How to Replace Starter 1994-2002 Dodge Ram 2500

Buy Now!
New Starter from 1AAuto.com trq.video/ia-1...
This video shows you how to install a new starter on your 1994-2002 Dodge Ram 2500. The starter is a powerful electric motor that gets your engine to turn over when you turn the key in the ignition switch. If a motor has worn out or become damaged, your vehicle won’t start.
This repair was done on a 2002 Dodge Ram 2500 Base 5.9L Extended Cab Pickup 4-Door 4WD Automatic and the process should be similar on the following vehicles:
1994 Dodge Ram 2500
1995 Dodge Ram 2500
1996 Dodge Ram 2500
1997 Dodge Ram 2500
1998 Dodge Ram 2500
1999 Dodge Ram 2500
2000 Dodge Ram 2500
2001 Dodge Ram 2500
2002 Dodge Ram 2500
Tools you will need:
• Flat Blade Screwdriver trq.video/obni...
• 11mm Socket trq.video/obyK...
• 13mm Socket trq.video/obyK...
• 16mm Socket trq.video/obyK...
• Ratchet trq.video/obEc...
• Gloves trq.video/oadt...
• Sandpaper
• Floor Jack trq.video/o7U-...
• Jack Stands trq.video/oVz-...
• Wheel Chocks
• Wire Brush trq.video/otw-...
Subscribe: / @trq
Check out our playlist:
Dodge Ram 2500 1st Generation 1994-2002: • Dodge Ram 2500 1st Gen...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@RonnieWVideos]

May want to specify what Dodge 2500. Great video but it doesn’t apply to my Dodge 2500 that is a diesel. 3 bolts that require a 10 mm e-torque socket. Also instead of a clip, it’s a 1/4 or 5/16 nut that comes off for the ground screw. 16mm is correct for the hot wire. Battery on my 2500 diesel is 12mm not 11 mm. Not bashing your video, just needs more specific title. Great video for a gas burner.

[@erikwright197]

I just saved myself a hundred and fifty bawks

[@tomburns890]

Our Gen 2 Cummins just clicks when trying to start and when trying again, it will start or click a few more times then start. Do u think it’s the solenoid or starter? Thanks

[@user-et3sv7gn8f]

Great video I have a 2001 Dodge Dakota SLT 3.9 tried to put new starter in and for the life of me I cannot get the signal wire plugged in on the starter it does not push in all the way are literally tried this for an hour and then gave up

[@benitogonzalez9281]

my question is why don't u guys show the full video you guys make it look easy

[@gregm3771]

Didn't show removing the top bolt

[@kimtack7543]

What to do if starter won't come out after bolts are removed

[@AtwoodBoxing]

This video is a lie!. I have the 2001 5.9 cummins my power wire was a 24mm