Not in this situation or with this model but after getting an overview from the site, I'm impressed a person noticing a design flaw with a cast-iron that bends under heat and pressure and then goes out on a crusade to design and CNC the part and also produce it for others and make a tutorial so the average skilled consumer can DIY repair a Chinese product that is difficult to get any service for, here in the west. internet repair community at its finest. Well done, cheers from Denmark.
I never add any comment on youtube but i want to thank you for this tutorial ! I just repaired my xiaomiprojector having troubles for the last 8 months thanks to your perfect video. Have a nice day and once more thanks !
Hi Nikos, thanks for the detailed guide and pinpointing the culprit of the vertical line issue. I couldn’t repair the projector myself without your guidance in this video. Thanks again for sharing this rare repair guide.
@@Vic-hl7wm экран был черным, не показывал картинку. Отходил шлейф главный, который с завода прижимается какой то силуминовой пластиной. Со временем из за температур это пластина деформировалась и контакт прерывался. По началу можно было чуть стукнуть, потом надо было просто подождать минут 5 пока прогреется, потом уже ничего не помогало. Пробовал сначала прижимать чем то но не сильно помогало. У него заказал стальную. Уже 3 года полет отличный.
@@akaANUNAKI понятно... в России нет мастерских такое исправить? у меня стекло внутри начало потеть от вэйпа, надо было разбирать и чистить... не одна мастерская не хотела за это браться в штатах, так как у них нет договоров с xiaome! А вообще, 5 лет проработал отлично.
@@Vic-hl7wm тогда вроде не было. А если и были то я не искал. По сути не обращался потому что официально никто сюда не вез проекторы такие и ожидать месяц чтобы сц сказал что ничего не могут сделать не стал. Просто погуглил, наткнулся на мою проблему и решил ее собственноручно. Дешевле и быстрее вышло. Разбирается довольно просто и деталей не много. На счёт запотевания не сталкивался. Там по сути поликарбонат и под ним линза. Разобрать и посмотреть где запотевает и протереть. Либо если поликарбонат отнести на полировку. Если линза боюсь это либо сложный разбор либо замена.
Nikos, thank you for making the plate for me. It was worth every penny. I followed your instructional video step by step, and it worked to perfection. The picture quality is just like when the unit was new.
Thank you for the tutorial and the part it worked like a charm ! This is THE solution to long time boot, vertical lines problems of the xiaomi 4K laser projector.
Hello Nikos Thank you very much for this video and all the work you have done for the repair of the Xiaomi 4K video projector MJJGTYDS01FM and for the new Plate that you have created in laser numerical control with the details of the holes to tap frankly me who am a manufacturer of job I appreciate the work you did,
I had this same issue after some 1.5 years and the boot time for the projector was approx 4 minutes with vertical lines which will eventually disappear in 4 minutes when the projector warms up. I ordered the contact plate from Nikos & it reached India in 16 days. I just followed this video and the repair is quite straightforward, however its not very easy as well. The repair needs Philips head screw driver of various sizes, tweezers, and some plucktrums. There were few difficult places, but otherwise it can be done by anyone with some little experience with electronics. After replacement, the projector works as new and no vertical lines of what so ever. Once again thanks you Nikos...
Hi Nikos, I have finally found the detailed mounting video. I feel more comfortable to do this after having watched this video with the new plate I have received from you. I have 2 questions : do you put alcohol on the cotton bud before cleaning the piece of metal ? Where did you buy the metalic tablecloth. Amazon ? Seems great Thanks again
Thanks for the video, i read about it last night in a forum and wanted to see how complicated it is. It is quite a video, and of course difficult. I don't hsve that problem yet. But my projector when starting is really loud and I hate the sound of it. I thought that were the fans but I saw you changed yours and no differences so, there is not a simple way to reduce the noise from the projector at all, right?
