Thanks a ton for this... very informative! Lost the X590 drive belt last night out in the middle of our remote lake property and had to do this out in the field with no hydro for the 54" deck, forward/reverse drive, or power steering. What a joy that was LOL.
If someone wants to prolong the life of the pulley bearings, they can be serviced. I remove the pulley and from the top side, use a sharp pick to pull up the seal. Have to be gentle with it. I clean dirt out with compressed air and some spray, then pack bearing with high grade high temp wheel grease. Then place seal on top of grease and seal will snap back in place.
It is a lot easier on your back to take the steering arms off from the front. A 15mm wrench and a 17 mm socket are all you need. Also, that bar that you removed is not necessary to remove to get the new belt on. If you are just replacing the belt it is only necessary to undo the spring on the double pulley pivot arm not take both pulleys off, just the outside one. Thanks for your time and effort for making the video.
Hey brother! Holy smokes ...I came to learn about the belt and see you have the "Grading Blade"!!! I still have mine from. The LT160 i had. Have been looking for what newer model this kit will fit on! A shame to throw it away!! Thanks for the video! Ciao! God bless!
I need more info on location of the transmission drive belt tensioner spring.i am going to attempt replacing it myself. Do you have a picture of it in place?
Is my new trans belt supposed to be turning when the parking brake is engaged? It drives fine with power so I dont think it is loose. Maybe too tight? Its the right size.
thanks my front pulley just gave out on me and I gotta replace it. Its a shame they 1) made the pulleys plastic and 2) made that front pulley so you have to remove the bracket. If they were going to make piece out of plastic they should have made it a 5 minute replacement part.
my deere d105 barely moves forward or reverse. at times it will start off slow then get up to speed after a few seconds then is slow again. the transmission is quiet and doesnt make any strange sounds.. i thought i had a loose belt but that wasnt the issue. would you have any suggestions? ty
Hey crazy dirt i just picked up a john deere 180 lawn tractor. I'm having a difficult time getting a belt for my trans drive belt the longest one? Do you have any leads on where i could pick one up? The original belt measures 86.50---86.625. I put a gates 6886 which is 86.0 in length but is slightly tight because the clutch dosent work right. The book i have calls for a m73223 but its way to short? Any help would be appreciated...James
Hey James, Yeah the 86" Gates would be a bit tight. It looks to me like a A85K v-belt should fit. The specs on that belt should be 87" long, 1/2" wide at the top (widest part of the V) and 5/16" deep.
Crazy dirt i have a question on checking the transmision fluid on this john deere 180? Is there a spot on the case where to check for proper level of fluid? I have a manual trans not the hydrostatic. Thanks James
James Klimowicz No I don’t think there is a fill or drain on it because (I think) the manual trans uses bentonite grease, as opposed to a gear oil. Please double check that lube spec. before servicing it in case I am wrong.
James Klimowicz You got me wondering about that now. Just looked it up, if it’s the Peerless 800 trans that you have, the book calls for 30 Oz. of bentonite grease, Peerless part number 788067B.
@@CanadianDirt That great any ideas how to find out exactly what type of transmission it is? Ill look through the book i have but its not the best? You think there should be a tag or some identification on it somewhere?
Crazy dirt your correct on the peerless trans. numbers on the top of the tag are 801 039 bottom numbers on the tag are 6002 4499. Talked with the guy who i got the tractor from and this makes sence to me now why its leaking gear fluid he added a few ounces to the trans? Why he did this not sure but he drilled and tapped a hole in the case? My question is how do you think this will affect the trans? It shifts great no issues at this point? Should i add some of the recommended grease? James
Yep, that may be, but when I’m the one making the videos and not monetizing them with any ads, I get to talk about the weather, my dog, or even my armpit. Creator’s prerogative!
Thanks a ton for this... very informative! Lost the X590 drive belt last night out in the middle of our remote lake property and had to do this out in the field with no hydro for the 54" deck, forward/reverse drive, or power steering. What a joy that was LOL.
If someone wants to prolong the life of the pulley bearings, they can be serviced. I remove the pulley and from the top side, use a sharp pick to pull up the seal. Have to be gentle with it. I clean dirt out with compressed air and some spray, then pack bearing with high grade high temp wheel grease. Then place seal on top of grease and seal will snap back in place.
You’re absolutely right, and this would actually be a good application for it where the bearing is integral to the sheave.
It is a lot easier on your back to take the steering arms off from the front. A 15mm wrench and a 17 mm socket are all you need. Also, that bar that you removed is not necessary to remove to get the new belt on. If you are just replacing the belt it is only necessary to undo the spring on the double pulley pivot arm not take both pulleys off, just the outside one. Thanks for your time and effort for making the video.
Thank you Rudy.
-- North Central Florida
Hey brother!
Holy smokes ...I came to learn about the belt and see you have the "Grading Blade"!!! I still have mine from. The LT160 i had. Have been looking for what newer model this kit will fit on! A shame to throw it away!!
