LINK to INTERNAL HANDLEBAR INSTALL KIT: rushbikes.com/shop-2/handlebars-controls/cables/internal-cable-kits/internal-throttle-brake-conversion-cable-kit-07-17-softail/
Riverside washer video that's awesome how you show step by step how to do it that's pretty awesome so I just want to say thank you for Fresno California God loves🎉🎉🎉
much better quality than the Exile inner throttle, too bad it is so much longer, I have to shorten the handlebars further and shorten a bit of the part that goes into the handlebars
These fork inlets are made by Hawg Halters aka HHI which are used in conjunction with their raked triple trees. Raked trees and shortened forks are necessary when doing lay-frame swing arm setups. HHI trees allow the forks to screw in from below, hence, a side air inlet is required for air ride. If you are running front air ride without lay-frame, then a rake is not needed and the inlets will be located on top. These inlets are included in the Air FX Air suspension kit. Here is a link: rushbikes.com/product-category/suspension/air-ride/air-ride-kits/softail/
That’s a good question, and my answer would be loctite is not necessary as the internal throttle on my chopper hasn’t had any loosening issues and it’s been over 7 years since that install. If you do decide to use loctite, use blue and an extremely small amount. The Allen head set screw is very small and loctite can result in stripping that set screw in the event you ever need to service the throttle line.
To make a perfect cut on the handlebar you take a ruler or tape measure from the end of the bar, measure in 4.5 inches and make a multiple reference marks around the circumference of the bar. Wrap a piece of tape around the bar to reference your cut line. Secure your handle so it doesn’t move during your cut. I used 3/8th - 7/16th drill hole
If you are talking about a clutch cable through the bars? No,too many turns. The hydraulic conversion isn’t that difficult. I’ll post a link to the part list on Monday
LINK to INTERNAL HANDLEBAR INSTALL KIT: rushbikes.com/shop-2/handlebars-controls/cables/internal-cable-kits/internal-throttle-brake-conversion-cable-kit-07-17-softail/
Another great video... this makes the front of the bike look so much cleaner and sleek.
Riverside washer video that's awesome how you show step by step how to do it that's pretty awesome so I just want to say thank you for Fresno California God loves🎉🎉🎉
This is the video I have been looking for. Thank you!
Yeah man, I can’t believe no one has done a video on this yet. Not a legit one at least. I’ll post a link to this kit next week.
Great video and teacher🍻
That was AMAZING! Great video.
Thank you!
Man I wish you guys had a shop in AZ. I would take my bike to you guys on the time
Email sales@rushbikes.com and let us know what year, make and model you have. We may be able to offer you a pre wired handlebar kit.
fantastic video
much better quality than the Exile inner throttle, too bad it is so much longer, I have to shorten the handlebars further and shorten a bit of the part that goes into the handlebars
Email me if you have any questions. Chances are I’ve run across the same issues and found some answers
Can you please tell me Who makes those fork extensions for the air ride? Tanks for the Great video
These fork inlets are made by Hawg Halters aka HHI which are used in conjunction with their raked triple trees. Raked trees and shortened forks are necessary when doing lay-frame swing arm setups. HHI trees allow the forks to screw in from below, hence, a side air inlet is required for air ride. If you are running front air ride without lay-frame, then a rake is not needed and the inlets will be located on top. These inlets are included in the Air FX Air suspension kit. Here is a link: rushbikes.com/product-category/suspension/air-ride/air-ride-kits/softail/
Thanks for the video.
No problemo, thanks for tuning in
Is loctite not needed on the bolt that clamps the throttle cable ? Any concern of it vibrating loose ?
That’s a good question, and my answer would be loctite is not necessary as the internal throttle on my chopper hasn’t had any loosening issues and it’s been over 7 years since that install. If you do decide to use loctite, use blue and an extremely small amount. The Allen head set screw is very small and loctite can result in stripping that set screw in the event you ever need to service the throttle line.
How did you get a perfect cut with a grinder. I'm worried it will be at a weird angle. Also, what size holes did you drill?
To make a perfect cut on the handlebar you take a ruler or tape measure from the end of the bar, measure in 4.5 inches and make a multiple reference marks around the circumference of the bar. Wrap a piece of tape around the bar to reference your cut line. Secure your handle so it doesn’t move during your cut. I used 3/8th - 7/16th drill hole
Do you have the link for the softail 2005 kit?
I’ll be posting the 2007 down (5-speed kit) soon. Email sales@rushbikes.com for assistance
Do you sell all the needed parts as a kit?
Yes, link is in the comments above.
Is it possible to route a cable clutch set up thru the bars? Would it function correctly?
If you are talking about a clutch cable through the bars? No,too many turns. The hydraulic conversion isn’t that difficult. I’ll post a link to the part list on Monday
Only hydraulic clutch