I liked your observation of the board, it’s a very good tip to look at the grounding connections. Your English although not perfect is understandable, and you can get your thoughts across. If I may present a few ideas, try not to use your soldering iron tip on anything else than the solder, circuit board and component leads. It can get contaminated and prematurely worn, plus it can make your job harder. I always test the iron temperature with the solder itself, once it melts you are in the right ball park temperature wise. It should always be able to hold a small solder bead, if it doesn’t either it needs restoration or replacement. Using flux paste massively helps to melt the solder. The quicker it happens the less heat you will transfer to the board and adjacent components that might be heat sensitive. After soldering, a quick wipe with isopropanol will leave a clean and extremely professional look. I hope you take this as a contribution for other viewers that are getting started in electronic repair, aside from this thank you for sharing this video, it’s great to have people who help others improve their knowledge and skill. Most people get scared getting into circuitry as if it’s something massively difficult. As with everything else, there are some general principles to observe, proper techniques and the rest is practice as much as possible. What you did there helps demystify the black box that people see when they look at an ECU and don’t even dare cracking it open. Those usually just get replaced and they are very pricy, while it can just be a cracked joint or loose connection that any beginner can fix with limited knowledge and means. This is a good step forward, seeing how others have done it and following in their footsteps. Overall, you did a good job, I just wish you would have shown if that repair solved the problem. Well done.
@@PeterFinnTheCarDoctor problem facing in Chevrolet captiva 2007 manual, DTC U0073(Control Module Communication Bus OFF), U0121(ABS MODULE lost communication) and P0500(Vehicle Speed Sensor) ,,,,suddenly instrument cluster stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working, Service Vehicle Soon light & MIL illuminates in cluster. and all happen intermittently and all together but car keep running till next key turn off, however if problem comes in key ignition position then I have to connect-disconnect battery several times then luckily car get started. Can anybody suggest solution?
Peter Finn the Car Doctor hello how are you doing Mr. Peter I have a 2008 Infiniti QX56 Jeep and one day the Jeep started malfunctioning the two side mirrors would open and closed every time the Jeep is started and the reverse cameras would come on when the Jeep is in drive and you please help me? The Jeep would not start so it got the starter rebuild and it is still not staring nah the computer is not reading the Jeep at all.
I think you did an excellent job on this video. I did have to disconnect / reconnect the battery to reset.MY Transmission is now working without slipping when going from 2 to 3rd. THANK YOU
It's so complicated. I paid a mechanic $822 parts & labour. 3 hours labour. I bought the ECM. I couldn't have diagnoses it. I only found your video. As a DYI'ER I wouldn't even try it.
A very good work, thanks much, I have Nissan note 2008, there's no power supply from the ECM/ECU to coil number 3, and other coils keeps going off, also other ECU can not supply power to on the check engine sign,,
Ground and dc supply etch were thick and good absorb heat.. Therefore you need correct temperature and tip to melt solder lead.. Avoid lifting solder tip once solder lead start to melt . Let the melted solder lead to help spread more heat to surface. This is to avoid cold solder.
the solder is not burned out it is squashed due to the casing screws and is ok,it doesn't need soldering ,if you knew how to do it you would have put flux on the board,all you have done is to show how not to do it
My mechanic just replaced my ECM . I bought it from "Flagstaff"(?) IN New York State $384 programmed and reconditioned. We already tried 2 from local junk yard. I don't know if it was required. I first replaced starter then ignition switch. I wasn't certain, but I'm more doubtful now with your video!
So far, I've spent $230/yr parts and labour over 13 years on my Saturn Ion 2.2 ecotec. I think that's a good deal for a free car with 130k miles on it. My brother told me that is a great deal all things considered to this point, but another BIG job may be a " bridge too far" and that I should consider a used Buick with a 3800 engine,$5000, 2000-2005, nothing fancy. That's the plan.
hi everyone ,if anyone else wants to discover toshiba laptop repair try Saankramer Electronic Magazine System (just google it ) ? Ive heard some great things about it and my m8 got amazing success with it.
I liked your video, but it seems your Weller Soldering Iron has started running cooler than it should be. Taking the tip and the shaft off and cleaning them good at every connection with a fine scrubbing pad are a very light sand paper and cleaning and re-tinning the tip should bring it back like new. I've redone many old irons bringing them back to like new use.
Poor english made this video pure torture to watch. Also show what the ECU is doing before removing it from the car and then show it installed again after the fix. This video is basically a 20 minute video on him soldering some screw holes - who knows or even cares if it actually fixed the issue, right?
