DIY 0-29V 5A Bench Power Supply (XL4015 5A Step Down Module)
ฝัง
- เผยแพร่เมื่อ 15 ก.ย. 2024
- 0-29V 5A Bench Power Supply make using XL4015 5A Step Down Module
Materials Required:
1. Potentiometer Knobs x2 - bit.ly/31IQDML
2. Power Connector socket Male 12V - bit.ly/3gwVx3H
3. 24V Switch On/OFF - bit.ly/2YWEdik
4. WXD3-13-2W 10K Wirewound Potentiometer x2 - bit.ly/2VP11Pk
5. Banana Socket Jack Red & Black - bit.ly/2NXszNU
6. 3mm LED Blue & Red - bit.ly/3gqrjPx
7. 3mm LED Holder x2 - bit.ly/3itkNcI
8. XL4015 5A Step Down Module - ebay.to/2BvZoPE
9. Wires
10. Wood Panels
DIY Tools Used:
DIY Table Saw - • DIY Table Saw (How to ...
DIY Clamp/ Vice - • Make A Drill Press Vis...
Mini Belt Sander (895 Motor) - • Electric Adjustable Sp...
Minleaf 96W 12V-24V Power Supply Adapter- • Minleaf 96W 12V-24V Po...
Subscribe LahisTech: bit.ly/2JHtlyc
Subscribe for more future creative project videos.
Thank you.
Sir apaka kaam bohot accha hai .......... Love ur videos😀
it is a very clever way to usage of the module.
Good work sir... Please, I want to know the voltage of the LEDs used outside the board, as you did?
Good job with all the best information and knowledge
nice work! :D
little advice: take a bit of masking tape and glue it over the LED meters.
it will make them more readable, because they are way too bright! :D
К=анр111¹111111
*Moin, ich frage mich, was diese 'Netzteile' für einen Sinn haben!?* Käse!
Kann denn niemand heutzutage mehr ein anständiges solides Trafo-Netzteil mit Gleichrichter, LM723 und einer Transistorendstufe mit 2N3055 aufbauen??
genau!
simply said, those "old school trafos" are very hard to find, and the newer ones are very expensive!
but these modules are cheap, and a "laptop brick" is cheap and easy to find, too.
and anyway, linear power supplies are nicer hot at high amps, and these switched modules, at 4-5 amps (it depend of their ratings) are really cold... anyway, room temperature, maximum. :)
So super nice work
Nice job there! They are good modules too.
Sir ur too good 👍
I used transformer 9 0 9 5408 diode in my xl4015 module. Now it shows 23 volts but after loading it becomes 9 volts, why is this happening? And what to do.
Can I solder a normal 100 kOhm resistor to a 100 kOhm multiturn potentiometer in order to get to 200 kOhm? Can't find a 200 kOhm multiturn potentiometer! My step up booster uses the 204w trimmpot
I want to know wich is the minim current (mA) that this board meassure, the sensibility
Can adjust the current?
Yes, this module is a buck-boost with CC/CV. You just short out the positive and negative outputs at a LOW voltage (4-7v) and then adjust the current limit with the potentiometers. Then it wont go above that limit.
I actually just read up on their instructions and they recommend using a multimeter amperage circuit to set these, so just use that by shorting it out in the same way.
Can I use 19.5v 4.7a adapter for this xl4015 step down module?plz reply.....🙏
Yes
What about the heat
Can use as phone charge
great DIY work, congratulations. I have 2 questions.
1. There is no cable between the 7-segment layer and the sub-layer but how does the screen work?
2. What was the 3-pin and 2-pin on the top layer for you removed from?
1. It has terminal hole there and a brass connector act as wire.
2. He removed potentiometers (Trimpots) that control voltage and current.
Can use like as charger?
Blue led What work
Muito bom eu gostaria de comprar uma de o a 3o voltes
Bel proggetto!
Mantap sir....
wires de caunto calibre es
Wow
Sir aapka product kharidna chahe to kaha se kharide
Am I the only one here who doesn't like the idea to put bench PSU into the box made of flammable materials?
youtube is drunk again 5 likes 1 view
Total kitna rupe ka khrcha hai ese banene main
hi
Tell me
you eBay page Error
Which one?
Please sent your whatsapp No
I want to buy this product from you
Current pot not working 😂😂😂
first