@@adewalesunday5910 I used the temporary solution. First, unplug the power cable then unplug the signal cable. Plug back the power cable and wait until it loads the channels and when signal is now required then plug in the signal cable. It's temporary and therefore you will have to do it everytime you switch off your Tv from power source.... also the issue is caused by poor network otherwise the procedure in the video works.
If it goes over 2 minutes, simply restart the gotv and don't touch it. It will pick up by it self and start to display. If it doesn't, try the steps all over again. If your gotv shows the upgrade issue each time you power it on, then try to change your subscription to another one. That also helps to fix the issue permanently Good luck.
Thanks. I watched your video and followed the steos and finally it worked. Thanks
Glad it helped
Must I have my subscription running to enable me do this?
Mine the decoder is showing the red light but it's not showing any signal on tv. I suspect the decoder sensor, can I use this pattern ?
Can I press the p- and p+ on my remote??
Because my decoder buttons have been deactivated
My problem is when it get to 22sec toward the final stage, the decoder will off by it self and start showing upgrade decoder
Code does not show.....i guess a recent update for 2024 is needed...
Thanks
During the download part it is writing "Front end-lock failed"
Muito obrigado, ajudou bastante.. fiquei dois dias sem ver TV por conta deste problema. Deus abençoe
Mine is not showing the three zeros when I press down the p+ sign
my decorder is showing front end error failed then exiting itself
how were you able to solve this please
@@adewalesunday5910 I used the temporary solution. First, unplug the power cable then unplug the signal cable. Plug back the power cable and wait until it loads the channels and when signal is now required then plug in the signal cable.
It's temporary and therefore you will have to do it everytime you switch off your Tv from power source.... also the issue is caused by poor network otherwise the procedure in the video works.
Thanks so much, mine actually worked now
Glad we could help
I followed everything as told but instead it's load fast ND go back boot up...then go back to how it's was
Do I have to do this every time I want to watch my gotv?
If it continues, I will advise you upgrade to another gotv plan. It will stop
Tanx Soo much for dis, I did my own now❤
Thanks o meu problema esta resolvido From Mozambique 🇲🇿
Thank you so much, this really helped me 😊and mine is working now
Glad it helped!
I did it and after watching for few minutes it told me it will be maintained in few seconds after that it continued the upgrade again
I'll suggest you repeat same procedure. If it continues, you have to call the customer care then.... Sorry for the late reply
Same to my decoder
After all the doings my decorda still go bafk ti load again
Thank you guy it works
Thanks a lot totally worked. Awesome
You're welcome!
Mine is not working it has even gone over 10mins please help
If it goes over 2 minutes, simply restart the gotv and don't touch it. It will pick up by it self and start to display. If it doesn't, try the steps all over again. If your gotv shows the upgrade issue each time you power it on, then try to change your subscription to another one. That also helps to fix the issue permanently
Good luck.
@@hitvibz thanks I'll try
@@hitvibzplease how do I change my subscription?
Thank you very much for your help I really appreciate I also did it, it started showing in just a few seconds😢😢😮
I just subscribe 3 days ago it’s not showing when it finally shows big brother channels is not showing it’s telling me invalid channel
Me too 😢
You only bypass the update. No solution proffered
Why mine is not taking 22 mins
mine says it found an error and stoped
I have tired mine more than 10 time and it is not working it is say front end failed
Same here
Thanks so much dis was very help to me
I’ve tried this more than 10 times and it’s still not working
Same here
Dope
I did it it doesn't download it will go back to the same deocoder is running old software
Take it to their office for upgrade then
Thanks so much bro you are the best
Very helpful thnx!
You are welcome
You're the best ❤❤ very helpful
thanks, the video helped to much
How far Go tv
Thank you it worked
Wao…so cool thanks much for the info
Any time!
God bless you bro❤
D code is not showing
Rewatch the tutorial again
Thanks 🙏
It worked thanks brother
Worked ✅
Thank you very much sir ❤
Thank you so much
You're most welcome
Thank you very much 🎉👍💓💓🥳😍😁
Mine didn't work
Try again, carefully this time and if still didn't work, take it to their office
God bless you
Thank you❤
Does it require an Internet connection, please?
Wow😂😂,it was quite helpful
Glad to hear that
You are awesome🎉🎉
Thanks
I love it work
Thank u❤
You're welcome 😊
Electric shock mi
I did and it worked but the next day he did the same.
The code must be 0001 or dere is other code to use
Unfortunately, no other code to use
Code is not showing o
You must press when ti starting processo imidiatly
Thanks bro
You're welcome
Thanks gee❤
Thank you so much
You're most welcome