Soldering techniques

แชร์
ฝัง
  • เผยแพร่เมื่อ 10 เม.ย. 2020
  • For a scripted, and more concise video on soldering techniques, please check out my Beginner's Guide to Surface Mount Soldering Video here:
    • Beginner's Guide to So...
    In this live video I'll be going over the soldering equipment I use and demonstrating some of the techniques I use for soldering different types of components.
    Had I known this livestream would get so many views, I probably would of cut down on the jibber jabber.
    #soldering #electronics #tutorial
    T-SHIRTS
    Do you like my wacky t-shirts? I buy all of them from Qwertee. Use the discount code: BranchusCreations to get £1/€1/$1 off your order. Check out the range here:
    bit.ly/3OrJZkT
    If you enjoy the content and would like to support the channel, please consider becoming a Patron:
    / branchuscreations
    Of if would like to make a small donation, you can do so here:
    www.paypal.me/branchus
    Tools/Products used (paid links):
    SOLDERING IRON
    Hakko FX951: amzn.to/31QvCMW
    SOLDERING IRON TIPS:
    Bevelled edge soldering iron tip (T12-BC2): amzn.to/45NSrBK
    Small bevelled soldering iron tip (T12-C1): amzn.to/3YVH5K0
    Bent conical soldering iron tip (T12-JL02): amzn.to/3sx8lSU
    Chiselled soldering iron tip (T12-KU): amzn.to/44tAo2A
    HOT AIR STATION:
    Quick 861DW: amzn.to/2ZjYzPH
    SOLDER:
    Kester 63/37 0.5mm diameter: amzn.to/3uviEIg
    FLUX:
    StirriASM: amzn.to/43nT05e
    SOLDER WICK:
    Goot Wick 2mm: amzn.to/3YWlRvw
    TWEEZERS:
    Hakko CHP 3-SA: amzn.to/2NqkhPz
    DT71 DIGITAL MULTIMETER TWEEZERS:
    amzn.to/41VcvSb
    OTHER:
    Vevor 30L Ultrasonic Cleaner (5% off on all Vevor sites code: VVMH5%OFF):
    AU site: s.vevor.com/bfP7q7
    US site: s.vevor.com/bfP7uN
    EU site: s.vevor.com/bfQaMb
    -----------------------------------------------------
    Component suction tool (vacuum pen): amzn.to/44xyPkm
    Microscope: amzn.to/2HnSI5H
    Microscope camera: amzn.to/2TdSYsZ
    Budget alternative microscope: amzn.to/2PmRagt
    Budget alternative soldering station (uses T12 tips): amzn.to/2SeUpHg
    Budget alternative hot air rework: amzn.to/3fN1ZU7
    Helping hands (third hand): amzn.to/31JUhVL
    Ultrasonic cleaning fluid: amzn.to/2YusoQQ
    Fume extractor: amzn.to/2HuG0oU
    UV Solder mask: amzn.to/2ZnK1yu
    Swann Morton curved scalpel blades: amzn.to/2oN7qNn
    No. 3 Scalpel Handle: amzn.to/2ngcx85
    Kapton heat resistant tape: amzn.to/2xBnTso
    28 AWG enamelled magnet wire (thick): amzn.to/32cRsLf
    34 AWG enamelled magnet wire (med): amzn.to/35Bx20D
    40 AWG enamelled magnet wire (thin): amzn.to/2J2Aisf
  • วิทยาศาสตร์และเทคโนโลยี

ความคิดเห็น • 157

  • @Felipera_
    @Felipera_ 3 ปีที่แล้ว +42

    This vídeo is proof that we need to learn from technicians that also post on TH-cam instead of TH-camrs that pretend to be technicians. The difference is that you can easily talk for 2 hours with no time wasted in fluff, Just straight up info, as oposed to stretching 2 minutes worth of content into 10 minutes for the algorithm.

    • @mattsterxx4040
      @mattsterxx4040 2 ปีที่แล้ว

      Whats the algorithm? (In 2 minutes or less)

  • @BoydFlowers
    @BoydFlowers 2 หลายเดือนก่อน +3

    I’m new soldier thank you so much 🎉

  • @Benniebe
    @Benniebe หลายเดือนก่อน +1

    I learned a lot from this video. Thank you.