Hi i’ve the fengmi 4k 2021, everything was fine for the last 3 years and today i wanted to change de fastfocus after months without no settings change and i discovered the fastfocus is « broken » it’s not working anymore and the top part of my screen est full blur 😢 do you have any idea what i can do? Best regards and thanks for your help 🙏
I have an old white xiami one and always have the auto turn off issues. And now it just say the fan is not working and turn off automatically, would this be the same issue? Sorry to take your time. Thanks a lot 🙏🏼🙏🏼🙏🏼
Hi Nikos, first of all great work. I very rarely write a comment, but I just had to write one.... YOU ARE AWESOME. Now to my question, are you selling the metal part? I haven't found it anywhere. My projector is now making these white lines. Hope you can help.
got a dead pixel on my Hisense ultra short throw projector lately. lucky the warranty expire next month. A technician supposed to come today but had to reschedule because he said he have never work on one before. I hope i on't see him watching your tutorial to fix my device next week...
I have A300 projectors having the same problem. Your video is a great help to know, i am not savy to do the repair myself. Is anyone in Singapore able to repair for a fee?
Hi i have the 2020 version all working fine and i know there were improvements made like full color wheel and laser temperature monitoring so i think they would of checked out any issues 👍
@@dexter19885 Hi Ive run mine for 50hrs + now and no problem with the 2020 version , bear in mind theres tens of thousands of these out there and most are working fine 👍
@@ebow7964 I just think that if they all have that same metal plate, the issue should be widespread after a year or so. But I'm really interested in the projector - it just seems like a huge risk as the service from the sellers seem to be non-existent.
Hello @nikos do you know any place where we can purchase parts of this projector, i am not having this issue but having issue with color, there is green/purple tint in some scenes with bright light, maybe because of faulty optical engine.
Things like this are what's stopping me from buying a chinese UST projector at the moment (+ the coil whine). You would think one of the designers/engineers would have fixed this plate with the new models but as I've read in your post this doesn't seem to be the case...
Nice work. Quick question as I couldn't make out in the video but can you remember if the fans used standard fan headers? Probably not work the risk of opening it up but wondering if its viable to replace the fans with higher quality ones in an effort to reduce noise.
Τhe noise is not from the fans, i have replaced in mine the fans with silent fans, no difference. The noise is from the XPR module and from the phosphor color wheel.
hi, for the me only teh HDMI ports of the projector is not working. Have you come across this issue before? the projector works fine, but the HMDI ports does not detect the input device. Can you help me with a solution?
Hi! My laser lanp suddenly stopper working today. Worked yesterday. Now there is no image, obviously, but there is sound. Projector is 1.5 years old. Is it the same repair procedure?
I suppose no. I had to replace the curved plate several months ago (successfully) and yesterday my lamp or laser died and now I’m more or less in your situation. In the next days I will dissemble it again and maybe I have more info. Please contact me if you resolve it.
@@gandolfo_, thanks for your reply. I managed to get to the bottom of this - it happens when there is no device plugged into HDMI1. And you have to plug it really hard - any slight cable movement will turn the lamp off. This is annoying of course, but since I don't touch those cables and don't haver any too small kids or animals playing with them - can live with the issue. Still bothers me though.
@@gandolfo_Hello. Don't have any image at all? Or is it barely visible when the lights are off? My brightness is very low (the picture is visible only in the dark), perhaps we have similar problems, did you manage to solve the problem?
Спасибо за видео, Никас! У меня такая же проблема. Вертикальные полосы на половину экрана. 2 вопроса: 1)можно заказать пластину? 2) или нужно менять чип Dmd? Напишите Вашу электронную почту, как с Вами связаться. Спасибо! 1) можно заказать пластину
Great Job, i have a question , I have the Mi 150, it seems the power supply unit in the projector need replacement, do you know where i can find a replacement for it ? Thank you
Hello. Why did you decide that you have a problem with the power supply? I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything), I think that I may also have problems with the power supply
My Projector is not turning on anymore. When turned on it just makes a loud beeping sound and shutdown. I think it is the bend Plate. Where can I get the plate from? Thanks in advance
i think i've read somewhere that some kind of 4k upscaling chip caused this. By disabling something in a menu that coil whine stopped. But i'm not sure where i've read that so i cant find it anymore
the high pitched noise is caused by the color wheel motor spinning at around 5000rpm this cannot be stopped they may be able to dampen the sound with later design upgrades
Hi, thanks for your video. I have a different issue to yours. My projector suddenly stops displaying anything. It displays a black screen with the front light flashing. Do you know what’s the driver ? Thanks !!!
Hello. I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything). Perhaps we have similar problems, did you manage to solve the problem?
