I found one of these - but with the pencil missing - in a handful of small woodworking bits I inherited many years ago. I asked a few people what it was but no-one knew. Now I shall have to make one for myself! (The one I inherited also had a little round spirit bubble in the top.) Domo arigato!
go next step. Drill second hole between center and stop or one quarter to three quarters stop to stop to 'quarter' a board. drill a third hole in the other half at one third stop to stop to 'third' a board.
Do you notice that when you turn on, and especially when you turn off the drill, does the speed increase? This is because the drill is not working at its nominal power. You should actuate the trigger with a seal at its maximum travel and place an extra switch on the machine frame. Even the perforations are going out more accurate. Greetings from Argentina!
Actually you induce error by turning the peace for 180 degree, if first center punch is not in the middle precisely! What you should do is drill first hole through work peace and bottom helping peace, than move both by some offset and with pin connecting them, than drill second hole on work peace, than offset only work peace and align it with pin...
One problem: The center line that is placed before punching a guide hole, must be exact, otherwise the block will not line up when turning it. Now what?
I think the glue just added a bit more resistance since the hole was a bit on the large side. The glue didn’t stick to the pencil but made the hole a bit smaller.
![[DIY] How to make a center marking gauge / Make your own special tool / HOMEMADE / WOODWORKING](http://i.ytimg.com/vi/FEhqtsbuVow/mqdefault.jpg)
![[DIY] How to make a center marking gauge / Make your own special tool / HOMEMADE / WOODWORKING](/img/tr.png)
![6 Practical Drill bit Sharpening Hacks !!! [Subtitle]](http://i.ytimg.com/vi/dpPmYYexQJ8/mqdefault.jpg)
If you find any unauthorized reproduction of the JSK-koubou video, please report it to me.
Thank you.
JSK-koubouビデオの無断複製を見つけた場合は、報告していただけると助かります。
Mind blown. That trick to get the outside holes to be equally spaced from the center was genius. Thanks.
Simple but not easy. It’s needed accurate tools and good skills. Good job!
It would have been nice to have a center finder when making the center finder. Beautiful work as always!
LOL
Nice! You could also attach a hardened steel tip to scratch the center line.
動画で使用したシャーペンはこれです。
amzn.to/2WcuWQ9
You, my friend, are a genius!
Toujours aussi agréable
De vous voir faire
Merci de partager vos astuces
So simple, efficient, cheap, but not from a simple of mind ;-) and what amazing press set (by yourself indeed)
I made a center marker for an experiment saying, "Is it possible to make an accurate center using a drill stand?"
精度が高いので、落ち着いて観ています。素晴らしいですね！
0:48...you need the center finder to help make the center finder...
Great job! I think I just might make one of these... Thanks for posting!
Domo arigato, sensei. Your videos are an oasis of zen in an otherwise noisy TH-cam
I found one of these - but with the pencil missing - in a handful of small woodworking bits I inherited many years ago. I asked a few people what it was but no-one knew. Now I shall have to make one for myself! (The one I inherited also had a little round spirit bubble in the top.) Domo arigato!
Very good 👍
You are genius! Good work!
Fantastic work, dude! Really well done! 😃
Simple and perfect.
sensacional!!!🤌👏👍
Very good.
100% perfect..............and easy
Да, классная штука!
Bravo Bravo ..
Very Good!
Good job bro
Muito bom parabéns!
Thanks verry nice
PERFECTO COMO SIEMPRE,SALUDOS.
go next step. Drill second hole between center and stop or one quarter to three quarters stop to stop to 'quarter' a board. drill a third hole in the other half at one third stop to stop to 'third' a board.
Thanks Koubou ...
Bitte alle Maße im Video einblenden um es leichter nachbauen zu können! Danke!
Do you notice that when you turn on, and especially when you turn off the drill, does the speed increase? This is because the drill is not working at its nominal power. You should actuate the trigger with a seal at its maximum travel and place an extra switch on the machine frame. Even the perforations are going out more accurate. Greetings from Argentina!
センターファインダーを作るためにセンターをファイン度しなければならない矛盾
hello. thanks for video! where can I see the making of vertical saw statement ?
過去の動画で紹介しています
th-cam.com/video/M1xYKw5FP-0/w-d-xo.html
@@jisakukobo thanks a lot!
but can it be used to find the centre of the universe?
I find that when you turn the centre finder round the other way the lines don’t line up...
correctly! he induce error by that 180 turn
Actually you induce error by turning the peace for 180 degree, if first center punch is not in the middle precisely! What you should do is drill first hole through work peace and bottom helping peace, than move both by some offset and with pin connecting them, than drill second hole on work peace, than offset only work peace and align it with pin...
👏👏👏👍👍👍
One problem: The center line that is placed before punching a guide hole, must be exact, otherwise the block will not line up when turning it. Now what?
Who was the original inventor? Unable to find the info. I know that this was invented by someone long ago
👍
🖒🖒🙌🙌
You strike me as the guy that can complete most tasks but do so in a painfully slow manner
why the glue on the pencil?
I think I'm wrongly assuming that you pulled the pencil out after the gluing, but likely the "try" message is before the gluing?
I think the glue just added a bit more resistance since the hole was a bit on the large side. The glue didn’t stick to the pencil but made the hole a bit smaller.
日本 のclip みたいです
Старо как Мир...
А зачем карандаш вклеивать, а потом вынимать?
私は接着していないという事を伝えたかったのです。
木工用ボンドを使った理由は適度な圧入にする目的だからです。
очень долго показываешь мелочь.
в этом стиль
大丈夫。動画づくりを変更するつもりはありません。
very basic do that, but...
Ты когда ногти будешь стричь?