Thank you so much for this! We just moved in a 75 year old house which had old carpeting over hardwood floors. We have used a drum sander and edger and we're ready to refinish. This is the most helpful video I have watched at youtube! Blessings to you!
@ceetheninja1 I agree. I've looked a so many but this video really showed the steps in between. I would like to know drying tines in between sending tho
Realmente se puede limpiar con trapo húmedo si voy a aplicar un poliuretano en base de aceite. I can wipe with water if I’m going to use polyurethane oil base .
@@briceschwartz407 I think he used this one: www.homedepot.com/p/Linzer-10-in-Lambskin-Pad-with-Block-10-in-Lambskin-Floor-Applicator-Refill-Pad-w-4-ft-Wood-Ext-Pole-with-Metal-Tip-HD11001-HD11002-RP548HM4800/315857773
This video is good! I wish I had seen it just a few hours earlier. I just finished my first coat of poly and came up to watch TH-cam to unwind, and the explanation in this video about not being afraid to press hard on the applicator would have helped me. It _will_ help me with my second coat.
Thanks for this video I believe it will help me more than any other tutorial I have seen and I have watch hours. No one showed how much material was used and no one said to use heavy pressure on the applicator. Thanks again.
Thank you for sharing all the excellent tips especially clean lambswool with tape a couple Fuzzy's in your polyurethane can really mess up your day you can tell you take a lot of pride in your work with the results you get have a great day
I use tack clothes to clean the hardwood floor before doing any polyurethane and mineral spirits after that on the hardwood and let dry. . Everything else I do the same as you, but I also clean the ceiling, above doors, windows, window aprons, anywhere there may be dirt or dust. Cleanliness. I also use a paint tray. and set my gallon of poly on plastic or a cardboard for dripping or spillage as it can occur.
Great video did something similar but a slight variation your shoes Sal Flores for hardwood floors great idea I’m gonna do that from now on when I do hardwood floor’s again thanks for the idea😄 Wow your hands hand with a pole that’s a lot of work Sal.
Good video for applying finish. The amount of water you used to clean the bare wood floor was bound to raise the grain. Even a damp rag will raise grain on bare wood.
I just used this same poly then read the can to see how long until it dried and it said not recommended for floors and to use the floor finish of that brand found this cause I was wondering how bad of a mistake I made assuming it doesn't matter
Says right on that can, not recommended for floors. Varathane Ultimate poly is not for floors. They have different mixture for floors. I made the same mistake had to re-sand the floors
Hi Sal! You gave me the confidence to use a belt sander! Excellent sanding instruction in video 1. I watched the finishing video.... so I understand don’t go thick and use pressure on the applicator to push it in. Light sanding between coats vacuum and tack or damp wipe. After second coat you closed by saying sand with 150 grit? So should I add a 3rd coat, if not why the sanding after second coat? Thanks again!!!
I've seen this question on here a few times. Since he used an oil-based stain, it calls for two coats, but it is OK to apply three. If you apply three coats, most polyurethanes do not require sanding between each coat, but it is good to sand before the last coat with sandpaper between 150- to 220-grit.
He was just repeating himself, he did NOT mean that you have to sand the 2nd coat. If you did sand the 2nd coat, you should apply polyurethane same way he did the 1st and the 2nd.
To all those that are getting ready for doing a second coat… BE CAREFUL SANDING!!! I had to remove the first coat after over sanding, as it would show scratches through. Super pain in my ass. 220 grit is recommended, and go very lightly.
Interesting. I was told to Not apply pressure during application, as it will force air bubbles into the poly. Is it the mineral spirits that prevent this?
When I do this, I wipe the bare wood with mineral spirits. Bare wood and water is not a good idea. I like how they prep the pad with tape to pull up loose fuzz, I’ll do that next time
Exactly… If you are using an oil based polyurethane you never want to use water and always mineral spirits. The biggest issue is that the water will raise the grain.
@@Reefdevil on a floor I can see how it might be a pain, but water will pre-raise the grain so you can lightly sand it off before finishing. Of course make sure it dries completely and then come back with mineral spirits.
Is it ok to use wood glue as sealant before applying water-based glossy varnish (maybe polyurethane) on wood floor? Or you can apply the varnish directly and then sand the floor with #1000 grit or higher for a smooth finish?
I pay someone and they did a horrible job theres a few bubble 1 size looks like it have to much polyurethane looks thick and the other side dont look as shinning how can I fix ? Can I sand it without damaging paint on wood?