I disagree yes I don't have to wear one but the vehicular today are all electronics controlled you just need to drag your feet for like 30 minutes on carpet then touch the micro and that's it hahaha
congratulations on your videos, has taken many doubts. and I have a problem in a 1993 corolla, the electrician moved the air and now the air conditioning key does not activate it and is connected directly by the fan key. and the car goes down slowly because I believe that it is not passing through the central , you can guide me to reverse this. then the slow falls a lot and the car sometimes dies. my name is Wellington I am from Brazil.
PETER FINN, does car PCM modules and ECM modules use CAN buss signals or how do they work? What do you use to test and flash program various ECM and PCM modules?
Hi sir have a nice . My car also same unit of ECU . there's one issue that 4th injector pulse stopped. I checked all cables. All perfectly. Finally I checked ECU in side circuit. There's one. I C ( integrated circuit) damaged. I need cheng that ic . But not available that ic number. Please I beg you ,you can help for me ...?
Can you please help us we have mitsubishi outlander 2016 dosent start after replacing ECU now the IMMO asking for the following keyless operation system service required. So that means we need to program the key to the new ECU and we don't have the original ECU to do so. How can i get back the old data for it? Thanks for your time.
Hi..i had problem with my my car Chevrolet zafira/nabira 2005.. sometimes the aircond cannot running properly.. sometimes its work and sometimes its off automatically..i don't now..maybe it's ECU problem or wiring etc..any suggestions sir..tq..
This is awesome !!! What the hell is this?!?!? lol There are siiks screws on the cirqweet board. 1, zeeeee 2,zeeee 3,4,5,siiks 7... lmao Got to love it. Nice info tho.
Hi Peter, i have an automatic 2001 toyota rav4 vvti 1.8 1zz engine with 125 000 kms and the automatic gearbox does not work in reverse gear, i also see that when changing from low to 2nd and drive that the vehicle seems to slip and jerk. sometimes the check engine light appears but then goes away again. I have heard about it possibly being an ICU problem. could what you done here be the fix to my problem? could this be the problem in my vehicle too?
Nice info, if coil 1 and 4 are working, but 2 and 3 are not working, which components are faulty ? PCB code JG331B09702C1, box = MR44641, Mitsubishi Lancer 2000, I can not see any pulse on my scope from ECU coil 1,4 and 2,3.thanks
Hi sir realy need help trying to replace nissan xtrail 2004 ecu diddnt come with an ecu so i need to match it..Can I use data from other modules like the cluster or somwhere else cos the cluster chip 93c66 and the replacement ecu allso has 93c66
My Lexus IS 250 2009 model, I change the ECU and I program it for 30 minutes then I tried to start it will make a starting sound and trip off, place what do I need to do
I say you should go into learning Industrial Electronics Technology or Electronic/Electrical Engineering Technology at your local community college. Its what I did and I learn a lot about electronics. With that, you'll be able to repair/program car computer boxes.
problem facing in Chevrolet captiva 2007 manual, DTC U0073(Control Module Communication Bus OFF), U0121(ABS MODULE lost communication) and P0500(Vehicle Speed Sensor) ,,,,suddenly instrument cluster stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working, Service Vehicle Soon light & MIL illuminates in cluster. and all happen intermittently and all together but car keep running till next key turn off, however if problem comes in key ignition position then I have to connect-disconnect battery several times then luckily car get started. Can anybody suggest solution?
Can anyone help? I have 4 lights, (ADS, Brake, Traction, and AWD) on my dashboard that won't go off. All but the AWD are working. What could be the problem?
Hay Steve E. I wish I had back the money I've spent at a "proper repair facility". Besides which I had this problem repaired over a year ago at a "proper repair facility". Not the dealer though because actually I am too cheap to allow myself to get ripped off. This is an old post. How did you find it? maybe you should get a life.
I have broblem in my car she was automatic transmission and I change to manual transmission. When I but the manual car computer she won't start. She start only on automatic car computer. Please help me to find the problem
linn it is not for Toyota rav 4 2003 .....I also thought it was for it but I met a man who help me to get my own.........but if you need it you can mail him....bruttobrinex@gmail.com... He will surely help you out in no timr
Hello I'm starting in the area of repairs of automotive electronic plants, in brazil, is there any supplier of electrical circuit boards? Thank you very much for your help
it says on the label 1az fe probably an avensis petrol 2.0 or similar "at" may mean auto? on another note i wouldnt have bothered with the solder but would have sandwiched aluminium washer between the case and the pcb so it would overlap the good groundong points.