  • @ajurch9992
    @ajurch9992 4 หลายเดือนก่อน +1

    Since leaving my job ive got into doing electronics and repairing things, im at the soldering stage now, so very informative for me. Thankyou

  • @saidbaci4344
    @saidbaci4344 ปีที่แล้ว +4

    Thanks for sharing your precious experience about soldering. Soldering seen from outside looks like a child game: Just get the hot soldering iron close to the electronic component and the trick is done. But as a matter of fact, that's not that obvious, particularly when micro-soldering is concerned. It's very well appreciated. Cheers.

  • @TarxnG
    @TarxnG 2 หลายเดือนก่อน +2

    Bravo Partner, bravo. Cheers from Texas

  • @Miamiyatusabes
    @Miamiyatusabes 9 หลายเดือนก่อน +2

    Bless Up Brother 🙌 MUCH Thanks Batman

  • @Sir.RickParker949
    @Sir.RickParker949 ปีที่แล้ว +6

    Brian;I'm so glad I found your instruction videos,and I'm looking forward to seeing all of them. So far I've watched pt.1&2 of basic soldering and a few others.
    I was a auto mechanic but now I'm pursing electronics since I've always understood electrical theory
    I have a strong desire to fix and design. Thank you so much my friend.

  • @BhekizithaMoyo
    @BhekizithaMoyo 6 หลายเดือนก่อน +2

    Very nice and good teacher

  • @stew.c
    @stew.c 7 หลายเดือนก่อน +1

    An old video, but so insightful! Thank you…

  • @TheAMGReviewers
    @TheAMGReviewers 5 หลายเดือนก่อน +1

    Knowing you from future videos then seeing...this start...what a shocker 😂 GG WP

  • @gabrielgaby5840
    @gabrielgaby5840 8 หลายเดือนก่อน +1

    Thanks for a good evening on this subject... 😂get some sleep, ready for the next session...

  • @MikaelXJohansson
    @MikaelXJohansson 6 หลายเดือนก่อน +1

    15 viewers live to over 137k views 3 years later! Big congrats on that and thanks for the content!

    • @BranchusCreations
      @BranchusCreations  6 หลายเดือนก่อน +5

      Thank you! The success of this video was very unexpected. Maybe it was the Batman mask?

  • @xnlpLUKAS
    @xnlpLUKAS 4 ปีที่แล้ว +12

    Your kind of "hovering" technique while applying flux onto the smd pads and then appling solder onto all of the pads in a row at once in such a quick and easy way is something i never saw before. Thanks for showing us your experience and sharing your knowledge with us. I like your explanation videos very much because you are very charismatic and explain your technique by showing us various examples where you get straight to the point and even give us some recommendations and tips along the way. Thank you very much! :)

  • @timdailey2690
    @timdailey2690 ปีที่แล้ว +1

    Holy Masterclass, Batman!!
    Thank you Bruce! Your videos are a real education.

  • @helenajokic5693
    @helenajokic5693 ปีที่แล้ว +2

    Thank you for you in depth instruction , covering the basics for a beginner like me. Thank you One Ozie to another.

  • @ellisbaudean8861
    @ellisbaudean8861 ปีที่แล้ว +1

    U have been a Blessing I,ve learned from watching u , now I'm sordering on motherboards LED lights you name it I love to sort I'm good at it thank you

  • @greenbears1382
    @greenbears1382 ปีที่แล้ว +2

    If I had you as a teacher in school !! Great job !!

  • @ForestWoodworks
    @ForestWoodworks 2 ปีที่แล้ว +5

    True story! I was literally shooting content for my own channel when the ac jack on my laptop decided to break, the rest of the way. Lost all that footage, but what I did find was this AWESOME channel. I finally got the old jack removed, and I feel much more confident that I'll be able to solder on the new one when it arrives, hopefully tomorrow. Thanks man, I appreciate the great tutorials!

  • @treadmillrepair754
    @treadmillrepair754 2 ปีที่แล้ว +1

    This is the real Solder Mask.
    Best Regards.

  • @paul3461
    @paul3461 6 หลายเดือนก่อน +1

    Helllllóoóoo first timer and going for the longest running watcher I took basic electrical in high school I was there for 1 month and then I came back 3 months later and the teacher asked who I was I said that I went for lunch at the pub a half block away and got lost I did injoy it but I was not allowed back one thing I did learn was that LED lights were going to be in the future but it would take a long time for people to accept them that was back in 1986 I also learned how to make a circuit board I have forgotten that and now I have an idea for a project and I need to make a small circuit board I'm very happy to have found your site

  • @wildcat189
    @wildcat189 10 หลายเดือนก่อน +1

    This was amazing to watch.

