Ive got the Gorilla mmtw board in my article 1 and it feels like a new replica. The semi response is so dmn good and with the app easy to set up with different setups where you also can save and change them. Feels now like a jack. Ive got a festo 90 degree adapter in mine because of the bending problem. now I have 100Percent air trough my line. now with this mod and the silent Industries nozzle I only need 85/90 PSI with .25 BBS to hit 1J before I needen arround 115 / 120 PSI
Dang I'm glad I'm not the only one having low FPS issues with my article 1. I was also getting 280-290 fps with .25s at like 130-140 PSI. Are there any upgrades you made to the hop up/inner barrel/bucking? Both my article 1 and 2 suffer from pretty bad accuracy for guns that cost 1000 USD.
Which hop up rubber are you using with the SI hop unit? I couldn't get it to perform well when I tried it a while ago in combination with an Edgi inner barrel (also running around 1J with 0.25s)
@@timelapses8315 I am using the factory hop up unit and I've tried: I've tried ranges from 50 degree hop up hardness to 80 degree. Maple leaf 2018 macaron Maple leaf 2014 macaron Maple leaf super silicon r hop Maple leaf super silicon macaron Modify flat hop I don't know what works best. I have also tried the omega nub from mable leaf which I believe slightly helped.
@@HikaruSwift17 I tried a bunch too and went back to the regular macaron (60 degrees i think) and the stock hop and barrel. I tried the omega nub too but it overhopped 0.25s for me. I want to try the SI hop again some time. We have two (stock) article ones and accuracy is quite good, i use bioshot 0.25 BBs. I do struggle to get high fps (over 320 fps with 0.25s) but the fields i play at have low limits so it's not a big issue. The inner barrel is quite short, longer one should give more fps (but will stick out).
@@timelapses8315 Well I just got a 30 fps boost by trimming my HPA line and reinserting the screw. Turns out I had leaking because of bending it to much (bending it too often/roughly causes the rubber to widen and get looser). My article 1 with the 8 inch barrel was shooting 280fps, and now its shooting 310 without any hop on .25g bbs. I recommend doing the airseal test in water and see if you get bubbles anywhere. My line wasn't leaking until I bent it alittle to imitate the line being inside the grip, and lo and behold there were some bubbles coming out. Very interesting you are getting overhop with omega nub, it tends to apply less hop than the stock cylinder nub for me since it is shaped for the bbs.
Yo that red dot would look really dope with a unity riser all in all good build makes me want to make one now and I just built a backdraft innovations build 😅
I saw that and another friend has one I'd probably have to convert my foldable stock back to a reg buffer tube. Also I prefer line of the airline system so I don't have to deal with possible leaks Battery grip looks awesome though. Maybe one day I'll try out that combo
@ ahhh yeah may not be able to keep that foldable stock. I think if you put the battery grip in as well you wouldn’t be able to run the airline through the grip. In that case the way you have it is probably best
The Heretic Labs Article 1 SpeedQB edition seems to be sold out everywhere I look for it on the internet, anyone has a suggestion on where I can currently purchase one please?
@@thefastgab the only difference is that the speedqb edition come with "tank grip" or esg style grip for speedsoft The original article 1 just comes with a line You can purchase the esg style grip separately if you wanted to try that out. Otherwise they're both basically the same. You're paying a bit more with the speedqb edition just for the grip and collab between sqb and wolverine
Ive got the Gorilla mmtw board in my article 1 and it feels like a new replica. The semi response is so dmn good and with the app easy to set up with different setups where you also can save and change them. Feels now like a jack. Ive got a festo 90 degree adapter in mine because of the bending problem. now I have 100Percent air trough my line. now with this mod and the silent Industries nozzle I only need 85/90 PSI with .25 BBS to hit 1J before I needen arround 115 / 120 PSI
Keep up with the good work love the content 🎉
Thank you bro
Beautiful build!! What size is that outer barrel?? 7:09
Can't wait to see it in action! Now... stick a Capa in a carbine kit and we're talking 😜
LOL
Can you add a link for the Mac Customs handguard?