Pl share email id so i can send video i have captiva one time overheat car after temprature light blink and car dont turn on also i will try to scan car but car wont communicate scanner with car. Macanic told me may be problem in ecm l
I liked your observation of the board, it’s a very good tip to look at the grounding connections. Your English although not perfect is understandable, and you can get your thoughts across. If I may present a few ideas, try not to use your soldering iron tip on anything else than the solder, circuit board and component leads. It can get contaminated and prematurely worn, plus it can make your job harder. I always test the iron temperature with the solder itself, once it melts you are in the right ball park temperature wise. It should always be able to hold a small solder bead, if it doesn’t either it needs restoration or replacement. Using flux paste massively helps to melt the solder. The quicker it happens the less heat you will transfer to the board and adjacent components that might be heat sensitive. After soldering, a quick wipe with isopropanol will leave a clean and extremely professional look. I hope you take this as a contribution for other viewers that are getting started in electronic repair, aside from this thank you for sharing this video, it’s great to have people who help others improve their knowledge and skill. Most people get scared getting into circuitry as if it’s something massively difficult. As with everything else, there are some general principles to observe, proper techniques and the rest is practice as much as possible. What you did there helps demystify the black box that people see when they look at an ECU and don’t even dare cracking it open. Those usually just get replaced and they are very pricy, while it can just be a cracked joint or loose connection that any beginner can fix with limited knowledge and means. This is a good step forward, seeing how others have done it and following in their footsteps. Overall, you did a good job, I just wish you would have shown if that repair solved the problem. Well done.
Thanks and Good 👍
that is amaziiiiing, thank you thank you
I started watching your videos because your accent helped me to stop stressing out lol
Good and Thank You. :-)
@@PeterFinnTheCarDoctor problem facing in Chevrolet captiva 2007 manual, DTC U0073(Control Module Communication Bus OFF), U0121(ABS MODULE lost communication) and P0500(Vehicle Speed Sensor) ,,,,suddenly instrument cluster stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working, Service Vehicle Soon light & MIL illuminates in cluster. and all happen intermittently and all together but car keep running till next key turn off, however if problem comes in key ignition position then I have to connect-disconnect battery several times then luckily car get started. Can anybody suggest solution?
Peter Finn the Car Doctor hello how are you doing Mr. Peter I have a 2008 Infiniti QX56 Jeep and one day the Jeep started malfunctioning the two side mirrors would open and closed every time the Jeep is started and the reverse cameras would come on when the Jeep is in drive and you please help me? The Jeep would not start so it got the starter rebuild and it is still not staring nah the computer is not reading the Jeep at all.
I think you did an excellent job on this video. I did have to disconnect / reconnect the battery to reset.MY Transmission is now working without slipping when going from 2 to 3rd. THANK YOU
Great info and Thanks ! 👍
Marrie, did you solder the negative contacts too ? And then the car worked fine??
That was professional soldering Peter! Very impressive!
Maybe more soldering in china by manual hands.
that's some advanced sarcasm
It's so complicated. I paid a mechanic $822 parts & labour. 3 hours labour. I bought the ECM. I couldn't have diagnoses it. I only found your video. As a DYI'ER I wouldn't even try it.
Noted
Very nice approach,the earth grounding connections of the pcb to the metal box are making poor contact and thats all is what it faults.
Come on!
There is no “earth” grounding.
There is battery ground.
A very good work, thanks much,
I have Nissan note 2008, there's no power supply from the ECM/ECU to coil number 3, and other coils keeps going off, also other ECU can not supply power to on the check engine sign,,
Thanks for sharing
Ground and dc supply etch were thick and good absorb heat.. Therefore you need correct temperature and tip to melt solder lead.. Avoid lifting solder tip once solder lead start to melt . Let the melted solder lead to help spread more heat to surface. This is to avoid cold solder.
Thank You my Friend. :-)
Thank you from Australia
Thanks for sharing 😀👍
the solder is not burned out it is squashed due to the casing screws and is ok,it doesn't need soldering ,if you knew how to do it you would have put flux on the board,all you have done is to show how not to do it
My mechanic just replaced my ECM . I bought it from "Flagstaff"(?) IN New York State $384 programmed and reconditioned. We already tried 2 from local junk yard. I don't know if it was required. I first replaced starter then ignition switch. I wasn't certain, but I'm more doubtful now with your video!