  • @bshirl21
    @bshirl21 ปีที่แล้ว +1

    Thank you for your time and knowledge. I've been taking this info in like Neo in the Matrix.

  • @billcarson9565
    @billcarson9565 3 ปีที่แล้ว +1

    Extremely boring??? not a chance Sir! I have learned so much watching your vids! subscribed!

  • @tvsgod
    @tvsgod ปีที่แล้ว +4

    You are genually a great teacher and person , hopefully you will do another stream , the one that you mentioned at the end with newer motherboards and repairing them soon . I'd personally like to see tearing a cpu or an integrated video chip . Greetings !

  • @mac_music511
    @mac_music511 ปีที่แล้ว +2

    massive amount of wisdom and experience in this. Thank you very much!

  • @denis7868
    @denis7868 3 ปีที่แล้ว +1

    Hi there from Brisbane- great site. I am starting to get into guitar pedal building. It is a sharp learning curve- but your advice is priceless- thank you so much.

  • @deadpersimmon
    @deadpersimmon 3 ปีที่แล้ว +1

    Thanks for a great video, very educational. Trying to learn soldering, very helpful.

  • @stevenwidener5199
    @stevenwidener5199 3 ปีที่แล้ว +1

    very informative taught me alot especially where i was making mistakes

  • @Dzmaestro
    @Dzmaestro 3 ปีที่แล้ว +5

    Loving the super informative video! And that 2hrs felt very much like a 20min video. I'm trying to learn soldering and has close to zero experience doing it. Your videos has definitely pique my interest and hope that it'll be a new found hobby that i could do mini projects out of it. Looking forward to more of your soldering/electrical videos!

    • @lilslump1121
      @lilslump1121 11 หลายเดือนก่อน +2

      We need an update !

  • @Liveitlarge247
    @Liveitlarge247 2 ปีที่แล้ว +1

    Excellent stuff!

  • @AlbertoManantan-wf3dl
    @AlbertoManantan-wf3dl 9 หลายเดือนก่อน +2

    Hello from Santa Maria California

  • @JervaughnLewisRio
    @JervaughnLewisRio 3 ปีที่แล้ว +1

    Great Vid, keep doing them.

  • @camerong5349
    @camerong5349 หลายเดือนก่อน

    Thank you!

  • @davehall373
    @davehall373 หลายเดือนก่อน +1

    Thanks

  • @krumbleme2
    @krumbleme2 10 หลายเดือนก่อน

    @Branchus Creations what is the purpose of mixing solder with your flux as conpared to just using the flux and copper wire to clean the plates?
    I'm working on a project for the first time and would appreciate your feedback. Thanks

  • @eamoinnmckinley3755
    @eamoinnmckinley3755 2 ปีที่แล้ว

    Very informative, thank you.

  • @jmbmwmiami
    @jmbmwmiami หลายเดือนก่อน

    Hello Sir, I would like a recommendation for a good microscope, what characteristics should it have?

  • @greyhnd001
    @greyhnd001 3 ปีที่แล้ว

    I have a pin missing on my arduino uno 328p. I had to remove it to use it as a programmer and when I went to put it back in I broke one of the pins. I havent figured out what it is attached to but I did have an issue programing my attiny85 with my uno and switched to programing it with my arduino nano.

  • @rigoleyja4043
    @rigoleyja4043 3 ปีที่แล้ว

    Im trying to learn how to repair ic chips for iphones. I can remove the ic chip with heat gun. When i go to clean the board with the solder gun i end up removing too many pads and i cant get the solder to stick to the tip? For flux i use RMA-223 volume 10cc on the solder wire 0.08 grade YF-11. What am i doing wrong?

  • @daz41262010
    @daz41262010 ปีที่แล้ว

    love the batman cowl :) you looked awesome :) and I was thinking this exact thing when I heard your name for the first time :) well done Bruce great fun to watch :)

  • @mattsterxx4040
    @mattsterxx4040 2 ปีที่แล้ว

    Do you cover plastic welding as well? I'd like to see one of those in action (by you). thanks....