Hello. I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything). Perhaps we have similar problems, did you manage to solve the problem?
this might be an illogical question but guys, would you buy the Mi 4K projector again even knowing there is this issue ? If not, which one would you get ? Do the newer version suffer from the same problem ? Thanks!
After 2 years of experience with it, I am not sure I would recommend it: the fans are pretty loud (to replace them, you need to fake the fan speed output), it's very hard to replace the xiaomi chinese android by a generic english android (consequence: some menu and content remain chinese), and finally this issue that seems to happen after 18months of use (the slow bootup or lines). But Picture size and precision is great.
Hi Nikos My projector has some dotted lines and when I shake the projector it boots sometime or it takes a long time to boot. Can you send the plate to India and let me know how I can order one
J'étais curieux puisque j'ai complétement modifié mon vidéoprojecteur led je peux tout réparer ou changer dessus zero obsolescence, mais le laser c'est d'une autre planète
Have you failed to mention if there is a screw underneath the product label in the centre (where the model number and serial numbers feature) purely because i have got to the stage where you disconnect the top and its met with extreme resistance in the middle part of the projector 😤 Many thanks in advance
Hi mate, my projector is starting to fail now... it is not permanent lines and not everything I boot it. But I prefer safe than sorry, is there any webside where I can purchase the piece from you? Thanks 😊
@@projectorjunkies4152 I have send you another one, also from the email I got an automatic answer saying that the email is not longer available, I also tried to sudmit my request to contact you through the email but it stay loading forever mate. So i don´t know if you managed to receive the email at all. Sorry for the trouble :S
To everyone out there facing this problem with vertical lines - try to tap/move a bit main cable in the middle to see if it does not help with the problem (the one being lifted at 7:38 of this video). I have got the better part from Nikos last year, but eventually the problem reappeared. I did dis(assemble) this projector about 20x by now, and currently tapping cable is what fixes the problem for me, and making sure it is not pushed by anything when assembling back. Showing myself the effect of tapping in this video: th-cam.com/video/R2Lueqy-jKI/w-d-xo.html
I have the 2019 version. A week ago the projector started to reboot itself. Now it completely gone off and doesn't power on anymore... DMD Plate problem, or a Power Supply failure? Any ideas? 🤔
Same problem for me also. It can be started after a long gap by switching the power off. Again problem of rebooting starts within an hour of running. Any solution please.
I discovered the problem with mine. It was the power cord. I wasn't using the original one provided with the projector, because of the Chinese plug pattern. I've changed the plug on the original cable and now I'm using it. The projector is now operating flawlessly.
My projector shuts off saying heat sensor issue will shut off in 5 sec to protect itself I live in India can you help me please there I no local service center here
Very good job!!! I have a problem too with my xiaomi mjjgtyds01fm...the video is completely black! The source light is completely death!!!! You think could be the same issue? Wher canci find the replacement? You sell it? Thank you very much. Davide
Update: i just fixed my problem!! A flat cable wasnt blocked and when I opened the pj this made the problem. I'm anyway intersted in your plate. Please can you say me how I can buy It? Thank you davide
Hi everyone, I have a Xiaomi Mi 4K Laser Projector 150" and I'm experiencing an issue where the projector only displays one color after a short time of use. When I first turn it on, the image appears normal with all colors working correctly. However, after a few minutes, the screen shifts to displaying only a single color (e.g., red, green, or blue) and the other colors disappear. Has anyone else experienced this issue? What could be causing it? I suspect it might be related to overheating, a failing laser, or some issue with the power supply. I'm not sure if this could be a hardware problem with one of the lasers or perhaps a cooling issue. Any advice on how to diagnose and fix this would be greatly appreciated. Thanks in advance!
Not in this situation or with this model but after getting an overview from the site, I'm impressed a person noticing a design flaw with a cast-iron that bends under heat and pressure and then goes out on a crusade to design and CNC the part and also produce it for others and make a tutorial so the average skilled consumer can DIY repair a Chinese product that is difficult to get any service for, here in the west.
internet repair community at its finest.
Well done, cheers from Denmark.