Noted
So far, I've spent $230/yr parts and labour over 13 years on my Saturn Ion 2.2 ecotec. I think that's a good deal for a free car with 130k miles on it.
My brother told me that is a great deal all things considered to this point, but another BIG job may be a " bridge too far" and that I should consider a used Buick with a 3800 engine,$5000, 2000-2005, nothing fancy.
That's the plan.
Ok.
I love how he counts down the screws he's taking out!
Good 👍😀
You working very good you .it is a lot of pleasure giving you my eyes to see what you doo..keepa upa the vetios I think so..you thank
hi everyone ,if anyone else wants to discover
toshiba laptop repair
try Saankramer Electronic Magazine System (just google it ) ? Ive heard some great things about it and my m8 got amazing success with it.
I liked your video, but it seems your Weller Soldering Iron has started running cooler than it should be. Taking the tip and the shaft off and cleaning them good at every connection with a fine scrubbing pad are a very light sand paper and cleaning and re-tinning the tip should bring it back like new. I've redone many old irons bringing them back to like new use.
Thanks. :-)
HOLY SHIT IT FUCKING WORKED WITH MY TOYOTA RAV4 2002!! THANK YOUUUU
Good comment and Thanks ! 😀👍
What symptoms did you have with your Rav4 2002? I have 2004 Rav4 Automatic and I can't get 4th gear
very informative video, could of got better results using a blow torch
Great suggestion!
I see people trying to tell you how to do what you did but they do not have no video, they watching you, bunch of bums
It's very cool. if this video is watched by someone who does not have 220 volts grounded, then you attach 110 volts to your hand.😀😀😀
Good comment 👍
Thank you for your effort 👍😎
Poor english made this video pure torture to watch. Also show what the ECU is doing before removing it from the car and then show it installed again after the fix. This video is basically a 20 minute video on him soldering some screw holes - who knows or even cares if it actually fixed the issue, right?
Ok
@@PeterFinnTheCarDoctor where are tellfone for
Thanks for the video
Our pleasure!
Do you get zinc solder hairs on these? or do they use lead solder making them
Please remove the grounding cable all the best engineers know its complete baloney to wear one... You won't damage anything...
I disagree yes I don't have to wear one but the vehicular today are all electronics controlled you just need to drag your feet for like 30 minutes on carpet then touch the micro and that's it hahaha
Better safe than sorry...
congratulations on your videos, has taken many doubts. and I have a problem in a 1993 corolla, the electrician moved the air and now the air conditioning key does not activate it and is connected directly by the fan key. and the car goes down slowly because I believe that it is not passing through the central , you can guide me to reverse this. then the slow falls a lot and the car sometimes dies. my name is Wellington I am from Brazil.
PETER FINN, does car PCM modules and ECM modules use CAN buss signals or how do they work? What do you use to test and flash program various ECM and PCM modules?
Tel 4ne bomber
Peter
Your lucky, most of the ones I have opened are coated with a rubber like substance so you CAN'T service them!
Hi, and Thanks for comment. 👍😀
True
Did it work after soldering the negative contacts?? Please let us know.
Hi, it needs also more soldering, but now it is Ok !
@@PeterFinnTheCarDoctor more soldering at the same spots? or is there any other spot?
Very good master
Many many thanks 👍
Hi sir have a nice . My car also same unit of ECU . there's one issue that 4th injector pulse stopped. I checked all cables. All perfectly. Finally I checked ECU in side circuit. There's one. I C ( integrated circuit) damaged. I need cheng that ic . But not available that ic number. Please I beg you ,you can help for me ...?
Noted
Very good fascinating video you make totally ;)
Thank you very much!
Looks like an excess torque assembly issue. Nothing major, but most manufacturers are revamping their manufacturing process this decade anyways
Thanks Sir. :-)
Did it fix the problem?
thank you bai ,,,please healp me
OK.
Mr peter can every board separate like this coz mine is not .the other end of the metal casin is not
Thanks fo rcomment 👍😀
Yes I like your job but you don't work on short circuit on board how fund a short circuit training
Can you please help us we have mitsubishi outlander 2016 dosent start after replacing ECU now the IMMO asking for the following keyless operation system service required.
So that means we need to program the key to the new ECU and we don't have the original ECU to do so.
How can i get back the old data for it?
Thanks for your time.
Very good
Thanks
If I need to replace it. And my car is VW Golf 5, 2.0 diesel. 2005 I have to find ECU only from specific cars like that?
