Hi., It was a good explanation. Would you be able to help us on the Purafil Air filtration system with the controls for the turbines and the details of its facilitators or service providers?
I live in colder climate. The cold air makes our emissions for both co2 go high and nox go high. We are unable to add nox water because of the already high co2 reading. What method is there to “warm” that inlet air to stop this problem?
Thank you for watching my videos. There is no measurements for incoming air and it will be different for different igv openings. But for total exhaust flow(air + fuel ) there is a calculated value available in gas turbines. If you know the tag number for your machine you can find the value
The normal path from the air filter is outside to inside where atmospheric air is filtered and dust accumulation is on filter happen, in self cleaning cycle there is a solenoid operated compressed air supply is placed inside, once inside valve open cleaning is done
Hello. Air flow increases as per MW increase. As higher MW requirement is higher fuel requirements and higher fuel requirements is higher air requirement. IGV plays that role to control the requirements of maneuvering the air flow.
Thank you for asking questions.. Inlet air filters draws lot of air and with air, dust , sand aerosol fine particles come and they sit on the filter surfaces because air filters can prevent particles of more than 3 micron. Slowly these particles keep deposit on filter surfaces and reducing surface area from air can pass. This is when dp starts increasing. Now, you can imagine efforts from sucking air from clean filter and dirty filters. And this will cause in less air flow to compressor and then reducing the output. ' Hope I have answered your questions. If not, please ask again. Will try to answer
@@powerplantguru007 Thank you for the answer. I want to ask another question. When the dp high, it is indicates that the filter is already dirt or covered by the contaminants, the common action that we can take is just replace the dirty filter with the new one, and it will cost the company because they have to spent more, especially when the interval of the filter change is short. Is there any possibly solution to decrease the DP itself, and make the interval change of filter is longer? Thank you in advanced
Hi thanks for reaching out. I would suggest a few things on this. 1. Keep Check on pulsating air filters cleaning system pressure and it's all sov are working. Keep operator rounds and ask in each round if he can listen bump sounds of filters back cleaning. 2. Keep a dust extraction conveyor in working condition from the dirty side of air filters. 3. You can install a very low cost wrapper (type of filter) for covering air filters from outside, this will wrapper are washable and once you face sudden increase of dp you can remove those wrapper also and then you have relief from emergency. Then your wash the wrapper and again install. This way you can increase the life of filters.
These are some practice which are recommended. You can check it's application with your make and model of machine. It may be different for different machine
and also you failed top mention if an inlet has mist elimanator or not and the effect of it on the filters and if one has chiller coils instead of an evap cooler or if it dosent have one at all
Could you please help me with mechanical QC engineer interview at Air filters manufacturing company? It's urgent please email me or comment it here. Thanks
Great your Job. Well Explained and easy understand.
Thank you. Please subscribe to my channel for more information.
Excellent, expect to have your more post
Nice content
Hi., It was a good explanation. Would you be able to help us on the Purafil Air filtration system with the controls for the turbines and the details of its facilitators or service providers?
Okay Sure
Amazing
Thanks for support
Well explained
Thank you. Please subscribe to my youtube channel for more information.
I live in colder climate. The cold air makes our emissions for both co2 go high and nox go high. We are unable to add nox water because of the already high co2 reading. What method is there to “warm” that inlet air to stop this problem?
please tell me why the water could be existense in outlet air of casing the compressor which provided auto drain system
Can you please be more specific,
There are water wash drains , i don't understand if you are talking about those
How can we measure the mass flow rate of the incoming air?
Thank you for watching my videos.
There is no measurements for incoming air and it will be different for different igv openings. But for total exhaust flow(air + fuel ) there is a calculated value available in gas turbines. If you know the tag number for your machine you can find the value
thanks
Welcome
How filter can self cleaned...
APU is the unit which works for self cleaning. The air pressure from APU comes in opposite direction of normal flow and push the dust accumulation
This will reduce the filter ageing
@@powerplantguru007 How the opposite direction of normal flow can work..
The normal path from the air filter is outside to inside where atmospheric air is filtered and dust accumulation is on filter happen, in self cleaning cycle there is a solenoid operated compressed air supply is placed inside, once inside valve open cleaning is done
@@powerplantguru007 Thanks for explanation..
Why does inlet air flow decrease when the load MW increases? What is the relationship ?
Hello.
Air flow increases as per MW increase. As higher MW requirement is higher fuel requirements and higher fuel requirements is higher air requirement.
IGV plays that role to control the requirements of maneuvering the air flow.
Can the evap media be re used
Hello Frank
I understand that the media can be reused.
Sir why VAM is used in inlet air filter house.
th-cam.com/video/I7UQ7Do-oTU/w-d-xo.html
Please watch one of my videos, i have explained it here
Is it Airfilter self cleaning?.
Thank you for watching my videos.
Self cleaning is there in almost all machines.
Sir, whats affect the dp (differential pressure) to change? Whats the effect cause by this dp on a system?
Thank you for asking questions..
Inlet air filters draws lot of air and with air, dust , sand aerosol fine particles come and they sit on the filter surfaces because air filters can prevent particles of more than 3 micron.
Slowly these particles keep deposit on filter surfaces and reducing surface area from air can pass. This is when dp starts increasing.
Now, you can imagine efforts from sucking air from clean filter and dirty filters. And this will cause in less air flow to compressor and then reducing the output. '
Hope I have answered your questions.
If not, please ask again. Will try to answer
@@powerplantguru007 Thank you for the answer. I want to ask another question. When the dp high, it is indicates that the filter is already dirt or covered by the contaminants, the common action that we can take is just replace the dirty filter with the new one, and it will cost the company because they have to spent more, especially when the interval of the filter change is short. Is there any possibly solution to decrease the DP itself, and make the interval change of filter is longer? Thank you in advanced
Hi thanks for reaching out.
I would suggest a few things on this.
1. Keep Check on pulsating air filters cleaning system pressure and it's all sov are working. Keep operator rounds and ask in each round if he can listen bump sounds of filters back cleaning.
2. Keep a dust extraction conveyor in working condition from the dirty side of air filters.
3. You can install a very low cost wrapper (type of filter) for covering air filters from outside, this will wrapper are washable and once you face sudden increase of dp you can remove those wrapper also and then you have relief from emergency. Then your wash the wrapper and again install. This way you can increase the life of filters.
These are some practice which are recommended. You can check it's application with your make and model of machine. It may be different for different machine
@@powerplantguru007 alright, thank you sir
and also you failed top mention if an inlet has mist elimanator or not and the effect of it on the filters and if one has chiller coils instead of an evap cooler or if it dosent have one at all
Could you please help me with mechanical QC engineer interview at Air filters manufacturing company? It's urgent please email me or comment it here. Thanks