I never add any comment on youtube but i want to thank you for this tutorial ! I just repaired my xiaomiprojector having troubles for the last 8 months thanks to your perfect video. Have a nice day and once more thanks !
you are welcome my friend
Hi Nikos, thanks for the detailed guide and pinpointing the culprit of the vertical line issue. I couldn’t repair the projector myself without your guidance in this video. Thanks again for sharing this rare repair guide.
Nikos! Thank you so much for your help. I got the plate from you and installed it with your video. It worked! Slow boot up now a thing of the past!
Just did my repair with the metal repair thing you send... everything now works as new! THX a lot from Russia with love! ))
что у тебя не работало?
@@Vic-hl7wm экран был черным, не показывал картинку. Отходил шлейф главный, который с завода прижимается какой то силуминовой пластиной. Со временем из за температур это пластина деформировалась и контакт прерывался. По началу можно было чуть стукнуть, потом надо было просто подождать минут 5 пока прогреется, потом уже ничего не помогало. Пробовал сначала прижимать чем то но не сильно помогало. У него заказал стальную. Уже 3 года полет отличный.
@@akaANUNAKI понятно... в России нет мастерских такое исправить? у меня стекло внутри начало потеть от вэйпа, надо было разбирать и чистить... не одна мастерская не хотела за это браться в штатах, так как у них нет договоров с xiaome! А вообще, 5 лет проработал отлично.
@@Vic-hl7wm тогда вроде не было. А если и были то я не искал. По сути не обращался потому что официально никто сюда не вез проекторы такие и ожидать месяц чтобы сц сказал что ничего не могут сделать не стал. Просто погуглил, наткнулся на мою проблему и решил ее собственноручно. Дешевле и быстрее вышло. Разбирается довольно просто и деталей не много. На счёт запотевания не сталкивался. Там по сути поликарбонат и под ним линза. Разобрать и посмотреть где запотевает и протереть. Либо если поликарбонат отнести на полировку. Если линза боюсь это либо сложный разбор либо замена.
Nikos, thank you for making the plate for me. It was worth every penny. I followed your instructional video step by step, and it worked to perfection. The picture quality is just like when the unit was new.
Hi, do you know where I can get the plate?
@@spymike8235 You can contact Nikos using the website in the video description. I asked him 3 / 4 weeks ago and I received my plate some days ago.
Thank you for the tutorial and the part it worked like a charm ! This is THE solution to long time boot, vertical lines problems of the xiaomi 4K laser projector.
Dear Nikos, Thanks a lot for the video. Without I was very nervous. And then I found the video and it went smoothly. You rock !
Hello Nikos Thank you very much for this video and all the work you have done for the repair of the Xiaomi 4K video projector MJJGTYDS01FM and for the new Plate that you have created in laser numerical control with the details of the holes to tap frankly me who am a manufacturer of job I appreciate the work you did,
You welcome my friend!
@@projectorjunkies4152 Is the plate still available, having same probem with my A300? Thank
Is this the process of replacing bad pixel?
I had this same issue after some 1.5 years and the boot time for the projector was approx 4 minutes with vertical lines which will eventually disappear in 4 minutes when the projector warms up. I ordered the contact plate from Nikos & it reached India in 16 days. I just followed this video and the repair is quite straightforward, however its not very easy as well. The repair needs Philips head screw driver of various sizes, tweezers, and some plucktrums. There were few difficult places, but otherwise it can be done by anyone with some little experience with electronics. After replacement, the projector works as new and no vertical lines of what so ever. Once again thanks you Nikos...
How did you order ?? I’m also from india and I’m facing issues like it turns off suddenly without any warning
What a MAKER soul! Kudos!
Hi Nikos,
I have finally found the detailed mounting video. I feel more comfortable to do this after having watched this video with the new plate I have received from you.
I have 2 questions : do you put alcohol on the cotton bud before cleaning the piece of metal ?
Where did you buy the metalic tablecloth. Amazon ? Seems great
Thanks again
Thanks for the video, i read about it last night in a forum and wanted to see how complicated it is. It is quite a video, and of course difficult. I don't hsve that problem yet. But my projector when starting is really loud and I hate the sound of it. I thought that were the fans but I saw you changed yours and no differences so, there is not a simple way to reduce the noise from the projector at all, right?
