ขนาดวิดีโอ: 1280 X 720853 X 480640 X 360
แสดงแผงควบคุมโปรแกรมเล่น
เล่นอัตโนมัติ
เล่นใหม่
Thank you , I will need this video next two days , same problem in my 3CX
I'm learning this for the first time,but I am a mechanic in Light vehicle
Que vídeo bem feito gostei muito
Gostei da manutenção 🤝👏👏👏🇧🇷
Obrigada.
Bravo.maestro
Good video bro
❤😊😊😊
Kedves Laci!Van e olyan Videótok amely a vàltórol szól?Üdvözlettel
You are great
Shir mero ko bhi jcb mecnik ka bija mile ga
Donde comprar repuestos para jcb 3cx modelo 1989
slovakia.hydrob sk.ndstrojov.sk
Very good video, very detailed thank you, little to much silicone doe.Best regards
You should heat bearing before assembly. It will be easier to put it on shaft.
What would you need to heat it with. A hot air gun, in an oven or with a gas flame?
@@ashleysomerville2509 There are several methods. The best solution is to use bearing heater that allows to heat bearing to particular temperature.
how much kg/cm 2 torque
Хоть русский, хоть не русский человек, всё равно всё мажет ПАЛЬЦЕМ, герметик, хоть смазку...
Матерится наверняка так же НО по своему .
Мазать не нужно, кольцо резиновое великолепно держит...
very wonderful
Good working 👍👍👍
Не нужен там герметик. Сальник не стал на место. Пыльника нет(
Bearing size please?
BEARING 907/50000 SEAL DUAL LIP 904/50021 127x160x15,5/17,5 mm O RING 828/00196
@@lacibatoch1673 how much torque
Gud
Adammm
What's bearing type used for replacement?
Ložisko nápravy jcb 907/5000 ARB 37 425.37 625
Oil seal sizes please??
Ковш покрасить не забыл. а нож не поменял(
Nao precisava nem retentor, foi tanto cilicone que isso nao vaza óleo nunca mais kkķkkk
Rumuński Jarek Ogarek pokazuje jak nie naprawiać koparki. Paproch na medal
9:06 Miért nem melegítetted meg egy kicsit a csapágyat és akkor kalapálás nélkül is rá ment volna a tengelyre
Így is könnyen ráment,nincs szoros kötése.
Niestety naprawa źle wykonana, brak osłony przed uszczelniaczem spowoduje dostanie się piachu czy czegokolwiek i wyciek od nowa.
Hammering a dry bearing that a no no You heat up the bearing goes on a lot easier
The seal should be put into the hub not as you have done and also the seal should not be run on top of a coat of paint. Bad practice.
no mécano ... bricoleur 👎🏼😂😂
Thank you , I will need this video next two days , same problem in my 3CX
I'm learning this for the first time,but I am a mechanic in Light vehicle
Que vídeo bem feito gostei muito
Gostei da manutenção 🤝👏👏👏🇧🇷
Obrigada.
Bravo.maestro
Good video bro
❤😊😊😊
Kedves Laci!
Van e olyan Videótok amely a vàltórol szól?
Üdvözlettel
You are great
Shir mero ko bhi jcb mecnik ka bija mile ga
Donde comprar repuestos para jcb 3cx modelo 1989
slovakia.hydrob sk.ndstrojov.sk
Very good video, very detailed thank you, little to much silicone doe.
Best regards
You should heat bearing before assembly. It will be easier to put it on shaft.
What would you need to heat it with. A hot air gun, in an oven or with a gas flame?
@@ashleysomerville2509 There are several methods. The best solution is to use bearing heater that allows to heat bearing to particular temperature.
how much kg/cm 2 torque
Хоть русский, хоть не русский человек, всё равно всё мажет ПАЛЬЦЕМ, герметик, хоть смазку...
Матерится наверняка так же
НО по своему .
Мазать не нужно, кольцо резиновое великолепно держит...
very wonderful
Good working 👍👍👍
Не нужен там герметик. Сальник не стал на место. Пыльника нет(
Bearing size please?
BEARING 907/50000 SEAL DUAL LIP 904/50021 127x160x15,5/17,5 mm O RING 828/00196
@@lacibatoch1673 how much torque
Gud
Adammm
What's bearing type used for replacement?
Ložisko nápravy jcb 907/5000 ARB 37 425.37 625
Oil seal sizes please??
Ковш покрасить не забыл. а нож не поменял(
Nao precisava nem retentor, foi tanto cilicone que isso nao vaza óleo nunca mais kkķkkk
Rumuński Jarek Ogarek pokazuje jak nie naprawiać koparki. Paproch na medal
9:06 Miért nem melegítetted meg egy kicsit a csapágyat és akkor kalapálás nélkül is rá ment volna a tengelyre
Így is könnyen ráment,nincs szoros kötése.
Niestety naprawa źle wykonana, brak osłony przed uszczelniaczem spowoduje dostanie się piachu czy czegokolwiek i wyciek od nowa.
Hammering a dry bearing that a no no You heat up the bearing goes on a lot easier
The seal should be put into the hub not as you have done and also the seal should not be run on top of a coat of paint. Bad practice.
no mécano ... bricoleur 👎🏼😂😂