MR JE C Servo ( Home & Positioning) with FX5U Part 2 (CC link IE Field Basic)

CC Link IE Field Network Basic is compatible Servo Amplifier MR-JE-C.
GX-Works 3 Parameter Setting
• Device Numbers Used For Read/Write Function
• Communication Start Setting
• Program Operation Modes - Velocity Mode
Device Numbers used to Write from Master station to servo Amplifier and to
Read from Servo Amplifiers to Master station
------------------------------------------------------------------------------------------------------------------------------------------
Program Sample At:
automationsolutions.tk/
automationsolutionz.blogspot....
Download Sample Section
------------------------------------------------------------------------------------------------------------------------------------------
To operate the amplifier in velocity mode switch amplifier to “Profile
Velocity Mode (pv)”.
• To Switch the amplifier to “Profile Velocity mode (pv)” write value ‘3’
(i.e. K3) to Control word (i.e. RWw00).
• After switching to “Profile Velocity Mode (pv)” write “Target Velocity”
to Speed Command (pv) (i.e. RWw00 + 07).
• While operating the amplifier in “Profile Velocity Mode (pv)”, the “Bit
No. 15” should be on with the start command.
• To start velocity movement write value ‘32895’ (i.e.K32895) in control
command. (i.e. RWw00 + 01).
• Depending on the sign of “Target Velocity” direction of movement will
be decide.
(i.e. Positive velocity Forward-Rotation,
Negative velocity Reverse-Rotation.)

[@chetankatageri5845]

Thankyou for the video. I was having a lot of confusion, but after watching this video all my confusions got cleared......
Thanks alott

[@srinivasangopinath3793]

Thanks a lot for the part2. Most awaited one.

[@user-uh8lo9op4t]

Very very good tech video you Are doing such a wonderful job... thank you so much 🙏

[@jesusaliagapoma2428]

Hello, excellent video, could you explain how it would be the case for an ethertnet communication using an EDS file of the servo drive for any controller. Thank you

[@amitpathak3p825]

Thanks for to shared such valuable information, its help us lot. Can any one let me know how to read actual current (Amp. ) value from servo drive just like we can read from VFD.

[@krishangoyal9739]

Sir once the positioning is done which bit will be high?

[@maheswaran9727]

What are the setting to be done at amplifier side

[@krishangoyal9739]

Sir
How can I reset D1003 ( present position).
I want to get it zero at a specific condition.
Can I do?

[@sheikameer8235]

WHY K31 AND K 95 ARE MOVED TOWARDS CONTROL WORDS

[@hapham-qd4jl]

how to turn SON ON.( Servo ON). Don't use CN3

[@gameshowhot6346]

Do you use the CN3 origin input?

[@Technocrats91]

Parameter PT45 is set 37, which is for Data set homing method,
You can use CN3 Pin No. 2 DOG For other homing methods.

[@Technocrats91]

For more clarification you can refer manual
MR-JE-_C SERVO AMPLIFIER INSTRUCTION MANUAL (PROFILE MODE)

[@gameshowhot6346]

Can you give me gmail, or contact information

[@gameshowhot6346]

If I am not using CN3, what home method do I use.

[@Technocrats91]

[e-mail]

[@SwarajSinghSTC]

Sir please Send link of this User manual

[@davidekadukowski4656]

What are the first 2 lines for?

[@Technocrats91]

To start communication between plc and cc link ie field basic device

[@patelromilnareshbhai]

Can i write more than one point table at one time??

[@Technocrats91]

Yes

[@patelromilnareshbhai]

@@Technocrats91 then sir can you please mail me sample program of it or any video how to write multiple point table at same time
[e-mail]

[@patelromilnareshbhai]

Hello sir will you share any backup or sample for multiple poont table write in single time
[e-mail]

[@Technocrats91]

Sure

[@rojor7458]

Dónde encuentro el documento Acrobat

[@Technocrats91]

From Mitsubishi Site or just type mr je c communication manual in Google

[@muhammadfassil4726]

MR configuration settings for MR- JE -C

[@manorhydraulicsautomation2817]

Sir Contact detail please