Damn ...what is this 🎼score again, I'm over here nodding my head off😆🎶🎶🎶 BIG orchestra conductor Energy 😁
thanks for your help and the new plate. UST seems to be working again! Did you replace the thermal paste?
I like your style of music 🎶 👌
Hi i’ve the fengmi 4k 2021, everything was fine for the last 3 years and today i wanted to change de fastfocus after months without no settings change and i discovered the fastfocus is « broken » it’s not working anymore and the top part of my screen est full blur 😢 do you have any idea what i can do? Best regards and thanks for your help 🙏
I have an old white xiami one and always have the auto turn off issues. And now it just say the fan is not working and turn off automatically, would this be the same issue? Sorry to take your time. Thanks a lot 🙏🏼🙏🏼🙏🏼
Спасибо, хорошая инструкция. Тоже надо отремонтировать свой проектор.
Hi Nikos, first of all great work. I very rarely write a comment, but I just had to write one.... YOU ARE AWESOME. Now to my question, are you selling the metal part? I haven't found it anywhere. My projector is now making these white lines. Hope you can help.
Same problem here...the first white pixel is appearing on the screen. Where can I get the replacement metal part, and what partnumber is it. KR, Eric
got a dead pixel on my Hisense ultra short throw projector lately. lucky the warranty expire next month. A technician supposed to come today but had to reschedule because he said he have never work on one before. I hope i on't see him watching your tutorial to fix my device next week...
How thick is that thermal pad if you don't mind me asking?
I have A300 projectors having the same problem. Your video is a great help to know, i am not savy to do the repair myself. Is anyone in Singapore able to repair for a fee?
Can the light bulb be replaced?
Hi Nikos ! Thanks for your job ! I sent you a mail cause I need this New plat. Thanks a lot!
Hi Nikos - Do you know if this is an issue on the new Mijia 1S 4K DS02 2020 version at all and whether Xiaomi have corrected this issue? Thanks
I'd also like to know this.
Hi i have the 2020 version all working fine and i know there were improvements made like full color wheel and laser temperature monitoring so i think they would of checked out any issues 👍
@@ebow7964 It seems the issue doesn't arise the first year or so after several hours of use. How much have you used yours?
@@dexter19885 Hi Ive run mine for 50hrs + now and no problem with the 2020 version , bear in mind theres tens of thousands of these out there and most are working fine 👍
@@ebow7964 I just think that if they all have that same metal plate, the issue should be widespread after a year or so. But I'm really interested in the projector - it just seems like a huge risk as the service from the sellers seem to be non-existent.
Thanks for the video. I also emailed you about possibly purchasing the plate. Wondering if you've received it. Thanks!
Hi I need replacement fans (right hand side) as they are starting to fail. Any advice on where I can purchase them?
Hello @nikos
do you know any place where we can purchase parts of this projector, i am not having this issue but having issue with color, there is green/purple tint in some scenes with bright light, maybe because of faulty optical engine.
Where can I get the plate please? Thanks
Things like this are what's stopping me from buying a chinese UST projector at the moment (+ the coil whine). You would think one of the designers/engineers would have fixed this plate with the new models but as I've read in your post this doesn't seem to be the case...
Nice work. Quick question as I couldn't make out in the video but can you remember if the fans used standard fan headers?
Probably not work the risk of opening it up but wondering if its viable to replace the fans with higher quality ones in an effort to reduce noise.
Τhe noise is not from the fans, i have replaced in mine the fans with silent fans, no difference. The noise is from the XPR module and from the phosphor color wheel.
@@projectorjunkies4152 good to know, saves a job. Thanks!
hi, for the me only teh HDMI ports of the projector is not working. Have you come across this issue before? the projector works fine, but the HMDI ports does not detect the input device. Can you help me with a solution?
Hi! My laser lanp suddenly stopper working today. Worked yesterday. Now there is no image, obviously, but there is sound. Projector is 1.5 years old. Is it the same repair procedure?
I suppose no. I had to replace the curved plate several months ago (successfully) and yesterday my lamp or laser died and now I’m more or less in your situation. In the next days I will dissemble it again and maybe I have more info. Please contact me if you resolve it.
