Use some dielectric grease on those connections, fill the connector up with it If you want. Also see if the connector terminals haven’t expanded or stretched a bit, they can be tightened up by just lightly squeezing with pliers.
Hmm ok I was thinking it takes more power to make them brighter and see some of the bikes struggling with charging power after installing xnons battery get drained like 5 times faster but if you say
I'm an electrician and everyone thinks this way. Mainly because of flashy advertising such as "12,000K SUPER BRIGHT LED". K = Color of actual light emitted, lumens = Brightness
Hi, my battery just died not long ago from leaving the key on and since then it lasted 4 months just fine til recently it died, wouldn't start. Now that I bought a new battery I just installed it, turned it on and idle and gave it some revs and stuff but I didn't go for a ride, let it sit there for 2 days and now I went for a ride the 4rd start up (rode stop rode stop etc) and now its acting up, once I turn it on and crank it the cluster goes blank for a second. I think its because when I installed it on I didn't take it for a ride to let it charge the battery properly. Could that be the problem? It's a agm battery 190cca 8.6ah mottobatt mbtz10s. Same battery as when I bought the bike. Thanks for the video guide!
Just make sure there is good connection to the battery positive and negative! Also test have many volts battery shown when bike is not running Should be 12 to 12.8 volts for new battery end then start bike and check again should be minimum 13,5 v if not your rectifier is playing up! If all measurements are good then something else is draining your battery like alarm or stator is on fault but unlikely check the first steps and you will know strait away
@@r91motorswelcome79 @Mike T thanks I figured it's cos I didn't take it for a ride/rip straight away after putting it on. I started it again today after 2 days and it fired straight up very quickly though so there's that and I kept it revs above 5k rpm and kept reving it for 2 minutes, hopefully thatll put some juice into it. I think (cross fingers not) that my rectifier or stator is playing up, or could be starter relay solenoid as I remember for a week when I turn the ign.on I would here a clicking sound so there's that.. Or I might be mistaken that our bikes don't charge the battery once you start it it runs off the electrical system - the bike on its own basically.. 🤷♂️ I'm not too mechanically inclined but do have basic knowledge..
@@r91motorswelcome79 It was definitely the stator. The bolt heads in the stator had somehow come a bit loose and the heads were smoothed out to where I couldn't even see the grooves on the head. I knew I heard a bit of grinding. Oh well.
I went And search the paint code for the 2010-2015 corvettes Since their yellows are a beautiful color, I would just use that if you had wanted to paint the fairings👍🏼
Hi thanks for the video. I've got the same bike as you. Please tell me because my charging voltage is about 13.78 max. Stator is OK. Rectifier I will check once again but I think Ok. Battery is fully charged. Spec. Says it should be above 14 v 14 -14.5v. Any idea why I have max 13.78? Cheers
@@r91motorswelcome79 My girls R6 had corrosion on her rectifier, we cleaned it, and it got better, but it still wasnt charging, so we ended up getting a new OEM rectifier and shes riding again. Cheers for the good informative video! Your bike is sick too, the fluorescent yellow is dope
You can buy a kit that replaces the clip. It’s like 10-15 USD, and it’s worth it. Try eBay or Amazon. I replaced mine a few years ago and it’s an easy fix
There is a burn in negative in the socket going to rectifier is there any effect on causing error and battery not charging? My stator is good i checked it already and my rectifier.thank you for your answer sir..
@@Ryan_1997 Hi, my battery just died not long ago from leaving the key on and since then it lasted 4 months just fine til recently it died, wouldn't start. Now that I bought a new battery I just installed it, turned it on and idle and gave it some revs and stuff but I didn't go for a ride, let it sit there for 2 days and now I went for a ride the 4rd start up (rode stop rode stop etc) and now its acting up, once I turn it on and crank it the cluster goes blank for a second. I think its because when I installed it on I didn't take it for a ride to let it charge the battery properly. Could that be the problem? It's a agm battery 190cca 8.6ah mottobatt mbtz10s. Same battery as when I bought the bike. Thanks for the video guide!