Nice job, Sal! I just found your video, and it is very helpful. One question though. It seems that you used the Varathane "interior finish" ultimate polyurethane on your floor. The label on the can recommends that the "interior finish" should be used on furniture, time, etc inside a house, but not for the hardwood floor. I know a lot of people did use the "interior finish" on the hardwood floor anyway. Just curious how durable the finish on your hardwood floor is after two years. Thanks.
Just going to tell you right now for everyone watching this video if you use the exact same can of polyurethane that he is using on hardwood floors... read the whole back of the can first because it says to use a specific kind of poly made by the same brand that is for wood floors, that is not for wood floors. Read the damn can. This is a general poly, not made for wood floors. Sure it can be used, but Varathane makes their own specialty polyurethane for WOOD floors.
Hey Sal how much do you charge per sq ft? And great job by the way. The only thing I didn’t see which I come across when I’m sanding floors is that there are some corners that that small sander can’t hit in Closets etc. This is what I use a hand sander whether it be a square one or a belt sander to reach in areas that those big machines plus the small rolling sander can’t hit.
I polyurethaned some faux beams I made from drywall that I painted with latex and then gel stained...when I purchased the polyurethane I chose satin...in order to give added protection I applied it very heavily...it came out extremely high gloss, the shiniest gloss I’ve ever seen....unfortunately I wanted satin, or a flat finish...I tried hitting it with steel wool, and even comet to reduce the glossy sheen...but that doesn’t work ,because of how rough I made the beams...is there any product you know of that I can go over the glossy urethane with in order to make it duller looking or flat looking?
Based on how he is applying the polyurethane, it may cause bubbles. It is best to drag the polyurethane; pour a line and drag it, and then pour another line on the wet edge and repeat. He is doing more of a mopping motion. I also recommend not wiping the floors down with water, rather mineral spirits. Water, denatured alcohol, or a 50/50 mix of each is best for stain, specifically dark stains. Application of mineral spirits is best used as a pre-application before polyurethane. The use of mineral spirits is also very beneficial when applying water-based polyurethane over an oil-based stain, after it is dry. The use of mineral spirits better ensures that white patches do not form after application of water-based polyurethane over oil-based stain.
I read from supposedly hardwood floor expert. And that is to never use lambs wool brush applicator. So definitely I am confused. Just looking for best way to avoid bubbles. Thanks
@@cjones22p Yes. I do not agree with his technique, as well. He is going over it too much. He has to pull the polyurethane, add another line and pull, etc. But, if his way worked, then who I am to tell him different....
Just found your videos!!! I want to sand down my paint- stained hardwood floors that were never varnished...just raw hardwood planks and has many gaps between planks...any advise on how to approach this? Any advise is welcomed
Hello Sal and everyone reading this comment. I need help with a problem I have after applying the same Finish Coating, when it dries the resul is not smooth in same areas, it is rough and looks like cracking. I don't know what is causing this problem. Can any one help. ??? Cheers!!
I have same problem - I put it on too thick. It's been two days and those areas are still soft. I may end up scraping it off and sanding then re-applying.
So as a floor professional don’t use water or mineral spirits to wash the floor it’s completely unnecessary and if you miss a spot you will see it. I also wash my lambs wool in the washer and then dry it to remove any fuzz, it works a lot better. Also avoid products at big box hardware stores buy a decent quality floor finish.
Nope. You're doing this wrong if you apply water to bare wood. Water make the wood pore open up and end up needing to be sanded again befor the poly aplication. Vaccum and tack cloth the area and use mineral spirits to dampen a rag if you must.pleas folks do your self a favor dont use water on bare wood.
The sanding he does between coats accomplishes a similar goal. I'm guessing since this is a diy tutorial for people to do at home he's not going to use a buffing machine since most don't have access to one.
As someone who does this for a living I admire anyone who attempts this without the proper tools. Do me a favor buy a respirator with charcol filters next time you do a coat of poly. Wearing a Covid mask will not protect you
Thank you so much for this! We just moved in a 75 year old house which had old carpeting over hardwood floors. We have used a drum sander and edger and we're ready to refinish. This is the most helpful video I have watched at youtube! Blessings to you!
@ceetheninja1 I agree. I've looked a so many but this video really showed the steps in between. I would like to know drying tines in between sending tho
Realmente se puede limpiar con trapo húmedo si voy a aplicar un poliuretano en base de aceite. I can wipe with water if I’m going to use polyurethane oil base .