@@gandolfo_, thanks for your reply. I managed to get to the bottom of this - it happens when there is no device plugged into HDMI1. And you have to plug it really hard - any slight cable movement will turn the lamp off. This is annoying of course, but since I don't touch those cables and don't haver any too small kids or animals playing with them - can live with the issue. Still bothers me though.
@@gandolfo_Hello. Don't have any image at all? Or is it barely visible when the lights are off? My brightness is very low (the picture is visible only in the dark), perhaps we have similar problems, did you manage to solve the problem?
Спасибо за видео, Никас!
У меня такая же проблема. Вертикальные полосы на половину экрана.
2 вопроса:
1)можно заказать пластину?
2) или нужно менять чип Dmd?
Напишите Вашу электронную почту, как с Вами связаться.
Спасибо!
1) можно заказать пластину
Was any liquid used on the cotton bud when cleaning the component under the plate?
just use IPA to clean contacts and then remove the old heat sink compound and replace with new .
Great Job,
i have a question , I have the Mi 150,
it seems the power supply unit in the projector need replacement, do you know where i can find a replacement for it ?
Thank you
Hello. Why did you decide that you have a problem with the power supply? I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything), I think that I may also have problems with the power supply
My Projector is not turning on anymore. When turned on it just makes a loud beeping sound and shutdown. I think it is the bend Plate. Where can I get the plate from? Thanks in advance
Great video ! Any ideas concerning the high pitch noise by any chance. Do you know by what it could be caused ?
Cheers
i think i've read somewhere that some kind of 4k upscaling chip caused this. By disabling something in a menu that coil whine stopped. But i'm not sure where i've read that so i cant find it anymore
the high pitched noise is caused by the color wheel motor spinning at around 5000rpm this cannot be stopped they may be able to dampen the sound with later design upgrades
Any idea about how to clean an internal dust in the lens?
If we have white dot on screen, this is the same issue and solution ?
Hi thanks for you great job!! Can i buy The platea from you?
great job!
Hi, thanks for your video. I have a different issue to yours. My projector suddenly stops displaying anything. It displays a black screen with the front light flashing. Do you know what’s the driver ? Thanks !!!
Hello. I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything). Perhaps we have similar problems, did you manage to solve the problem?
Hi, I have a Vava that only shows a small amount of light. Any tips on finding a repair company for that?
Hello. I have the same projector, and it shines very dimly (the brightness is very low, you need to turn off the light to see anything). Perhaps we have similar problems, did you manage to solve the problem?
Can you repair a VAVA UST projector?
Hello I have a Xgimi A1 UST that did something odd and I’m not sure if you repair these or can advise? Is there a way to contact you? Email?
Do it fix random rebooting?
Hi Nikos, i also Need the Metal Plate! Can have one? Greetings from Germany
this might be an illogical question but guys, would you buy the Mi 4K projector again even knowing there is this issue ? If not, which one would you get ? Do the newer version suffer from the same problem ? Thanks!
After 2 years of experience with it, I am not sure I would recommend it: the fans are pretty loud (to replace them, you need to fake the fan speed output), it's very hard to replace the xiaomi chinese android by a generic english android (consequence: some menu and content remain chinese), and finally this issue that seems to happen after 18months of use (the slow bootup or lines).
But Picture size and precision is great.
Where do I get this plate ? I’m india !! Whom to contact , pls help me
Hi Nikos
My projector has some dotted lines and when I shake the projector it boots sometime or it takes a long time to boot. Can you send the plate to India and let me know how I can order one
Can you pls reply pls
J'étais curieux puisque j'ai complétement modifié mon vidéoprojecteur led je peux tout réparer ou changer dessus zero obsolescence, mais le laser c'est d'une autre planète
Have you failed to mention if there is a screw underneath the product label in the centre (where the model number and serial numbers feature) purely because i have got to the stage where you disconnect the top and its met with extreme resistance in the middle part of the projector 😤
Many thanks in advance
Thats where I am stuck... what was your solution?
Yes there is a screw under the label at least on my white one.
How can I get wiring schematic or this?
Hi mate, my projector is starting to fail now... it is not permanent lines and not everything I boot it. But I prefer safe than sorry, is there any webside where I can purchase the piece from you? Thanks 😊
you can send me an email to info@projectorjunkies.com
@@projectorjunkies4152 Thank you man, I have sent you an email a few days ago. Have a look when you have a second. :D
Thank you so much!
