The set up looks quite good now, good job! However, the centre propeller was almost certainly a 3 bladed jobbie! Pictures available are from the RMS Olympic in dry dock and show a 4 bladed propeller. A recent note book found from an engineer shows quite clearly that the Titanic was fitted with the 3 bladed propeller at the time of sailing. This has been quite a controversial point until recently. The good news is that replacements are easy enough to buy if Hachette don't pop one in as an alternative later in the build! Good luck with it! 😉
Curious to see the wyper arms on the Stephenson gear see sawing too and fro - normally these are fixed by gib head keys to the wyper shaft and not independent. They will be either in or out for Ahead or Astern - Pls can you explain? Also correct that in Ahead, the centre exhaust turbine drives its propeller, and in Astern, the centre propeller is idle.
It's a model kit and that Is the way it is assembled, so it's down to the manufacturer of the kit , there is a few things on this model that are not accurate !
Grave error de diseño de la réplica. Los vástagos de las válvulas invaden el camino diseñado para el mantenimiento del motor . Causarían la muerte de los mecánicos de mantenimiento. Fácil de ver .
Going full reverse sealed her fate. If they kept that center screw turning it would have forced water against the rudder,and she could have turned faster
I came across someone selling these Hachette Titanic magazines, (they gave up on buying all 140 issues) I purchased issue 3 that has parts for the one engine and smoke generator, If I'm only interested in building the two engines and driveshafts, props, which other issues do I need to get? Thanks for any help you can offer. Kind regards.
You will need issue 3.5.6.7.10.then all issues from 26 to 40, if that helps your best bet, are to get them from Hachette as you can buy separate issues !
You could try phoneing Hachette Partworks and they will probably be able to get the issues you need but may have to wait for them to come back in stock !
The set up looks quite good now, good job! However, the centre propeller was almost certainly a 3 bladed jobbie! Pictures available are from the RMS Olympic in dry dock and show a 4 bladed propeller. A recent note book found from an engineer shows quite clearly that the Titanic was fitted with the 3 bladed propeller at the time of sailing. This has been quite a controversial point until recently. The good news is that replacements are easy enough to buy if Hachette don't pop one in as an alternative later in the build! Good luck with it! 😉
Yes your right , it should be three blade on the centre propeller, Hachette have got a few things wrong so far such as colours of some parts !
The big cranks on the outboard side of the engines should not move, those arms connect the drive rods to the reversing engines.
"Great!" 👍
Wow, awesome build!
Fantastic buddy looks really nice 👌
Bravo continua così 👍👍👍💪💪👍
Really neet!!! Nice work.
Thank you! Cheers!
Bonjour, superbe, nous en France ne sommes pas encore si loin !
Looks good…👌🏽
Super cool. I hate to be that guy, but it would really benefit from a quiet motor / geartrain. Perhaps something brushless and turning at a lower RPM
Looks brill 👍 just finally got mine engines finished they was a nightmare i hated doing them, so fiddley and awkward
I agree with you a bit fiddley !
Curious to see the wyper arms on the Stephenson gear see sawing too and fro - normally these are fixed by gib head keys to the wyper shaft and not independent. They will be either in or out for Ahead or Astern - Pls can you explain?
Also correct that in Ahead, the centre exhaust turbine drives its propeller, and in Astern, the centre propeller is idle.
It's a model kit and that Is the way it is assembled, so it's down to the manufacturer of the kit , there is a few things on this model that are not accurate !
Pretty cool model the engine room is pretty accurate too bad the turbine room and the electrical engine room isn’t accurate but still a cool model.
Grave error de diseño de la réplica. Los vástagos de las válvulas invaden el camino diseñado para el mantenimiento del motor . Causarían la muerte de los mecánicos de mantenimiento. Fácil de ver .
How'd you do this?!
what issues are them
Going full reverse sealed her fate. If they kept that center screw turning it would have forced water against the rudder,and she could have turned faster
The engines were not commanded full astern in the attempt to avoid the iceberg.
The engines where actually commanded all stop, so no water was being forced against her rudder
There was no iceberg
@@bayerischemotorenwerke5252 There was lmao
@@Robabin no
I came across someone selling these Hachette Titanic magazines, (they gave up on buying all 140 issues) I purchased issue 3 that has parts for the one engine and smoke generator, If I'm only interested in building the two engines and driveshafts, props, which other issues do I need to get? Thanks for any help you can offer. Kind regards.
You will need issue 3.5.6.7.10.then all issues from 26 to 40, if that helps your best bet, are to get them from Hachette as you can buy separate issues !
@@kevinb897 thank you so much!
I got same problem everything to do with engine room has gone wrong
I checked issues I need to start over and too much to pay and early issues are not available
You could try phoneing Hachette Partworks and they will probably be able to get the issues you need but may have to wait for them to come back in stock !
Hi Which parts would you need to buy if you just wanted the engine parts
You will need issues 3. 5.6.7 and 10, then issues 26 to 40. I'm not sure if they are still available, but try Hachette partworks
I wish I can buy this
Just look up Hachette Partworks you can get the Model kit from them !
Great work but omg the noisy motor...
Yes, I know it is noisy, but once it's inside the ship, hopefully, it won't be as bad !
Los brazos de las bielas pasan sobre la pasarela de mantenimiento. Peligro mortal para los mecánicos que circulen sobre ellas . Gran error .
Would you be abke to put these in a model?
Yes, it will eventually go into the Hachette 1/200 scale model of the Titanic of which I'm building !
I've had problems with my engines . I feel like giving up. Unless I get relevant issues to rebuild new ones
I had to take appart one engine because it wasn't turning properly, but all OK now just take your time !
@@kevinb897 I can't take apart because of parts that needed glue
@@kevinvicedomini8745 lol
No entiendo por qué las élises giran en sentidos contrarios..
Link to buy
Hachette Partworks, or Agora models !
Carica altri video