Thanks for info 👍😀
Do you remember what code number you got in your car made you fix the computer
Very nice video.
Thank You. :-)
Very good video
Thank You Sir for feedback. :-)
Hi..i had problem with my my car Chevrolet zafira/nabira 2005.. sometimes the aircond cannot running properly.. sometimes its work and sometimes its off automatically..i don't now..maybe it's ECU problem or wiring etc..any suggestions sir..tq..
Thanks for sharing
how can that material on the soldered part damaged? is it because of heat? if yes, then i should be very careful with my engine cooling system
Noted 👍
GREAT SIR, HOW WE CAN FIND OUT THAT THE PCM HAS SOFTWARE PROBLEM OR HARDWARE.
Thanks 😀👍
This is awesome !!! What the hell is this?!?!? lol There are siiks screws on the cirqweet board. 1, zeeeee 2,zeeee 3,4,5,siiks 7... lmao Got to love it. Nice info tho.
Hi, this is actually Brain test my friend ! :-)
Hi Peter, i have an automatic 2001 toyota rav4 vvti 1.8 1zz engine with 125 000 kms and the automatic gearbox does not work in reverse gear, i also see that when changing from low to 2nd and drive that the vehicle seems to slip and jerk. sometimes the check engine light appears but then goes away again. I have heard about it possibly being an ICU problem. could what you done here be the fix to my problem? could this be the problem in my vehicle too?
Yes, you might have this issue, If engine failure light is ON
Nice info, if coil 1 and 4 are working, but 2 and 3 are not working, which components are faulty ? PCB code JG331B09702C1, box = MR44641, Mitsubishi Lancer 2000, I can not see any pulse on my scope from ECU coil 1,4 and 2,3.thanks
Try again
Hi mate! I change the ecu kit to my astra h 1.6 easytronic gearbox but still doesnt start. I have the imobilliser lightbon dash. What should i do?
Ride a horse.
Thanks for Your info 👍😀
Good job but have you seen any components die from static discharge ?I always ground
myself with my radiator :))...
Good and Thanks Sir. :-)
Hi sir realy need help trying to replace nissan xtrail 2004 ecu diddnt come with an ecu so i need to match it..Can I use data from other modules like the cluster or somwhere else cos the cluster chip 93c66 and the replacement ecu allso has 93c66
Very bad vedio he also don't know about the ecu reparing
Very bad vedio he also don't know about the ecu reparing
Very bad vedio he also don't know about the ecu reparing
00971529824841
Hello Sir i need
f6a t/c 2wd 4at
33920-74G8 1 wiring diagram plz
E=mc2 👍
Hi Peter finn, how do I find a pin code for Bosch ECU for MAN f2000 truck the pin code. Thanks
Ok and Well.
What does ok and well mean?
Try Wurths's Soldering wire.
Thanks for comment. 👍😀
with a better soldering iron and thinner tin and using flux the solder would remain at 100
Thank You Sir. 😀👍
My Lexus IS 250 2009 model, I change the ECU and I program it for 30 minutes then I tried to start
it will make a starting sound and trip off, place what do I need to do
Visit the Dealer
Yes
what do i need to study to repair/program car computer box? i saw someone repair it from a laptop
I say you should go into learning Industrial Electronics Technology or Electronic/Electrical Engineering Technology at your local community college. Its what I did and I learn a lot about electronics. With that, you'll be able to repair/program car computer boxes.
EEPROM'S , MOSFET, BINARY CODING AND GET A PROGRAMMER .. THE TL866 PLUS 2 MINIPRO IS CHEAP AND GETS THE JOB DONE ......
Hello I'm George from Kenya a mechanic and I'm interested to learn how to repair car ECU
👍
Why this has been happened
Sir,
when we replace the car cpu unit want to be change the key set also ; that's why? ?
Yes, key and cpu
problem facing in Chevrolet captiva 2007 manual, DTC U0073(Control Module Communication Bus OFF), U0121(ABS MODULE lost communication) and P0500(Vehicle Speed Sensor) ,,,,suddenly instrument cluster stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working, Service Vehicle Soon light & MIL illuminates in cluster. and all happen intermittently and all together but car keep running till next key turn off, however if problem comes in key ignition position then I have to connect-disconnect battery several times then luckily car get started. Can anybody suggest solution?
Can anyone help? I have 4 lights, (ADS, Brake, Traction, and AWD) on my dashboard that won't go off. All but the AWD are working. What could be the problem?
If you have an ABS module that is not Working, it can cause these symptoms.