I have seen soo many videos about how too, and this one was by far the best one.
i used same techniques and have amazing results.
thank you ......
What brush applicator is he using? Do you know? And does he sand at the end ?
@@briceschwartz407 I think he used this one: www.homedepot.com/p/Linzer-10-in-Lambskin-Pad-with-Block-10-in-Lambskin-Floor-Applicator-Refill-Pad-w-4-ft-Wood-Ext-Pole-with-Metal-Tip-HD11001-HD11002-RP548HM4800/315857773
This video is good! I wish I had seen it just a few hours earlier. I just finished my first coat of poly and came up to watch TH-cam to unwind, and the explanation in this video about not being afraid to press hard on the applicator would have helped me. It _will_ help me with my second coat.
Thanks for this video I believe it will help me more than any other tutorial I have seen and I have watch hours. No one showed how much material was used and no one said to use heavy pressure on the applicator. Thanks again.
Thank you for sharing all the excellent tips especially clean lambswool with tape a couple Fuzzy's in your polyurethane can really mess up your day you can tell you take a lot of pride in your work with the results you get have a great day
You guys are freaking awesome looks like you don't have to buff .that's skill right there .
Nice Job! I like how you keep it simple
I use tack clothes to clean the hardwood floor before doing any polyurethane and mineral spirits after that on the hardwood and let dry. . Everything else I do the same as you, but I also clean the ceiling, above doors, windows, window aprons, anywhere there may be dirt or dust. Cleanliness. I also use a paint tray. and set my gallon of poly on plastic or a cardboard for dripping or spillage as it can occur.
Me too, good point.
Thank you soo much! Best video I found.
This is so helpful!! Thank you so much for posting this!!!
thats a great idea with the tape. keep those lint off. never thought about it
Thank you so much, sir. Your videos are truly helpful.
Great video did something similar but a slight variation your shoes Sal Flores for hardwood floors great idea I’m gonna do that from now on when I do hardwood floor’s again thanks for the idea😄
Wow your hands hand with a pole that’s a lot of work Sal.
such a soothing voice!
Awesome job, forget any haters here. The haters only talk trash then try to copy you.
Very nice. We did refinishing on our floor too, using polyurethane
Parks pro finish is the best product for finishing floors I have found. 3 coats is all you need. Home Depot.
Huge help, thank you & well done video👍👍
That is exactly the way I finish floors also. Between coats I simply drop the lambs wool into the can of varnish I am using. Thank you for the video.
Good video for applying finish. The amount of water you used to clean the bare wood floor was bound to raise the grain. Even a damp rag will raise grain on bare wood.
What that means.?
Great video! Thank you very much!
I just used this same poly then read the can to see how long until it dried and it said not recommended for floors and to use the floor finish of that brand found this cause I was wondering how bad of a mistake I made assuming it doesn't matter
How to get debris out after 1st coat has dried? Bad lighting and dark floors caused me not to see any of it 😢
Did you have to put a conditioner on floor before staining
Great video and job!
I wish I came across this video before I started!
It's tough to see hairs and debris on dark floors in a dark room. Even with tripod lighting I miss these things.
I agree this is a great full explanation video thanks
a really nice job compliments
If I only buff the floor (100-150 sandpaper) can I do the same process to paint the floors?
I used the same product you did in this video. After 4 weeks I removed it because the strong smell. Is normal that long?
Says right on that can, not recommended for floors. Varathane Ultimate poly is not for floors. They have different mixture for floors. I made the same mistake had to re-sand the floors
Hi Sal! You gave me the confidence to use a belt sander! Excellent sanding instruction in video 1. I watched the finishing video.... so I understand don’t go thick and use pressure on the applicator to push it in. Light sanding between coats vacuum and tack or damp wipe. After second coat you closed by saying sand with 150 grit? So should I add a 3rd coat, if not why the sanding after second coat? Thanks again!!!
I've seen this question on here a few times. Since he used an oil-based stain, it calls for two coats, but it is OK to apply three. If you apply three coats, most polyurethanes do not require sanding between each coat, but it is good to sand before the last coat with sandpaper between 150- to 220-grit.
He was just repeating himself, he did NOT mean that you have to sand the 2nd coat. If you did sand the 2nd coat, you should apply polyurethane same way he did the 1st and the 2nd.