  • @bneexotics2120
    @bneexotics2120 3 ปีที่แล้ว +2

    Really enjoyed the video 👍 Im a fellow Aussie and complete beginner, found your channel while searching for tips to get started. Went back through your catalogue and found your video for beginners which was exactly what I was looking for.
    Thankyou for the tips your delivery of information is spot on and I've subscribed to the channel, I will be watching all the videos over the coming weeks. Some advice on what iron to pick up to get started would be much appreciated and what websites you recommend to buy from would great. Thanks again mate 👍

    • @ajurch9992
      @ajurch9992 4 หลายเดือนก่อน

      same.

  • @tikonc
    @tikonc 2 ปีที่แล้ว

    I haven't heard you mention in any of your soldering videos about tinning the tip before using it....is it something to be done or not? Nice videos

  • @jaycarruthers4089
    @jaycarruthers4089 ปีที่แล้ว

    I’ve a precision gold a55kj and my tip doesn’t seem to get hot I can see the glowing core but alas not enough heat. Any ideas? Tip may not be from the right iron??

  • @ntulsian
    @ntulsian 6 หลายเดือนก่อน

    I am trying to find the temp used for the hot air, when removing components.
    I have a hot air station and tried using it around 380⁰C but the solder wouldnt soften, so i ended up using the iron at about 350 and rhat worked just fine.

  • @daisukiyamamoto3904
    @daisukiyamamoto3904 10 วันที่ผ่านมา

    Beautiful job, where are you located?

  • @asfilmproduction1433
    @asfilmproduction1433 3 ปีที่แล้ว

    Great work sir thanks.

  • @jaumantu5947
    @jaumantu5947 ปีที่แล้ว

    Thx for tips and yes very well mate 👍👏👌

  • @Bill224ful
    @Bill224ful 3 ปีที่แล้ว

    at 1:08:52 you talked about the flux. I just picked up(before watching this video) some Rosin Flux Paste by Thermaltronics. It says its good for electronics. I just wanted to know what you would have to say about it. Its a completely different color than the Flux you show not use in the video. Also great video/stream

  • @RaffaelloLorenzusSayde
    @RaffaelloLorenzusSayde 3 หลายเดือนก่อน

    How do you fix an accidentally loose or removed metal pad? Also, how to solder two wires together without melting the plastic coating?
    Thanks, mate 👏

  • @codydowling1120
    @codydowling1120 3 ปีที่แล้ว +1

    Great work! I noticed your a fan of the gel flux as well- out of curiosity, what flux remover do you like?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +2

      I use either isopropyl alcohol or MG Chemicals flux remover for spot cleaning. If the board is completely covered in flux after doing major repairs, I use an ultrasonic cleaner with a solution specially designed for cleaning electronics.

    • @codydowling1120
      @codydowling1120 3 ปีที่แล้ว +1

      Branchus Creations Sounds like we have similar taste in flex remover too! 😊
      I do not, however, have “... an ultrasonic cleaner with a solution specifically designed for cleaning electronics” and I’ll admit that I am a bit jealous. 😜

  • @orrendous
    @orrendous ปีที่แล้ว

    Why do you recommend not using rosin Flux? What does it do to electronics that you don't like?

  • @kurohyuki5912
    @kurohyuki5912 3 ปีที่แล้ว +4

    that key is for factory uses i think. they lock the temperature workers use so they always follow production standards

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +3

      That was my assumption, but it still seems a bit mean.

  • @diskdoctorprague
    @diskdoctorprague 3 ปีที่แล้ว +1

    Nice tipps - thanks for that but I have a question. What do you think about using a T862++ / IR6500 / IR8500 or some other IR rework station? They should be even better working for chips like that.

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว

      For sure, those machines are great for BGA rework, but they cost a bit. I'll probably get one someday.

    • @diskdoctorprague
      @diskdoctorprague 3 ปีที่แล้ว

      @@BranchusCreations A T862++ cost less then 200 USD when you import it directly from China. I have one and I really like that I can pick up the chips very easy and solder them back directly with the old solder. I use that often for ROM-transfer when I do a PCB swap on a HDD.

  • @donbennett2788
    @donbennett2788 ปีที่แล้ว

    I have a 95 corvette with ecm in need of a reflow on ecm. This is something new to me and to top it off board has rubbery conformal coating and the ecm is made of unobtainium. I know it can be saved because it works intermittently. Any knowledge shared will be greatly appreciated

  • @cbmeeks
    @cbmeeks 2 ปีที่แล้ว +3

    Batman's soldering system costs $40M and are implants in his eyes.

