Thank you for this information. It solved my issue on a 2010 Gl450 (low miles). Intermittend start, sometimes no start for 5 minutes, very frustrating feeling. When I openened the module after removal (used a $10 tool from Amamzon, did not want to scratch anything up), the white plug was stuck EXACTLY as shown in your video. I was a little nervous regarding the soldering part (I have the tools, just not something I do on a daily basis). This is what worked for me: 400 degree setting, thin, pointy tip and I did not add material, just carefully placed the white part with the contacts into place and heated the existing solder at the base up (one at a time), thereby getting the tiny feet of the contacts re-seated. 2x3=six contacts total (two sides three each). The white plastic part was making strong contact with the board, nothing was loose. Tested it, car had power right away. So far 10 starts and everything works as should. Oh, i used toothpicks for opening the plastic latches on the unit (keep them open while going around), that made it a lot easier. I dont think I would have beeen able to do this without your video, thank you very much! ~
Have a 2010 Gl450 with exact same problem. Tomorrow, i'm gonna do exactly what you did, and I'm hoping that I find exactly what you found. Great video, thank you very much.
Same problem exactly - 2007 clk280 amg. Scary but going to dive in and have a look. When it comes to cars, being brave and having a go yourself saves you thousands, and if you balls it up - well you were going to have to pay anyway. At least i can do fine soldering. Thanks so much for this video man
Sadel really good information! Most likely we're gonna have this problem in the future or one of our friends! Thank you for sharing brother! Take care!
Great fix, Sadel. I think if most others opened up the ESI module they wouldn’t have caught that piece stuck to the other board since it looked like it belonged there.
I’m having this problem right now with my 2011 ML350, going to try this. Don’t even care if it fixes it, this is a fantastic video! Great job. Impressed!
Thanks, had same symptoms with inconsistent start BAS ESP and turn signal lights. Opened up housing and found dirty optical path and lens. Used q tip and contact cleaner also for a couple copper spring loaded contacts. Now all works. So may be other issue related to EIS which wont require solder or new switch
As of 2/15/23, I was informed by MB dealer - "one-year backlog on this EIS part ( not sold to independent shop). Est. Cost to replace at dealer: $2,400.00. SERIOUSLY. WTF.
Bonito video como siempre primo . Tengo una 2015 sprinter y da ignition pero no gira la marcha . Le pongo corriente de la batería y gira pero no enciende únicamente encendió una vez así . El eis bloquea el diésel? Que bloqueó para que no encienda ? Ayúdeme plis primo
Company in Canada that fixes it for $200 And they turn it around and return ships it The same day. MB should start using them! Very easy fix that you can do yourself and save $2200
I have a ml350 and sometimes it will start and sometimes won’t start but when it’s warmed up it starts up fine I have checked all starter alternators battery everything good I’m hoping it’s the Eis switch
PRODIGY D-Techs Engineering My teacher Thanks for sharing it with us Thank you very much helpful information video Take care and have a great day PRODIGY D-Techs Engineering From Nick Ayivor from London England UK 🇬🇧 ⏰️ 00.22
Same problem here with a 2012 MB GLK 350. Don't know if it is the same problem. But the private shop already toll me the cost to fix it $1200 plus labor
Thank you for this information. It solved my issue on a 2010 Gl450 (low miles). Intermittend start, sometimes no start for 5 minutes, very frustrating feeling. When I openened the module after removal (used a $10 tool from Amamzon, did not want to scratch anything up), the white plug was stuck EXACTLY as shown in your video. I was a little nervous regarding the soldering part (I have the tools, just not something I do on a daily basis). This is what worked for me: 400 degree setting, thin, pointy tip and I did not add material, just carefully placed the white part with the contacts into place and heated the existing solder at the base up (one at a time), thereby getting the tiny feet of the contacts re-seated. 2x3=six contacts total (two sides three each). The white plastic part was making strong contact with the board, nothing was loose. Tested it, car had power right away. So far 10 starts and everything works as should. Oh, i used toothpicks for opening the plastic latches on the unit (keep them open while going around), that made it a lot easier. I dont think I would have beeen able to do this without your video, thank you very much!
~
That's great to hear and I'm glad it helped!
