Permanent Magnet Synchronous Motor(PMSM) Drive using 3 phase sine PWM Inverter | open loop | MATLAB
ฝัง
- เผยแพร่เมื่อ 23 มี.ค. 2021
- At first watch this video to grab the complete idea of SPWM based 3 phase Inverter.
sine pwm based 3 phase Inverter | SPWM | MATLAB Simulation - • sine pwm based 3 phase...
In this video I have explained that how a PMSM electro magnetic torque(Te) and speed(w) change with respect to Load(TL).
LIKE SHARE SUBSCRIBE - วิทยาศาสตร์และเทคโนโลยี
U r genius bro ..
THANK YOU VERY USEFUL
hi brother can u please upload a vid integrating this model in a field oriented control for PMSM with the speedd reference and both park transformations and thnx
Very nice !
Thank you
Amazing explanation...Please upload video for closed loop control for the same PMSM motor
Thank you .Yes i will upload.
@@RanitSengupta hello sir, if it is in working, kindly may you send the simulibk model
@@kundankumar-dt5uu please share your mail id
@Ranit sangupta, sir kindly may you send this simulink, please sir
Hi Ranit, thank you for this great Video! Can you tell me how could i change the Sampling Frequency for the Inverter and PMSM to 150MHz ? and a Controller with 20Khz ?
would be a huge help
I would like to check the Current Control for the PMSM with this Parameter.
thank you
For inverter switching speed, you need to change the frequency of the carrier signal.
@@RanitSengupta thank you alot! I just send you an email.
@@RanitSengupta would you kindly send me the File ?
@Ranit sengupta.. Sir i have sent you email for forwarding this simulink model, I m using Matlab 2022a.
Hi! How can i simulate a dual three phase in simulink? I have the four dq equations but I don't know how to implement them in simuink. Can you help me pls?
Can you please mail me your query and if you have any supportive paper regarding this
ranitsengupta007@gmail.com
Hello sir can you send me this slx file.i have do the same but not getting as your output sir.
very useful for me sir.
sir can you explain how to pair to pmsm machine I need to know for my project work it will help me.
But I have to know first what you want to do? Means overall design.
@@RanitSengupta sir my project is on isolation and protection of synchronous motor generator pair during fault condition...on that I want to use PMS motor and generator pair and I am unable to pair both the machines.
@@nidhipandey6368 ok you please mail me this thing means your objective and also if you have any reference paper on this topic.mail id- ranitsengupta007@gmail.com
@@RanitSengupta ok sir thank you 😊
From the previous video on SPWM, when I am updating my model with this video, I get a negative angular velocity. And the output of the three-phase voltage is different in this video compared to your previous one. Can you please mention the changes that you have made?
you please ping me on this given mail id - ranitsengupta007@gmail.com
i will send you both the simulink file and please mention your matlab version in mail
@@RanitSengupta do you know about intelligent control technique of permanent magnet synchronous motor please let me know
@@shrungarpatil3076 I have done AI based control specially for SVpwm based PMSM control
@@RanitSenguptabasically how many control techniques are there
According to the changes in frequency in the sine wave, the speed has to change. But when i simulate, in this system I don't get changes. How to make it work?
Can you please send me your model
mail id- ranitsengupta007@gmail.com
Sir, i want to speed control of induction motor using spwm technique please help sir ....i try but output not show ....please send
Mail me- ranitsengupta007@gmail.com
Amazing video! really helpful
Could you send me the matlabs file of this project?
please send me your mail id.and your matlab version
Hello sir, i have applied step by step but when i run the model an error message appear "Derivative of state 1 in block PMSM iq at time 7.00000007E-5" any advise to fix this problem!?
Please change the step time in powergui Or run this in continuous domain
same issue
Hi bro. I used FOC svpwm control for pmsm. My foc and svpwm are working perfectly but my motor Speed decays to 0. I gave the load torque a constant equal to 1.
you have to give appropriate motor parameters
@@RanitSengupta I'll look into that. One more thing is that our inverter is realised using a multiport switch and not using actual mosfet circuit, so my guess is that required current is not supplied by multiport switch as it only takes care of discrete voltages only. What's your viewpoint on this
Hello dear, can you share the simulink model, please
@@dhaneshprabhu72 can you share with me the matlab file
When trying to control the speed in open loop then my output speed gets half. What would be the reason??
But how you can control the speed open loop.close loop control must be required.
Hello,
I am getting the following as error, kindly help
"The Voltage Measurement block 'untitled/Three-Phase V-I Measurement/Model/U A:' is connected between two isolated networks. For a valid measurement, the positive and negative terminals of the block must be connected to electrical nodes that are part of the same electrical circuit. Also check if the ground reference node is defined for that circuit."
Please give me your mail id and matlab version I will send you the matlab file
@@RanitSengupta where can i send you email if i dont want to write it in comments?
@@argentumnocturne3446 ranitsengupta007@gmail.com
Double click on three phase V I measurement and in voltage measurement select phase to phase
Hello sir how can we do this with pid control ?
For pmsm there are multiple control techniques present.you can get the overview from literature.
I'm studying power electronics and it has been a great help! Can you kindly send me the simulation file please?
please share your mail id
Thank you. Google bot seems delete addresses. Gmail address.
@@user-pf3nd8wg8i please mail me. may mail id is mentioned on my channel about
I have sent you a mail mentioned on the channel!
Hi, How to apply negative torque to the PMSM to charge a battery?
Here you can apply negetive torque in the step block which is our mechanical torque input to the motor.
Sir, Can you please upload FOC of PMSM motor using ANN controller?
Hello @loyel rose, have you done that?
Sir I done the exactly same as yours but my speed is negative, what's the reason for that
My be your PMSM parameters differ or the solver settings
Hello. Nice job. Could you provide me this project ?
please send me your mail id and matlab version
Hi what defines the rated of pmsm?
Sorry I can't understand your question?
hi sir... can you help me in my project ,please? I need your help.
Hi sir can u please send me this Matlab file,i got the error during simulation
Sure. Please share your mail id or ping me on mail- ranitsengupta007@gmail.com
Hello Ranit, Can you send me this Matlab file? I'm using MatLab version 2021
Please share your mail id
hello,
can you please send me PMSM model operate on PWM , if u have ?
Yes I can.please send me your mail id
can you send the simulation file ,please
Please share your mail id
Hi, can you give me the matlab project
@samuel daba Yea sure. Kindly share your mail id and matlab version you are using.
can you please send me a model sir
Please share your mail id
Hi Ranit, i'm studying this PMSM motor can you send me the simulation please ?
Please share your mail I'd or ping me at ranitsengupta007@gmail.com
Hi can u help me in a matlab project?
How can I help you.you ping me by mail. ranitsengupta007@gmail.com
@@RanitSengupta mail done
Can you watsapp me +61426080577
@@MrSingh-yb7ey But i didn't receive your mail.
Done
Ranit, hello. Can you send this file to me?
Yes please share your mail id
@@RanitSengupta can you send it for me please
@@sahlileila6382 please share your mail id
Hi ranit can you send the file to me?
Please share your mail id
Could you send me this matlab project sir?
Yes please tell me your mail id
@@RanitSengupta Hi could you please check your emails:) Thank you
@@eyawadiai2060 ok
@@RanitSengupta Thank you so much 🥺
@@eyawadiai2060 hello may you guide me about it
nOT WORKING IN R2018A
please send me your model by mail
ranitsengupta007@gmail.com
Brother i sent you the email. kindly provide me the matlab simulink files as i am master's student. it will help alot