow crimper. It's trash and the sizes you have to scale down like you said. I use it regularly and suggest a higher priced one.
Maximum heat allways use maximum heat level
I crimp on the back side opposite of the seam
By the way, don’t forget to insert connector and sleeve PRIOR to twisting wires together! Rarely can you slip up the back end like it was done here! 😂
I may have misunderstood and you probably already know (or maybe I’m just confused, lol) but about your wire crimper you showed( second one) you can buy different crimping dyes. They slide out. I have one with 5 or 6 sets of dyes👍
Good picks.
#1 - Harbor Freight, check. #2 - eBay, check. #3 - eBay, check. #4 - DX Engineering, check. #5 - eBay, check. #6 - eBay, check. #7 - Milwaukee, check. #8 - eBay, check. #9 - Basically, Friction Tape, check. #10 - Small Shear......GREAT IDEA! You cost me 6 bucks...LOL ! Great Post!
Coincidentally I already own all these except for the hydraulic crimper. The crimpers available at the time I needed a 0 gauge crimper were well over $150 so I went the hammer tool route.
Why is the cordless heat gun so slow? I think I grew a couple additional gray hairs while watching it melt solder. Geez
If it's not coming off it's a good crimp but I would do exactly what you did with the split seam do it on the back
Thanks for sharing
Wouldnt matter if i bought them all now , when i went to use them i won't be able to find them so ill order them again 😂
Soooo true
I try to collect up 3 of everything, little at a time. But I often start off with two, if it's a hot item. Things travel. Best of luck!!!
Will the ratcheting crimpers work on insulated connectors ?
Not this set, but you can get ratcheting crimpers specifically for insulated connectors, or you can can crimpers that have changeable jaws for insulated, non-insulated, etc.
Big uniform side crimper overkill but theyre never going anywhere with one on each side
Check out the Milwaukee scissors.
I’ve been very disappointed with the solder sleeves. They are more of a pain than crimping, and heads up, they DON’T give you a better connection. I have them just to mix it up a bit, but crimping is pretty much the way to go.
Add a dip of non corrosive flux too each wire
nice video
Thanks god bless
I do the non seem side
"AWG" Gauge. "cloth tape" Tessa Tape. Similar to going to a surgeon and hearing him say "nurse hand me that cutty thing so i can see this guys guts".
I crimp on the back side
Can you say gauge?
Always crimp on the side without the seam. Period.
Удивительно как американцы увидели ПГР-70
Those styles of crimping tools are a waste of money. I've literally purchased 2 hydraulic crimping sets only used them 1 to 2 times and they both malfunctioned just from sitting in their cases in climate controlled storage.
I've used mine sparingly over a few years and they have worked for me.
I will always crimp the backside
Why are you screaming dude?
WHAT???
Volume button broken?
@@RobertDorrell Turning down the volume doesn’t change the fact he’s yelling at the camera…
He's good at it. Always play to your strengths
As long as he's given you good info, just turn your volume down, no?
No self respecting Canadian would use automotive tape. It’s Hockey tape lol. I use it on everything..including hockey sticks.
Lol, sorry to steal the thunder. Not many hockey rinks or frozen ponds down here in Florida. Thanks for watching.
@@Shoptoolreviews there are Two NHL teams in Florida but I digress. Amazon sells everything. However I do agree that “style of tape is very good for making things look neat and professional. Thankx for the video BTW
Смешное видео, из темы «мы познаем мир». Что в России уже давно, у них это Must Have
Imagine how great your country could be if it went metric.
It has in automotive. What else would improve if it "went metric" and why?
Tim I hate your videos!!!! Why you ask??? Because every time I watch your videos I say to myself that could come in handy and end up buying more tools. I need help seriously
So sorry that we're adding peer pressure to your tool problem. lol. Thanks for watching.
I must confess - I must have misread the title of this video. I thought it said something about "must have tools" or 'tools you need!!" But here I am, 15 minutes in to this video and not only are these tools completely unnecessary, they aren't things that any normal person would think thinking about. Complete trash. As an ACTUAL MECHANIC (like I actually touch cars n stuff) absolutely not once have I ever thought to myself, "hmmmmm I could really crime some wires or get after that electrical system." Man I normally like this channel but this is pure clickbait for the computer crowd. These aren't tools, nobody has ever actually thought about wires and crimps and electrical toy boxes. Awful video - biggest waste of time I've experienced in years
Stop fuckin yelling at me.
Buncha BS
Junk 😂😂😂😂
Please delete this video
1:30.. where is the link to these large lugs ?