The problem is you are too cheap to take it to a proper repair facility for diagnosis and repair.
Hay Steve E. I wish I had back the money I've spent at a "proper repair facility". Besides which I had this problem repaired over a year ago at a "proper repair facility".
Not the dealer though because actually I am too cheap to allow myself to get ripped off. This is an old post. How did you find it? maybe you should get a life.
@@jinxfarque - 👈 triggered
Noted 👍
ASMR.
Did it worked?
Sometimes. There are also specific electric shops in UK, what repairs these.
@@PeterFinnTheCarDoctor your english poor n didn't understand your job
Is there business opportunity for ecu repair
Yes 👍😃
I have broblem in my car she was automatic transmission and I change to manual transmission. When I but the manual car computer she won't start. She start only on automatic car computer. Please help me to find the problem
My model car 1996 toyota corolla I do swap manual gearbox but I don't swap the engine computer. My main problem is the car can't go up 190 km
Ok, you must replace all cables and sensors and ecu.
did that fix the problem with the transmission?
Yes. :-)
@@PeterFinnTheCarDoctor what kind of transmission problem it was?
Sir aap kha se ho
I just wonder if you can reflow ECU circuit in oven? I did many of my Dell computers in the past
Yeah
Toss it in with your Thanksgiving Turkey 🦃.
Just kidding video!
I get all the work in this ECM Ecu
Thanks for comment. 👍😀
Buenas tardes, estoy buscando el diagrama de la ecu del toyota vitz rs, tendras algun dato que me ayude?
Puedes meter te en Google del telefono o en la computadora tambien. Alli puedes en contrar lo q usted quiera. Aver si lo encuentras.
is this for the toyota rav4 2003 modell?
linn it is not for Toyota rav 4 2003 .....I also thought it was for it but I met a man who help me to get my own.........but if you need it you can mail him....bruttobrinex@gmail.com... He will surely help you out in no timr
Yes. Same ECU
My ecu not working on car and how much it costs to fix nissan edu?
About 2000 USD
Can a cars cpu be repaired?
Wished I could understand half his words.
Hi and Thanks for comment. :-)
how to colour wiring ground ecu toyota innova? thanks
I have my car no connection white obd and no lights in gearbox dashboard and not working
Ok, thanks for info. 👍
thanks
Thank You. :-)
Hello I'm starting in the area of repairs of automotive electronic plants, in brazil, is there any supplier of electrical circuit boards?
Thank you very much for your help
Ok
Maravilha...so faltou os resistores.....
is this ecu for toyota Hiace diesel ?
No
it says on the label 1az fe probably an avensis petrol 2.0 or similar "at" may mean auto?
on another note i wouldnt have bothered with the solder but would have sandwiched aluminium washer between the case and the pcb so it would overlap the good groundong points.
Hello can you repair continental getrag dc4 tcm
Maybe
Turn the auto-captions on please. Thanks
Good comment and Let's All folk discuss more 👍😀
Peter Finn the Car Doctor Turn the Subtitles/Captions on please.
Mercy
Thanks for comment 👍
My Toyota starts and runs as long but when stop and switch off swing and no start every time
HI, please do new video to me ?
Pl share email id so i can send video i have captiva one time overheat car after temprature light blink and car dont turn on also i will try to scan car but car wont communicate scanner with car. Macanic told me may be problem in ecm l
Sir result lodgy ka ecm repier karna ha sir
I'm looking for ECU for Toyota Hilux diessel 2kd 96
👍😃
Is the arm earth clamp really needed?
Yes
Starter motor restoration démarreur now canam 800
What was fault code?
Thanks 👍
I'm looking for the ecu for Maruti omni cargo van
@@Kawy_Mwiti suzuki ertiga 2015 ?
Sounds like Stephen hawking
Yes Yes. Stephen was my Hero too.
ralli englanti :D
👍😃
Geeze that was painful to watch...
21 mins just to say check the grounding tabs... 🙄
Noted 👍
Can i ask you?
👍
rubber gloves with earth strap????..........ok
Thank You Sir 👍😀
I can not see that small spot .
Noted 👍
Who repairs ECU 2007 Cadillac CTS
Noted 👍
I have any one ecu have who he is want to contact with me
ECU CHAHIYE Chevrolet captiva 2007 2.0LT Model 150BHP 110KW
@@harshkhy
Sir you send me your ecu part number
@@zahirshah3308 96892367
@@zahirshah3308 EDC16C39 BOSCH