Thanks for the video!
Ciao! God bless!
"I am the master of the socket sizes" Lol. Your video helped me fix my problem, Thanks!
Thanks Doug, glad it was a help.
60-65 degrees F is a little warm? That’s like hot chocolate and marshmallow weather where I live 😂
It fits as it should
My lx280 just stopped moving forward reverse and parking brake won’t work. I wonder if it’s the pully? Belt is old but still turning
Great video thanks 👍
Thanks Mark!
Do you have a video or instructions to replace the transmission belt tensioner spring on a John Deere model z335e?
awesome video
I need more info on location of the transmission drive belt tensioner spring.i am going to attempt replacing it myself. Do you have a picture of it in place?
Is my new trans belt supposed to be turning when the parking brake is engaged? It drives fine with power so I dont think it is loose. Maybe too tight? Its the right size.
thanks my front pulley just gave out on me and I gotta replace it. Its a shame they 1) made the pulleys plastic and 2) made that front pulley so you have to remove the bracket. If they were going to make piece out of plastic they should have made it a 5 minute replacement part.
At the 7 min mark you should have been able to get away with just remove both tie rods from steering sector
I wish that was the case but it wasn’t on that tractor.
Can you list the John Deere part numbers for the pulleys and the belt
my deere d105 barely moves forward or reverse. at times it will start off slow then get up to speed after a few seconds then is slow again. the transmission is quiet and doesnt make any strange sounds.. i thought i had a loose belt but that wasnt the issue. would you have any suggestions? ty
How many hours are on your tractor?
@@CanadianDirt 220
@@healthyamerican I would start by inspecting the driven pulley on the transaxle, especially if you have a variable pitch pulley on that unit.
Hey crazy dirt i just picked up a john deere 180 lawn tractor. I'm having a difficult time getting a belt for my trans drive belt the longest one? Do you have any leads on where i could pick one up? The original belt measures 86.50---86.625. I put a gates 6886 which is 86.0 in length but is slightly tight because the clutch dosent work right. The book i have calls for a m73223 but its way to short? Any help would be appreciated...James
Hey James, Yeah the 86" Gates would be a bit tight. It looks to me like a A85K v-belt should fit. The specs on that belt should be 87" long, 1/2" wide at the top (widest part of the V) and 5/16" deep.
@@CanadianDirt I appreciate your help crazy dirt i will try to get on of these belts
@@CanadianDirt Crazy dirt just wanted to get back with you, that belt worked out perfectly... Thanks again for your help....James
James Klimowicz Thanks James, glad to be of help.
That’s a good job but would have been easier to pull the steering wheel up I think just one nut to take off
Thats the way it's done.
My steering wheel might as well have been welded onto the fuckee I did this and it was easier than taking that bitch off my 300r tbh
You sound like ALEX LIFESON OF RUSH THE ROCK BAND.
I never noticed this but after rewatching some one of his interviews, you’re right. Must be a Canadian thing :)
How many hours were on this machine?
Around 500
If I was to swap the two drive pullies on my john deere l111 mower will it drive faster just need a little more top speed not for mowing though?
Changing pulley ratios on hydrostatic driven components is not really recommended as the stock ratio is part of an engineered system.
Does this work on a John Deere LT166
Number of the belt please
Crazy dirt i have a question on checking the transmision fluid on this john deere 180? Is there a spot on the case where to check for proper level of fluid? I have a manual trans not the hydrostatic. Thanks James
James Klimowicz No I don’t think there is a fill or drain on it because (I think) the manual trans uses bentonite grease, as opposed to a gear oil. Please double check that lube spec. before servicing it in case I am wrong.
James Klimowicz You got me wondering about that now. Just looked it up, if it’s the Peerless 800 trans that you have, the book calls for 30 Oz. of bentonite grease, Peerless part number 788067B.
@@CanadianDirt That great any ideas how to find out exactly what type of transmission it is? Ill look through the book i have but its not the best? You think there should be a tag or some identification on it somewhere?
James Klimowicz look for a tag or cast-in-place number on the side of the case.
Crazy dirt your correct on the peerless trans. numbers on the top of the tag are 801 039 bottom numbers on the tag are 6002 4499. Talked with the guy who i got the tractor from and this makes sence to me now why its leaking gear fluid he added a few ounces to the trans? Why he did this not sure but he drilled and tapped a hole in the case? My question is how do you think this will affect the trans? It shifts great no issues at this point? Should i add some of the recommended grease?
James
Can you list the part numbers for the belt and two pulleys please? Thank you
Anthony Huemann the belt will be a M144044. Sorry I don’t have the pulley numbers at the moment.
@@AWoodworkersLife Thank You!
I just changed mine today, v-pulley is AUC11238
Nice work😁
Dude we want to put belt on zero turn nobody cares what temp it is
Yep, that may be, but when I’m the one making the videos and not monetizing them with any ads, I get to talk about the weather, my dog, or even my armpit. Creator’s prerogative!