Deans Marine 'Yarra' motor and rudder setup test

แชร์
ฝัง
  • เผยแพร่เมื่อ 12 ม.ค. 2025

ความคิดเห็น • 16

  • @raymondvollebregt-videogra212
    @raymondvollebregt-videogra212 7 ปีที่แล้ว +3

    what size motors are those, and the KV rating. together with the prop size ?

  • @websitesthatneedanem
    @websitesthatneedanem 8 ปีที่แล้ว +2

    Nice setup!.... can you water ski behind that! ;-)

  • @Poonslaya
    @Poonslaya 8 หลายเดือนก่อน

    Hi there could you advise what all the rudder parts are and where I can also get them. I plan to make a bait boat using fleet scale 1/96 river class fibreglass hull. First boat build and I am impressed with your setup. Thanks

    • @lverkuijl
      @lverkuijl  8 หลายเดือนก่อน +1

      Yes I can, the rudders are made out off aftermarket universal RC boat rudders in aprox. the same saze as the Deans Marine set. They have been cut to make the flap. Hinges and controll pin are made with brass rod and tubing. You can't buy them as these are in this size as far as I know.

    • @Poonslaya
      @Poonslaya 8 หลายเดือนก่อน

      @@lverkuijl thank you very much. My next question is this. I have had a look at the motors you used however they are now discontinued as your build is now 7 years ago. Could you recommend motors for me that spin up like the ones you have in the video. Also the shrouds for the props would you mind letting me know what they are aswell. Thanks

    • @lverkuijl
      @lverkuijl  8 หลายเดือนก่อน +1

      @@Poonslaya Any motor 500 to 700 KV will do. The smooth running is not in the motor but in the ESC. Use car ESC's with forward-reverse, with no break function, of where you can switch to direct forward-reverse. XC-10A ESC's have proven to be good in conjuction with the programmer card. Set to direct forward-reverse, and low start power. Search AliExpress on "XC-10a".

    • @Poonslaya
      @Poonslaya 8 หลายเดือนก่อน

      Thank you for your input. I am only concerned about the motors not being powerful enough they need to be able to go in the sea and seal with some surf I have seen 1900kv out runners I may go for them and then do as you say regarding the esc

  • @derpreue3947
    @derpreue3947 4 ปีที่แล้ว

    Hallo, can you advise on some specifics: motor size, KV , Prop diameter. Shaft length and sleeve diameter.Usual stuff...

    • @lverkuijl
      @lverkuijl  4 ปีที่แล้ว

      Hi,
      Motors are PROPDRIVE 2830 750KV from Hobbyking, ESC are HobbyKing Brushless Car ESC 10A w/ Reverse, propellers 40mm Raboesch. Shaftlength I dont know without mesuring, but they are also Raboesch, and you can shorten them. Couplings are 4 x 4 mm double joint from Graupner.

  • @sergendel
    @sergendel 6 ปีที่แล้ว

    What these metal bumps on the rudder and nozzle are for ? Thank you .

    • @lverkuijl
      @lverkuijl  6 ปีที่แล้ว

      Those are sacrificial anodes. Well, not realy zink, but made of plastic ;-)

    • @sergendel
      @sergendel 6 ปีที่แล้ว

      Lex Verkuijl Thank you) can you tell me the purpose of it? Does it help to keep the flow laminar?

    • @lverkuijl
      @lverkuijl  6 ปีที่แล้ว

      On real boats these anodes help to reduce the corrosion of certain parts. The zink is a weaker metal then steel or aluminium. It corodes first, so the steel parts stay untouched. Hence 'sacrificial anodes', you sacrifice them to protect the hul an parts. If they are worn out you simply replace them with new ones, the are screwed on to the parts.

    • @sergendel
      @sergendel 6 ปีที่แล้ว

      man , you are great ! thank you ! )

  • @davegeorge7094
    @davegeorge7094 6 ปีที่แล้ว +1

    don't forget to dry boat before you leave the lake. Zebra mussels etc.. big fine if u don't. Lock u up.