Have a 2010 Gl450 with exact same problem. Tomorrow, i'm gonna do exactly what you did, and I'm hoping that I find exactly what you found. Great video, thank you very much.
Glad I could help and good luck
Same problem exactly - 2007 clk280 amg. Scary but going to dive in and have a look. When it comes to cars, being brave and having a go yourself saves you thousands, and if you balls it up - well you were going to have to pay anyway. At least i can do fine soldering. Thanks so much for this video man
hope this helps you get it fixed! 👍
Sadel really good information! Most likely we're gonna have this problem in the future or one of our friends! Thank you for sharing brother! Take care!
Glad it was helpful!
Been so long since Ive done one of these I forgot about it. Thanks for the refresher. I used to run into that bad connector a lot.
Yeah, oddly enough it was my first experience with that. Thank you for watching
I’ve never taken one apart! Dealer phone call and then replaced !!🙌🏻💯 you the man
Great fix, Sadel. I think if most others opened up the ESI module they wouldn’t have caught that piece stuck to the other board since it looked like it belonged there.
Yeah I almost missed it too
I’m having this problem right now with my 2011 ML350, going to try this. Don’t even care if it fixes it, this is a fantastic video! Great job. Impressed!
Good luck! thank you for watching
Great work and appreciate you for sharing this. You fixed instead of replacing. Thank you. 👏🏽👏🏽
Thanks for watching!
Thanks, had same symptoms with inconsistent start BAS ESP and turn signal lights. Opened up housing and found dirty optical path and lens. Used q tip and contact cleaner also for a couple copper spring loaded contacts. Now all works. So may be other issue related to EIS which wont require solder or new switch
As of 2/15/23, I was informed by MB dealer - "one-year backlog on this EIS part ( not sold to independent shop). Est. Cost to replace at dealer: $2,400.00. SERIOUSLY. WTF.
There is many aftermarket support parts and service for the replacement of this module.
Very helpful video sir. Do you have some closeup of where the soldering was bad ? Dealer asking 1500. Apparently you can’t order one yourself :(
it was at the pins I showed in the video. you can send it out for the repair if you cannot buy a new one, let me know.
@@DTEAutohow much
Amazing! Now I need to be careful learning how to properly solder it! If you have a video on it, or suggestions, I'll be forever grateful.
I'm so excited i want to go out to the garage right now but its 2am.
Bonito video como siempre primo .
Tengo una 2015 sprinter y da ignition pero no gira la marcha .
Le pongo corriente de la batería y gira pero no enciende únicamente encendió una vez así .
El eis bloquea el diésel?
Que bloqueó para que no encienda ?
Ayúdeme plis primo
I would like to know what scanner would you recommend if I was looking to purchase to do this sort of work??? Can you please help
I would look into Autel, Launch or Topdon
What is the name of the part that you soldered back and where do you buy that at electronic store???
It was the connector that came off the circuit board, I didn't have to buy any pieces, just solder the connector back onto the board.
Muy bonito como dice Iván no parts require.
Company in Canada that fixes it for $200
And they turn it around and return ships it
The same day. MB should start using them! Very easy fix that you can do yourself and save $2200
What’s the name?
DTech Engineering can you come to Texas and fix mine?
send me your ignition switch
2011 ml350 dash would light up but no crank had a 1321 code this solved my issue
I have a ml350 and sometimes it will start and sometimes won’t start but when it’s warmed up it starts up fine I have checked all starter alternators battery everything good I’m hoping it’s the Eis switch
hopefully so
What was the problem? I am having similar problem in my w212 2014
Exelente 👏👏
Nice fix!
Thanks PJ!
Great job, thank you!
Bravo, excellent video
Glad you liked it!
PRODIGY D-Techs Engineering
My teacher
Thanks for sharing it with us Thank you very much helpful information video
Take care and have a great day
PRODIGY D-Techs Engineering
From Nick Ayivor from London England UK 🇬🇧 ⏰️ 00.22
Good Work..!
This is what is happening with my ML350 ,let me open it up and try it
Hope you get issue rectified
Same problem here with a 2012 MB GLK 350.
Don't know if it is the same problem.
But the private shop already toll me the cost to fix it $1200 plus labor