My 06 R1 won’t start but click on the relay solenoid. New stator with flywheel and gasket, new battery , new relay solenoid , new rectifier. I’m out of ideas this is frustrating
@@r91motorswelcome79 I don’t believe so it just turns on then relay clicks and dashboard rests like I turned off my ignition and turned it back on. Very frustrating
@@almightytwisted935 don’t think there is something massively wrong did bike was starting before and when did this problem start needs to understand what’s happened
It’s just a little pin to press and shoul come of but in your case could be a problem with wiring maybe corrosion or or something to do with wiring burn and like welded together needs to get of some have maybe worm up with something or try w40
amazing have the same problem now i know what to look for thank you very much for this video
Use some dielectric grease on those connections, fill the connector up with it If you want. Also see if the connector terminals haven’t expanded or stretched a bit, they can be tightened up by just lightly squeezing with pliers.
Saved me I couldn’t find anything on this
8000 K means just colour. It is more blue. If you had 3000 K it would look yellow. It doesn't mean power, brightness or quantity of electricity use :)
Hmm ok I was thinking it takes more power to make them brighter and see some of the bikes struggling with charging power after installing xnons battery get drained like 5 times faster but if you say
I'm an electrician and everyone thinks this way. Mainly because of flashy advertising such as "12,000K SUPER BRIGHT LED". K = Color of actual light emitted, lumens = Brightness
How long did this fix last. Did the negative get burnt again or what?
Hi well it still runs even now !!
Hi, my battery just died not long ago from leaving the key on and since then it lasted 4 months just fine til recently it died, wouldn't start.
Now that I bought a new battery I just installed it, turned it on and idle and gave it some revs and stuff but I didn't go for a ride, let it sit there for 2 days and now I went for a ride the 4rd start up (rode stop rode stop etc) and now its acting up, once I turn it on and crank it the cluster goes blank for a second. I think its because when I installed it on I didn't take it for a ride to let it charge the battery properly. Could that be the problem? It's a agm battery 190cca 8.6ah mottobatt mbtz10s. Same battery as when I bought the bike.
Thanks for the video guide!
Just make sure there is good connection to the battery positive and negative! Also test have many volts battery shown when bike is not running Should be 12 to 12.8 volts for new battery end then start bike and check again should be minimum 13,5 v if not your rectifier is playing up! If all measurements are good then something else is draining your battery like alarm or stator is on fault but unlikely check the first steps and you will know strait away
@@r91motorswelcome79 @Mike T thanks I figured it's cos I didn't take it for a ride/rip straight away after putting it on. I started it again today after 2 days and it fired straight up very quickly though so there's that and I kept it revs above 5k rpm and kept reving it for 2 minutes, hopefully thatll put some juice into it. I think (cross fingers not) that my rectifier or stator is playing up, or could be starter relay solenoid as I remember for a week when I turn the ign.on I would here a clicking sound so there's that..
Or I might be mistaken that our bikes don't charge the battery once you start it it runs off the electrical system - the bike on its own basically.. 🤷♂️ I'm not too mechanically inclined but do have basic knowledge..
I'm having the same issue and I did all these checks and it didnt help. Is my next step checking the stator? Great vid and walkthrough!
Yeah try that but double check rectifier most of the cases is rectifier
@@r91motorswelcome79 It was definitely the stator. The bolt heads in the stator had somehow come a bit loose and the heads were smoothed out to where I couldn't even see the grooves on the head. I knew I heard a bit of grinding. Oh well.