  • @63Arnast
    @63Arnast 3 ปีที่แล้ว +1

    Nice video.. how do you get rid of the green stuff on top of the traces/tracks and how can you repair broken ones?

    • @Dr.Peppermintz
      @Dr.Peppermintz 2 ปีที่แล้ว

      I know this is late, but hes reviewed this recently. Basically he scrapes it off with a blade and then uses flux (Lots and lots of it), as well as solder and new copper to repair the traces.

  • @jaumantu5947
    @jaumantu5947 ปีที่แล้ว

    You have to love Bruce Wayne very good strategy by the way, I don't celebrate Christmas but Mary soldering techniques it shall be, thanks

  • @dertyberty
    @dertyberty 3 ปีที่แล้ว

    thank you brilliant really enjoyed the lessons the greatest thing is to know
    . ps i found your volume level to be a bit low.i suppose it made me listen more keenly.

  • @henryyang3695
    @henryyang3695 3 ปีที่แล้ว

    can someone tell me , why at 1:04:04 to make solder nice first if need to remove them later???

  • @interviewswithiconsandsome6721
    @interviewswithiconsandsome6721 2 ปีที่แล้ว

    Hello sir, can you please offer a little guidance on how I might fix this? My dog chewed it.
    Thank u!

  • @raymondholt4771
    @raymondholt4771 ปีที่แล้ว

    Great videos

  • @bryandamage4007
    @bryandamage4007 3 ปีที่แล้ว +1

    I just ripped two fat dabs of cherry pie live resin, and I'm loving this. Man, I used to think I was hot shit installing mod chips into the original xbox consoles for friends. Some of the motherboards came with two empty spots where 2x32mb ram could be soldered, but I never had the balls to attempt that shit. Anyway, thanks for the entertaining stream, bro.

    • @Wally17.
      @Wally17. 3 ปีที่แล้ว

      The 128mb RAM mod is something I definitely want to try doing. Nice to see another fan of the original Xbox. Have you seen the recent XboxHDMI mod by MakeMHz? The install on that almost looks easier than the RAM upgrade.

  • @jaumantu5947
    @jaumantu5947 ปีที่แล้ว

    Say is there any way you could show me how to fix the power plug to a speaker?

  • @Sisko125
    @Sisko125 3 ปีที่แล้ว

    Hi there and great video!!! Could you do one on hot air work station please!! Thanks!!

  • @seattledanr5363
    @seattledanr5363 ปีที่แล้ว

    Great video, Bruce. Thanks! I was wondering why my solder connections were SO DANG CRAPPY. Now I know. Flux. Lots of it. Judging from this video, I will seek a 1 liter tube of the stuff. ;-) Oh, and I'm using one of those fine-point conical tips. Getting a couple thicker flat and wedge tips, too. The pins on those components were pretty large (2-3mm spacing). Do you ever work with really small pin components? Things like a USB-C or USB-micro adapter, where pins are 1mm apart. Same process? Flux, drag solder... Different tip? I can't imagine using that fat tip on such small components. Thanks again!

  • @jedininja83
    @jedininja83 2 ปีที่แล้ว

    Can anyone please tell me where I could get a soldering station that I can change the tips even if it's hot

  • @Johadart
    @Johadart 2 ปีที่แล้ว

    Hey buddy, great learning technique, so happy to have watched this video, I’ve subscribed to your awesome channel.. Keep up the great work…
    P.S 450* Celsius = 842* Fahrenheit
    From a fellow Aussie 🤙🏼🤙🏼🇦🇺🇦🇺🤙🏼🤙🏼

  • @DynoDieselWagon
    @DynoDieselWagon 2 ปีที่แล้ว

    Well done

  • @RobstaHendricks
    @RobstaHendricks 3 ปีที่แล้ว

    Yea, that interface looks a bit silly, and the key thing too, but the colour branding kinda makes sense when you've got hot stuff around to be bright...
    I've got an Hakko FX901 as my portable one that's a 4 AA job (400°C with NiMH rechargeables and apparently 600°C Alkaline!!), which whilst I'm careful, (and the cleverly designed cap witches the power off) I kinda like the bright colours for safety...
    My base station, well, I'm not so concerned because you usually put it back home between solders....
    Great video though. Thank you :)

  • @alanwong3980
    @alanwong3980 3 ปีที่แล้ว +1

    Hi Batman, I see you replacing round shape capacitors with the rectangle shape one.
    I am trying to recap my camcorder. it's full of the round sharp surface mount cap.
    Should I replace them with rectangle?
    Please advise

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว

      In the video I am replacing surface mount electrolytic capacitors (round ones) with tantalum capacitors (square ones). There are a range of reasons why I do this, but if you're not sure about what to use, it's probably just safer to replace with the same kind.