What is that Solvent Called??To clean the Wool Lamb?Thank you
To all those that are getting ready for doing a second coat… BE CAREFUL SANDING!!! I had to remove the first coat after over sanding, as it would show scratches through. Super pain in my ass. 220 grit is recommended, and go very lightly.
Interesting. I was told to Not apply pressure during application, as it will force air bubbles into the poly.
Is it the mineral spirits that prevent this?
You’re amazing!! Thank you
Very nice sir, what you called that using polishing piece of rag with handle like roller? Thanks a lot for tutorials and god bless you.
It called Goat skin, you buy from any hard wood store, like Lowe’s or Homedepot
@@jayadrian4239 Thank you
Is 2 coats enough ?
Did you say the last step is sanding again ???
Thx very much !
Thank you for posting!
How long does it take for the stain to dry on the floor
When I do this, I wipe the bare wood with mineral spirits. Bare wood and water is not a good idea. I like how they prep the pad with tape to pull up loose fuzz, I’ll do that next time
Exactly… If you are using an oil based polyurethane you never want to use water and always mineral spirits. The biggest issue is that the water will raise the grain.
@@Reefdevil on a floor I can see how it might be a pain, but water will pre-raise the grain so you can lightly sand it off before finishing. Of course make sure it dries completely and then come back with mineral spirits.
Why do others use water popping? Is that just for staining?
Is it ok to use wood glue as sealant before applying water-based glossy varnish (maybe polyurethane) on wood floor? Or you can apply the varnish directly and then sand the floor with #1000 grit or higher for a smooth finish?
@@csraln6748 don’t touch anything and call a professional
Those floors look beautiful. How long did you wait until you added the second finish coat? Thanks.
Read the can. Don't go by others. Typically 4 hours.
Hello man.
Nice job
How long takes to dry up the first coat??
4 hrs
Perfect job #1 the best !! thank you !!!
I pay someone and they did a horrible job theres a few bubble 1 size looks like it have to much polyurethane looks thick and the other side dont look as shinning how can I fix ? Can I sand it without damaging paint on wood?
Good job you guys!
Nice job, Sal! I just found your video, and it is very helpful. One question though. It seems that you used the Varathane "interior finish" ultimate polyurethane on your floor. The label on the can recommends that the "interior finish" should be used on furniture, time, etc inside a house, but not for the hardwood floor. I know a lot of people did use the "interior finish" on the hardwood floor anyway. Just curious how durable the finish on your hardwood floor is after two years. Thanks.
Good question
Isn’t the best way to use buffer machine ?
What black rubber gloves are those?
Good job looks great
Just going to tell you right now for everyone watching this video if you use the exact same can of polyurethane that he is using on hardwood floors... read the whole back of the can first because it says to use a specific kind of poly made by the same brand that is for wood floors, that is not for wood floors. Read the damn can. This is a general poly, not made for wood floors. Sure it can be used, but Varathane makes their own specialty polyurethane for WOOD floors.
why the mineral spirits?
What about clear coat ?
Hello: Are you using oil or water based polyurethane? Thank you!
Never use water based, it will not hold up.
Hey Sal how much do you charge per sq ft? And great job by the way. The only thing I didn’t see which I come across when I’m sanding floors is that there are some corners that that small sander can’t hit in Closets etc. This is what I use a hand sander whether it be a square one or a belt sander to reach in areas that those big machines plus the small rolling sander can’t hit.
Do you use a new applicator for each coat or can you use the previous applicator if you seal it tight in a plastic bag and take the air out?
oil based poly will dryout...use mineral spirits when use done to clean it
I polyurethaned some faux beams I made from drywall that I painted with latex and then gel stained...when I purchased the polyurethane I chose satin...in order to give added protection I applied it very heavily...it came out extremely high gloss, the shiniest gloss I’ve ever seen....unfortunately I wanted satin, or a flat finish...I tried hitting it with steel wool, and even comet to reduce the glossy sheen...but that doesn’t work ,because of how rough I made the beams...is there any product you know of that I can go over the glossy urethane with in order to make it duller looking or flat looking?
I'd try liquid sandpaper. Do it in a test spit first. It dulls the finish
microfiber mop is good for applying poly?
Great video thank you
Will that wool applicator produce bubbles in the finish?
Based on how he is applying the polyurethane, it may cause bubbles. It is best to drag the polyurethane; pour a line and drag it, and then pour another line on the wet edge and repeat. He is doing more of a mopping motion.