I need a part list for one of these
Dang I'm glad I'm not the only one having low FPS issues with my article 1. I was also getting 280-290 fps with .25s at like 130-140 PSI. Are there any upgrades you made to the hop up/inner barrel/bucking? Both my article 1 and 2 suffer from pretty bad accuracy for guns that cost 1000 USD.
Which hop up rubber are you using with the SI hop unit? I couldn't get it to perform well when I tried it a while ago in combination with an Edgi inner barrel (also running around 1J with 0.25s)
@@timelapses8315 I am using the factory hop up unit and I've tried:
I've tried ranges from 50 degree hop up hardness to 80 degree.
Maple leaf 2018 macaron
Maple leaf 2014 macaron
Maple leaf super silicon r hop
Maple leaf super silicon macaron
Modify flat hop
I don't know what works best. I have also tried the omega nub from mable leaf which I believe slightly helped.
@@HikaruSwift17 I tried a bunch too and went back to the regular macaron (60 degrees i think) and the stock hop and barrel. I tried the omega nub too but it overhopped 0.25s for me. I want to try the SI hop again some time. We have two (stock) article ones and accuracy is quite good, i use bioshot 0.25 BBs. I do struggle to get high fps (over 320 fps with 0.25s) but the fields i play at have low limits so it's not a big issue. The inner barrel is quite short, longer one should give more fps (but will stick out).
@@timelapses8315 Well I just got a 30 fps boost by trimming my HPA line and reinserting the screw. Turns out I had leaking because of bending it to much (bending it too often/roughly causes the rubber to widen and get looser). My article 1 with the 8 inch barrel was shooting 280fps, and now its shooting 310 without any hop on .25g bbs. I recommend doing the airseal test in water and see if you get bubbles anywhere. My line wasn't leaking until I bent it alittle to imitate the line being inside the grip, and lo and behold there were some bubbles coming out.
Very interesting you are getting overhop with omega nub, it tends to apply less hop than the stock cylinder nub for me since it is shaped for the bbs.
@@HikaruSwift17 ah good tip! I'll check that. Perhaps I should give the omega nub another try in the stock hop unit.
I just built a gun following your instructions! I’ll see you at CQB city!!!
Yo that red dot would look really dope with a unity riser all in all good build makes me want to make one now and I just built a backdraft innovations build 😅
What modification exactly did you do with your line bro? As I some times have the low fps issue
where'd you get that end attachment to be able to just slide the stock on????
For that price any issues out of the box is inexcusable
no
How is the engine vs jack ?
Does that optic handle BB hits ok?
Do you run your arc or regular esg more? I’m trying to pick between them
🤤 lovely build
Would the esg style grip work on a normal m4?
No, i tried this and it did not it’s meant for the Wolverine Mtw m4 only
Bro why don’t you try the FRAC airline system wolverine has and then the battery grip
I saw that and another friend has one
I'd probably have to convert my foldable stock back to a reg buffer tube. Also I prefer line of the airline system so I don't have to deal with possible leaks
Battery grip looks awesome though. Maybe one day I'll try out that combo
@ ahhh yeah may not be able to keep that foldable stock. I think if you put the battery grip in as well you wouldn’t be able to run the airline through the grip. In that case the way you have it is probably best
The M13 is actually the Sig MCX in real life
Nice!
Very nice
The Heretic Labs Article 1 SpeedQB edition seems to be sold out everywhere I look for it on the internet, anyone has a suggestion on where I can currently purchase one please?
@@thefastgab are you looking for the speedqb edition specifically or just an article 1?
@@iiAnferny is there a big difference in bettween the 2 of them? what do you suggest?
@@thefastgab the only difference is that the speedqb edition come with "tank grip" or esg style grip for speedsoft
The original article 1 just comes with a line
You can purchase the esg style grip separately if you wanted to try that out.
Otherwise they're both basically the same. You're paying a bit more with the speedqb edition just for the grip and collab between sqb and wolverine
Looking forward to your next video about how the beauty works in a skirmish🤩
Not bad
Just cut the line slightly shorter from the quick release regular end. It looks too long
800 dollars very affordable
😂
first
3rd