    • @alanwong3980
      @alanwong3980 3 ปีที่แล้ว

      @@BranchusCreations Thanks for your reply. Could you demonstrate how to replace the surface mount electrolytic capacitors (round ones), please?

    • @alanwong3980
      @alanwong3980 3 ปีที่แล้ว

      Using the same way to replace them?

  • @alanwong3980
    @alanwong3980 3 ปีที่แล้ว +1

    Hi Batman, What temperature should I use the clean the pad?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +1

      That really depends. I use a very high temperature (430ºC), but I wouldn't recommend that for beginners. If you're using leaded solder, try somewhere around 350ºC.

    • @alanwong3980
      @alanwong3980 3 ปีที่แล้ว +1

      @@BranchusCreations thanks Batman. btw I like the batman mask.

    • @mohandmohand2047
      @mohandmohand2047 2 ปีที่แล้ว

      @@BranchusCreations 430 about how much time!!? Is it safe temperature bro. You say lead iron?!?

  • @ZsoltPal23092011
    @ZsoltPal23092011 3 ปีที่แล้ว

    excellent vid, thanks!
    at 1:01:20 "and you got led on your hand, so you should be wearing gloves exactly like I'm not" :-D
    the good ol' prinicple - do as I say, not as I do

  • @alanamos5158
    @alanamos5158 3 ปีที่แล้ว

    I just bought 5 different things from amazon and been watching your videos to learn. Im a landlord just trying to learn new things, so I invested 115.00 for a soldering and disoldering combo station, flux, and 3 more things to start. I was wondering if the solder is worth anything that I get from the disoldering. I have alot of boards with gold and etc. Can you give me any kind of suggestions..And I have subscribed

    • @hantusangap
      @hantusangap 3 ปีที่แล้ว

      buy hakko fx951.dont buy 3 in 1 rework station such saike auyoe etc that just kind a shit.buy that and u will end up buying another after 3 month

  • @drjayem1971
    @drjayem1971 3 ปีที่แล้ว

    Love the video. But where did yoy get that mask. I want one!

  • @jhellvie
    @jhellvie 3 ปีที่แล้ว

    It's works...nice

  • @anthonytremblett8187
    @anthonytremblett8187 3 ปีที่แล้ว +1

    Just had ago at trying to install a Jimmy Page wiring harness in my Les Paul Standard and umm yah, wish I could hand it over to someone like you. Let's say, there's a few issues. Gonna have another go..I think or find someone to pay, ha.

  • @virendrapratap512
    @virendrapratap512 2 ปีที่แล้ว

    Sir give me solution on printing machine byhx & umc board

  • @cuyaclint9247
    @cuyaclint9247 ปีที่แล้ว

    new subscriber here from the Philippines. Hope you will notice.

  • @fabrziodelfabbro5802
    @fabrziodelfabbro5802 3 ปีที่แล้ว +1

    Thank you

  • @PaOutcast
    @PaOutcast 3 ปีที่แล้ว

    I'm here to learn

  • @MisterXS75
    @MisterXS75 3 ปีที่แล้ว +1

    why do you have capton tape on your scope camera?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +1

      The camera is just a bit too loose in the holder, so I use tape to hold it still. Why kapton? That's what I had nearby.

  • @FishinBob
    @FishinBob 3 ปีที่แล้ว +1

    Bruce. Why didn't you open up the broken station and redo the board?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +1

      It's a while since I recorded this. Which station?

    • @FishinBob
      @FishinBob 3 ปีที่แล้ว +1

      @@BranchusCreations it was just an old soldering station that you were showing on one of your basic soldering courses.

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว

      @Fishin Bob I'm pretty sure it still works!

  • @TheDynomike100
    @TheDynomike100 3 ปีที่แล้ว

    Can u fix my gaming laptop motherboard trace

  • @user-ie6oy5jj4y
    @user-ie6oy5jj4y 6 หลายเดือนก่อน

    Check for cigarettes smoke as cause fir dluff and cloudingbup scope

  • @ugamer6581
    @ugamer6581 9 หลายเดือนก่อน

    Mr. Batman telling us- Get ready to learn how to soldering.👈☝👌💪✌👍😅😎🤑😋😋😆😋❤❤❤❤❤❤❤

  • @russellesimonetta3835
    @russellesimonetta3835 ปีที่แล้ว

    I'm American and I sodder (solder) with a weller.