@@MrJunglahot My friend i can not find any email from you. Can you resend it?
@@projectorjunkies4152 Of course, I just did. Take care :D
@@projectorjunkies4152 I have send you another one, also from the email I got an automatic answer saying that the email is not longer available, I also tried to sudmit my request to contact you through the email but it stay loading forever mate. So i don´t know if you managed to receive the email at all.
Sorry for the trouble :S
To everyone out there facing this problem with vertical lines - try to tap/move a bit main cable in the middle to see if it does not help with the problem (the one being lifted at 7:38 of this video). I have got the better part from Nikos last year, but eventually the problem reappeared. I did dis(assemble) this projector about 20x by now, and currently tapping cable is what fixes the problem for me, and making sure it is not pushed by anything when assembling back. Showing myself the effect of tapping in this video: th-cam.com/video/R2Lueqy-jKI/w-d-xo.html
looks like heatsink grease on the dmd chip....if its dried out could cause the overheating and warping issue.
Привет всём владельцам такого проектора, подскажите где вы берëте зап части на него, сгорела плата.
I would like to purchase the metal plate. Please contact me for more information.
Is it because of too much heat that cause the metal to bent?
yes, and the pressure of the cooler.
It baffles me how a global brand can put out a product with such amateurish defects.
I have the 2019 version. A week ago the projector started to reboot itself. Now it completely gone off and doesn't power on anymore... DMD Plate problem, or a Power Supply failure? Any ideas? 🤔
Same problem for me also. It can be started after a long gap by switching the power off. Again problem of rebooting starts within an hour of running. Any solution please.
I discovered the problem with mine. It was the power cord. I wasn't using the original one provided with the projector, because of the Chinese plug pattern. I've changed the plug on the original cable and now I'm using it. The projector is now operating flawlessly.
good job...
My projector shuts off saying heat sensor issue will shut off in 5 sec to protect itself I live in India can you help me please there I no local service center here
I am facing similar issue unit shut off saying fan abnormal. What’s the fix for this ?
I have a problem with my project . It work 10 to 12 min picture will be off but sound is working. Can you help me.
@Bijaya, what version is your projector ?
Very good job!!! I have a problem too with my xiaomi mjjgtyds01fm...the video is completely black! The source light is completely death!!!! You think could be the same issue? Wher canci find the replacement? You sell it? Thank you very much. Davide
Update: i just fixed my problem!! A flat cable wasnt blocked and when I opened the pj this made the problem. I'm anyway intersted in your plate. Please can you say me how I can buy It? Thank you davide
@@davidefr hi, im facing the same issue as yours. No video. What do you mean by cable wasnt blocked? what did u do to fix it?
thanks in advance =)
@@bahukirifx3605 at 9:08 you can see the flat cable that I found disconnected. It wasnt blocked...
@@davidefrYou didn't have a picture at all? Or was it of low brightness? What is visible only in the dark?
Hi everyone,
I have a Xiaomi Mi 4K Laser Projector 150" and I'm experiencing an issue where the projector only displays one color after a short time of use. When I first turn it on, the image appears normal with all colors working correctly.
However, after a few minutes, the screen shifts to displaying only a single color (e.g., red, green, or blue) and the other colors disappear.
Has anyone else experienced this issue? What could be causing it? I suspect it might be related to overheating, a failing laser, or some issue with the power supply. I'm not sure if this could be a hardware problem with one of the lasers or perhaps a cooling issue. Any advice on how to diagnose and fix this would be greatly appreciated.
Thanks in advance!
I tried repairing but now it is not starting and makes some sound
No light is passing
How can I contact u ?
From India 🇮🇳
Same behaviour after doing this. I've double checked all connections. Did you ever figure out what was wrong with yours?
I have the same problem. Did you fix it?
Can't get my projecter to turn on
I have vava UST projector that automatically turn off after a minute or 2? Can anyone help please)?
i changed the plate now the projector isn't starting up
how to repair, xiaomi mijia hd projector overheat, temperature sensor error
👍👍👍
Anyone familiar with the JMGO/SA🤔
Tried this. Broke one of the screws attaching the plate. Don't be like me. Don't break the screw. anyway, now it is foobar.
Too much slow
..