I also recommend not wiping the floors down with water, rather mineral spirits. Water, denatured alcohol, or a 50/50 mix of each is best for stain, specifically dark stains. Application of mineral spirits is best used as a pre-application before polyurethane. The use of mineral spirits is also very beneficial when applying water-based polyurethane over an oil-based stain, after it is dry. The use of mineral spirits better ensures that white patches do not form after application of water-based polyurethane over oil-based stain.
@@pound6599 Wow, thank you for the very comprehensive explanation. That's very helpful. Duly noted to use mineral spirits. I will definitely try that.
Do you have to sand between poly?? Guys I hired put two coats within an hour and then next day put final..
Thank you very much
Thank you Thank you...
Thank you for sharing, going to Home Depot
thank you sal
How long shoul i tweat on the staining pad?
I read from supposedly hardwood floor expert. And that is to never use lambs wool brush applicator. So definitely I am confused. Just looking for best way to avoid bubbles. Thanks
He cleaned the lanolin off the natural skin. An important step NOT to miss if you use wool applicators.
Always use a lambswool applicators. Never roll. Rolling incorporates air. I'm not agreeing with this guys technique but yes to lambswool.
@@cjones22p Yes. I do not agree with his technique, as well. He is going over it too much. He has to pull the polyurethane, add another line and pull, etc. But, if his way worked, then who I am to tell him different....
is that semigloss
Whats the purpose of sanding after the 1st poly application? And what happens if u dont sand after the 1st poly application?
It’s pretty much just so it smooths out any uneven spots in the first coat and so the second coat can adhere nicely to the first one
Just found your videos!!! I want to sand down my paint- stained hardwood floors that were never varnished...just raw hardwood planks and has many gaps between planks...any advise on how to approach this? Any advise is welcomed
Water based poly or oil based?
Oil gives it a better look. More depth
Nice job
What did you use to clean the pad?
It’s call Mineral spirits. You can find it at the painting isle of any Home Depot.
Is that satin semigloss or gloss
Most use satin. Semi-gloss and gloss will show more imperfections.
Thank u for this
Buen trabajo, nice job
Thank you
Thank you - love
Wow amazing
Thank u so much!!
You can also try to 20 grand or 330 grit on hardwood floor Polyurethane between coats.
is it necessary? just coating 2 or 3 times wont work?
No mechanical sanding and buffing?
Watch the first video mate 🤙
Hello Sal and everyone reading this comment. I need help with a problem I have after applying the same Finish Coating, when it dries the resul is not smooth in same areas, it is rough and looks like cracking. I don't know what is causing this problem. Can any one help. ???
Cheers!!
It could be your technique and how even the polyurethane is spread.
I have same problem - I put it on too thick. It's been two days and those areas are still soft. I may end up scraping it off and sanding then re-applying.
So as a floor professional don’t use water or mineral spirits to wash the floor it’s completely unnecessary and if you miss a spot you will see it. I also wash my lambs wool in the washer and then dry it to remove any fuzz, it works a lot better. Also avoid products at big box hardware stores buy a decent quality floor finish.
Nope. You're doing this wrong if you apply water to bare wood. Water make the wood pore open up and end up needing to be sanded again befor the poly aplication. Vaccum and tack cloth the area and use mineral spirits to dampen a rag if you must.pleas folks do your self a favor dont use water on bare wood.
200 grit between 1 and 2 coat
Deme trabajo xfa
How long takes to do the 2nd coat??
Great
Every step... patience.
Every one is saying to use buffing between coats ? And you don't use it and still looks great how come?
The sanding he does between coats accomplishes a similar goal. I'm guessing since this is a diy tutorial for people to do at home he's not going to use a buffing machine since most don't have access to one.
That's the wrong Poly...Varathane makes a Floor Finish "High Traffic Formula" specifically for floors.
That Varathane finish is not for floors.
Seems like he put too thin of a coat of the poly on the floors and worked it too much
Cant you just mop with a clean mop instead of on your hands and knees wiping???
lol a professional would use a Vacuum with a floor wand
As someone who does this for a living I admire anyone who attempts this without the proper tools. Do me a favor buy a respirator with charcol filters next time you do a coat of poly. Wearing a Covid mask will not protect you
I use tape like that to get link off my clothes lol
He's doing everything wrong he didn't even use sealer before the Poly .
You are wrong
Dm me I can help edit the videos for you!!!