Pleaseeeeeeeeee can you tell me what kind of yellow that bike is and where I can get some?!?! Love the video ☺️ thanksss
I went And search the paint code for the 2010-2015 corvettes
Since their yellows are a beautiful color, I would just use that if you had wanted to paint the fairings👍🏼
I would call that a generic highlighter yellow or high vis green/yellow, hopefully that can help start your search
Hi thanks for the video. I've got the same bike as you. Please tell me because my charging voltage is about 13.78 max. Stator is OK. Rectifier I will check once again but I think Ok. Battery is fully charged. Spec. Says it should be above 14 v 14 -14.5v. Any idea why I have max 13.78? Cheers
This is a great video
Thank you!! Hopefully it will. Help some have
@@r91motorswelcome79 My girls R6 had corrosion on her rectifier, we cleaned it, and it got better, but it still wasnt charging, so we ended up getting a new OEM rectifier and shes riding again. Cheers for the good informative video! Your bike is sick too, the fluorescent yellow is dope
@@RideFastDontDie thanks man hope get some tip from this vid and all will be good with bike
Thanks having the same problem
hi m8, does the procedure for testing the rectifier also work for a 2014 model?
I think yes only pin order maybe different but Should work
Beautiful bike bro
Thanks
Great video man im having the same problem , what did you use to clean the connector??
I did use sandpaper and little screwdriver also can use some spray like carb cleaner or w40 something what take that stuff off
You can buy a kit that replaces the clip. It’s like 10-15 USD, and it’s worth it.
Try eBay or Amazon. I replaced mine a few years ago and it’s an easy fix
@@mikoeeebs what's the kit called
@@mikoeeebs what is the kit called pops
There is a burn in negative in the socket going to rectifier is there any effect on causing error and battery not charging? My stator is good i checked it already and my rectifier.thank you for your answer sir..
You ever fix this or get a answer ??I got the same problem
Beautiful bike
🙏 thanks
Great help
How did u clean the ground wire??
Just used knife sandpaper also some sprays basically anything what can get rid off that all that bad stuff
I’d like a video on that..😂 sounds easy till u see how small the space is..
Thanks
I have a 2007 Yamaha R6 and when I turn the throttle, the voltage starts to drop to 5-6-7. What's the problem?
Test the stator and rectifier.
Usually it’s the rectifier. Mines blown out and drops the voltage
@@Ryan_1997 Hi, my battery just died not long ago from leaving the key on and since then it lasted 4 months just fine til recently it died, wouldn't start.
Now that I bought a new battery I just installed it, turned it on and idle and gave it some revs and stuff but I didn't go for a ride, let it sit there for 2 days and now I went for a ride the 4rd start up (rode stop rode stop etc) and now its acting up, once I turn it on and crank it the cluster goes blank for a second. I think its because when I installed it on I didn't take it for a ride to let it charge the battery properly. Could that be the problem? It's a agm battery 190cca 8.6ah mottobatt mbtz10s. Same battery as when I bought the bike.
Thanks for the video guide!
same prob with connector rusted / burnt
My 06 R1 won’t start but click on the relay solenoid. New stator with flywheel and gasket, new battery , new relay solenoid , new rectifier. I’m out of ideas this is frustrating
Did your fuel pump come up when ignition is on?? Did you check tilt sensor maybe that one playing about
Also maybe be you got some alarm fitted
@@r91motorswelcome79 I don’t believe so it just turns on then relay clicks and dashboard rests like I turned off my ignition and turned it back on. Very frustrating
@@almightytwisted935 so there is no alarm ?
@@almightytwisted935 don’t think there is something massively wrong did bike was starting before and when did this problem start needs to understand what’s happened
How did you get the rectifier connection off? I for the life of me cannot remove the connector
It’s just a little pin to press and shoul come of but in your case could be a problem with wiring maybe corrosion or or something to do with wiring burn and like welded together needs to get of some have maybe worm up with something or try w40
For anyone moving around the brake reservoir, dont shift around the fluid too much if air gets in that brake line you'll have to bleed the rear brake
😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂 so riding over bumps gets air in???
4th hi hi
Does someone actually employ you