  • @marinehm
    @marinehm 3 ปีที่แล้ว +5

    Hahaha The mask. What the hell?!!! Great video

  • @jeisonsanchez4842
    @jeisonsanchez4842 2 ปีที่แล้ว

    I knew it! You ARE Batman!

  • @FishinBob
    @FishinBob 3 ปีที่แล้ว

    Is alcohol better than acetone?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +2

      Fishin Bob Acetone can do some terrible things to plastic, so I wouldn't recommend it.

    • @FishinBob
      @FishinBob 3 ปีที่แล้ว

      @@BranchusCreations Thanks. I 'd thought that. I've moved on to 70% Isopropyl while looking for some 99% Great video.

  • @gabrielgaby5840
    @gabrielgaby5840 8 หลายเดือนก่อน

    Naughty... breaking pins.... ...what if it now not work...😮

  • @user-kr5ry2ft8s
    @user-kr5ry2ft8s 2 ปีที่แล้ว

    Вы так быстро говорите, что я не успеваю прочитать перевод)))

  • @jeffjorczak
    @jeffjorczak 3 ปีที่แล้ว +1

    Very helpful video. I am curious why you are repairing 30 year old computers?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +1

      It's sort of become my niche repair business. Lots of people are getting their vintage computers restored so that they can enjoy old apps and games they played when they were younger.

    • @italianbasegard
      @italianbasegard 3 ปีที่แล้ว +1

      Jeff - Do a quick eBay search for "1984 Mac" and you'll see there's definitely a market for repair work like this. Highly doubtful that you can walk into an Apple store with a 36 year old Macintosh and they'd be willing to repair it, so we must learn for ourselves!

    • @jeffjorczak
      @jeffjorczak 3 ปีที่แล้ว +1

      @@italianbasegard I guess my question is why you would want to use a machine that old.if it's for nostalgia there are emulators.

    • @italianbasegard
      @italianbasegard 3 ปีที่แล้ว +2

      @@jeffjorczak Why do cities mark areas as "Historical Districts"? Why do we try to preserve the pyramids instead of tearing them down? It's to preserve history.
      Also, idk if you've ever tried to play a playstation game on a playstation emulator (any other emulator seems to work fine instead of PS1) but the experience is terrible and nothing like the original. Sometimes it's more functional to go with original hardware.

    • @Wally17.
      @Wally17. 3 ปีที่แล้ว

      @@italianbasegard Exactly. On the note of PS1 emulation, it’s kind of the same with the original Xbox. Except, there’s not a good emulator for it really at all almost 20 years after it’s release. The only way to experience a lot of the games is on the console and a lot of them nowadays are starting to need repairs.

  • @jocktigernuts680
    @jocktigernuts680 2 หลายเดือนก่อน +1

    There are some sick people out there😱

  • @jamesmays6826
    @jamesmays6826 3 ปีที่แล้ว

    The key is for industrial use fill the employee cannot change the temperature

  • @bonnieanderson5865
    @bonnieanderson5865 3 ปีที่แล้ว +3

    Hello, I am trying to repair my carpet cleaner cord that my dog chewed through.

    • @williambeltran5105
      @williambeltran5105 3 ปีที่แล้ว +1

      P]p po⁹⁸⁸⁸⁸⁸⁸⁸⁸⁸ is pl 909990⁰0090 OP 009999999⁹9⁰pip p p.o[o[o[[ooo[[o[oo[[[o[[o[[[[oo[[o[[oio>>>or 9999⁹9⁹⁹999⁹OP⁹⁹⁹⁹⁹⁹ooi 8

  • @jaumantu5947
    @jaumantu5947 ปีที่แล้ว

    You brother

  • @multibusa
    @multibusa 2 ปีที่แล้ว

    Hello from stevo

  • @zarulyakuza
    @zarulyakuza 3 ปีที่แล้ว +1

    wah the batman of return mask?

    • @BranchusCreations
      @BranchusCreations  3 ปีที่แล้ว +1

      My name is Bruce Rayne, and people get me mixed up with Bruce Wayne all the time.